Table of Contents
Advertisement
Quick Links
SERVICE MANUAL
MODEL
COMMANDER
KV-VF14M40
RM-956
KV-VF14M70
RM-956
KV-VF14M70
RM-956
KV-VF14M77
RM-955
• Refer to the SERVICE MANUAL of VHS MECHANICAL
ADJUSTMENTS VI for Mechanical Adjustments. (9-921-647-11)
EJECT
Z
PIC MODE
TAPE SPEED
zREC
REW
m
MENU
COUNTER RESET
t
1
4
7
-/--
2
RM-955
∗ Please file according to model size. ....
21
DEST. CHASSIS NO.
GE
SCC-U31A-A
ME
SCC-P11B-A
E
SCC-P10B-A
HK
SCC-P09C-A
EJECT
Z
PIC MODE
TIMER REC G-CODE ON/OFF
TAPE SPEED
TIMER REC G-CODE ON/OFF
zREC
INDEX
INDEX
.
>
.
>
X PAUSE
X PAUSE
FF
REW
FF
PLAY
PLAY
H
M
m
H
M
ENTER
ENTER
x STOP
x STOP
A/B
MENU
COUNTER RESET
GAME
t
GAME
2
3
1
2
3
5
6
4
5
6
8
9
7
8
9
0
C
-/--
0
C
2
PROGR
PROGR
RM-956
BC-4A
MODEL
COMMANDER
TRINITRON
COLOR VIDEO TV
®
CHASSIS
DEST. CHASSIS NO.
PAL NTSC
®
(VF14M77 ONLY)
Advertisement
Chapters
Table of Contents
Related Manuals for Sony TRINITRON KV-VF14M70
Summary of Contents for Sony TRINITRON KV-VF14M70
-
Page 1: Service Manual
SERVICE MANUAL BC-4A CHASSIS MODEL COMMANDER DEST. CHASSIS NO. MODEL COMMANDER DEST. CHASSIS NO. KV-VF14M40 RM-956 SCC-U31A-A KV-VF14M70 RM-956 SCC-P11B-A KV-VF14M70 RM-956 SCC-P10B-A KV-VF14M77 RM-955 SCC-P09C-A • Refer to the SERVICE MANUAL of VHS MECHANICAL ADJUSTMENTS VI for Mechanical Adjustments. (9-921-647-11) EJECT EJECT PIC MODE... -
Page 2: Tv Section
SPECIFICATIONS TV Section Television system B/G, I, D/K, M Inputs and Outputs Color system PAL/SECAM and t1, t2/GAME IN Inputs NTSC /NTSC (video): phono jack 3.58 4.43 Bilingual system NICAM bilingual I 1 Vp-p, 75 ohms, Channel coverage See “Receivable unbalanced, channels and channel sync negative... - Page 3 Receivable channels and channel display System Area Channel coverage Channel display B/G, H Middle East/Asia E-2 to E-12 C02 to C12 E-21 to E-69 C21 to C69 Indonesia 2 to 11 C03 to C12 Morocco M-4 to M-7 C70 to C73 M-8 to M-10 C08 to C10 CATV...
-
Page 4: Table Of Contents
THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. RE- PLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. CIRCUIT ADJUST- MENTS THAT ARE CRITICAL FOR SAFE OPERATION ARE IDENTIFIED IN THIS MANUAL. - Page 5 SELF DIAGNOSTIC FUNCTION OUTLINE • The units in this manual contain a self-diagnostic function. • If an error occurs, the STANDBY lamp will automatically begin to flash. The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference.
- Page 6 DISPLAY OF STANDBY LIGHT FLASH COUNT * One flash count is not used for self-diagnostic. < Diagnostic Item > < Flash Count > • +B OCP/OVP 2 times • Vertical deflection stopped 4 times STANDBY lamp (RED) • White balance failure 5 times Lamp ON 0.3 sec.
- Page 7 SELF-DIAGNOSTIC CIRCUIT LED flash IC001 µ-COM STANDBY lamp To item 2 and 5 via bus line SCL1 D1308 SDA1 RY601 LED1 RELAY • • MEMORY IC004 ITEM 3 Over current Q601 Detection(OVP) Q606 V PULSE R611 STOP • R656 R613 +B LINE IC301 Y/C/J...
- Page 9 EJECT PIC MODE TIMER REC G-CODE TAPE SPEED ON/OFF zREC INDEX > X PAUSE PLAY ENTER x STOP MENU COUNTER RESET GAME PLAY PLAY ENTER ENTER...
- Page 10 EJECT PIC MODE TAPE SPEED TIMER REC G-CODE ON/OFF PLAY PLAY zREC INDEX > ENTER ENTER X PAUSE PLAY ENTER x STOP MENU COUNTER RESET GAME PLAY PLAY ENTER ENTER PLAY PLAY ENTER ENTER PLAY PLAY ENTER ENTER...
- Page 11 EJECT PIC MODE TAPE SPEED TIMER REC G-CODE ON/OFF zREC INDEX > X PAUSE PLAY ENTER x STOP MENU COUNTER RESET GAME PLAY PLAY ENTER ENTER PLAY ENTER PLAY PLAY ENTER ENTER...
- Page 12 PLAY PLAY ENTER ENTER STOP –PLAY– PAUSE TIMER REC QUICK TIMER GAME PROGR PUSH...
- Page 13 EJECT PIC MODE TIMER REC G-CODE TAPE SPEED ON/OFF zREC INDEX > X PAUSE PLAY ENTER x STOP MENU COUNTER RESET GAME PROGR PROGR...
- Page 14 EJECT PIC MODE TAPE SPEED TIMER REC G-CODE ON/OFF zREC INDEX > X PAUSE PLAY ENTER x STOP MENU COUNTER RESET GAME PLAY ENTER...
- Page 16 EJECT PIC MODE TAPE SPEED TIMER REC G-CODE ON/OFF zREC INDEX > X PAUSE PLAY ENTER x STOP MENU COUNTER RESET GAME PROGR PROGR...
- Page 17 EJECT PIC MODE TAPE SPEED TIMER REC G-CODE ON/OFF zREC INDEX > X PAUSE PLAY ENTER x STOP MENU COUNTER RESET GAME TAPE SPEED : SP...
- Page 18 TAPE SPEED : SP...
- Page 19 TAPE SPEED : SP EJECT PIC MODE TAPE SPEED TIMER REC G-CODE ON/OFF zREC INDEX > X PAUSE PLAY ENTER x STOP MENU COUNTER RESET GAME PROGR...
- Page 20 PLAY PLAY ENTER ENTER EJECT PIC MODE TAPE SPEED TIMER REC G-CODE ON/OFF zREC INDEX > X PAUSE PLAY ENTER x STOP MENU COUNTER RESET GAME PLAY PLAY ENTER ENTER TAPE SPEED...
- Page 21 TAPE SPEED TAPE SPEED PLAY SP MAIN ENTER EJECT PIC MODE TAPE SPEED TIMER REC G-CODE ON/OFF zREC INDEX > X PAUSE PLAY ENTER x STOP MENU COUNTER RESET PLAY ENTER PLAY PLAY ENTER ENTER...
- Page 22 PIC MODE TAPE SPEED TIMER REC G-CODE ON/OFF zREC INDEX > X PAUSE PLAY ENTER PLAY ENTER x STOP MENU COUNTER RESET MON · SAT EVERY TUE...
- Page 23 EJECT PIC MODE TAPE SPEED TIMER REC G-CODE ON/OFF zREC INDEX > X PAUSE PLAY ENTER x STOP MENU COUNTER RESET GAME PLAY PLAY ENTER ENTER PLAY PLAY ENTER ENTER PLAY PLAY ENTER ENTER...
- Page 24 PLAY PLAY ENTER ENTER PLAY PLAY ENTER ENTER PLAY PLAY ENTER ENTER...
- Page 25 PLAY PLAY ENTER ENTER PLAY PLAY ENTER ENTER...
- Page 26 EJECT PIC MODE TIMER REC G-CODE TAPE SPEED ON/OFF zREC INDEX > X PAUSE PLAY PLAY ENTER ENTER PLAY ENTER x STOP MENU COUNTER RESET GAME PLAY PLAY ENTER ENTER PLAY PLAY ENTER ENTER...
- Page 27 PLAY PLAY PLAY PLAY ENTER ENTER ENTER ENTER PLAY PLAY ENTER ENTER PLAY PLAY ENTER ENTER...
- Page 28 PLAY PLAY ENTER ENTER PLAY PLAY ENTER ENTER PLAY PLAY ENTER ENTER PLAY PLAY ENTER ENTER PLAY ENTER...
- Page 29 PLAY PLAY ENTER ENTER PLAY PLAY ENTER ENTER PLAY PLAY ENTER ENTER...
- Page 30 EJECT EJECT PIC MODE PIC MODE TAPE SPEED TIMER REC G-CODE ON/OFF TAPE SPEED TIMER REC G-CODE ON/OFF zREC INDEX zREC INDEX > > X PAUSE X PAUSE PLAY PLAY ENTER ENTER x STOP x STOP MENU COUNTER RESET MENU COUNTER RESET GAME GAME...
- Page 31 EJECT PIC MODE TAPE SPEED TIMER REC G-CODE ON/OFF zREC INDEX > X PAUSE PLAY ENTER x STOP MENU COUNTER RESET GAME PLAY ENTER...
- Page 32 EJECT PIC MODE TAPE SPEED TIMER REC G-CODE ON/OFF zREC INDEX > X PAUSE PLAY ENTER x STOP MENU COUNTER RESET GAME...
- Page 33 EJECT PIC MODE TIMER REC G-CODE TAPE SPEED ON/OFF zREC INDEX > X PAUSE PLAY ENTER x STOP MENU COUNTER RESET GAME EJECT PIC MODE TAPE SPEED TIMER REC G-CODE ON/OFF zREC INDEX > X PAUSE PLAY ENTER x STOP MENU COUNTER RESET GAME...
- Page 34 EJECT PIC MODE TIMER REC G-CODE TAPE SPEED ON/OFF zREC INDEX > X PAUSE PLAY ENTER x STOP MENU COUNTER RESET GAME...
- Page 37 PROGR PUSH EJECT STOP –PLAY– PAUSE...
- Page 38 EJECT EJECT PIC MODE PIC MODE TAPE SPEED TIMER REC G-CODE ON/OFF TAPE SPEED TIMER REC G-CODE ON/OFF zREC INDEX zREC INDEX > > X PAUSE X PAUSE PLAY PLAY ENTER ENTER x STOP x STOP MENU COUNTER RESET MENU COUNTER RESET GAME GAME...
- Page 39 MEMO ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○...
-
Page 40: Disassembly
SECTION 2 DISASSEMBLY 2-1. REAR COVER REMOVAL 2-2. CHASSIS ASSY REMOVAL 2 Rear cover 1 Eight screws (+BVTP 4 × 16) Cassette door 2 Chassis assy Caution: 1 Before the chassis assy removal, please make sure the power cord is pull out to prevent electric shock. 2 Notice for Installing chassis assembly Note: Install chassis assembly when keep... -
Page 41: Harnes Location
2-5. HARNESS LOCATION Demagnetic coil Anode cap Deflection yoke DGC holder DGC holder VM coil MA10 board CV board Red( + ) White( - ) CN251 Speaker CN001 CN002 CN1003 CN303 CN302 CN301 CN305 CN304 Tuner board CN803 CN801 CN602 CN604 CN603 CN601... -
Page 42: Picture Tube Removal
2-6. PICTURE TUBE REMOVAL DGC clip 0 Two spring 9 Degaussing coil 2 Two screws (+BVTP 4 X 16) 4 CV board 3 Chassis assembly 6 Deflection yoke !¡ Four screws (Tapping screw 5) !™ Picture tube 1 Anode cap 7 Top support Cassette door Cushion... -
Page 43: Set-Up Adjustments
SECTION 3 SET-UP ADJUSTMENTS Perform the adjustments in the following order: • The following adjustments should be made when a complete realignment is required or a new picture tube is installed. 1. Beam Landing 2. Convergence • These adjustments should be performed with the rated power supply voltage, unless otherwise noted. -
Page 44: Convergence
3-2. CONVERGENCE • Movement of red, green and blue dots by V. STAT tilting and opening or closing. Purity 1 Movement of opening or closing the BMC magnet V. STAT convergence magnet. Vertical static convergence magnet Movement of tilting the V. STAT conver- gence magnet counterclockwise. -
Page 45: Focus Adjustment
• Adjust TLH. (TLH CORRECTION PIECE : 4-057-714-01) Correct horizontal mis-convergence of X axis' right and left red and blue. When red is outside and view from DY neck side, insert TLH correction piece to rightside (TLH+) and when blue is outside and also view from DY neck side, insert TLH a-d : screen-corner correction piece to left (TLH-). -
Page 46: White Barance Adjustment
3-5. WHITE BALANCE ADJUSTMENT 1. Receive color-bar signal and set menu picture quality to minimum picture and standard brightness. 2. Set to service mode and adjust CUT-OFF (VP25-green, VP26- blue) and DRIVE (22-green, VP23-blue) of center. 3. Switch to all white signal. 4. -
Page 47: Safety Related Adjustment
SECTION 4 SAFETY RELATED ADJUSTMENT CONFIRMATION OF HOLD-DOWN When the parts with a mark on the circuit diagram shown below are replaced, confirm the matters described in items 1. and 2. shown below. : PM601, R614, C614, IC607, R638 1. CONFIRMATION OF +B LINE (A BOARD) 3. -
Page 48: Circuit Adjustments
SECTION 5 CIRCUIT ADJUSTMENT 5-1. ADJUSTMENTS WITH COMMANDER 6. WRITING "STANDARD VALUE" 1. ENTERING SERVICE MODE 1) Set to service mode. 1) Turn on the main power of the set and enter into stand-by 2) When push 5 button on the remote commander green mode. -
Page 49: Adjustment Method
5-2. ADJUSTMENT METHOD Service adjustment to this model can be performed with the supplied Remote Control Commander RM-955, 956. • HOW TO ENTER INTO SERVICE MODE Entering the service mode When exchange When exchange When repair connect- the MEMORY ed with picture quality the board IC002 (MA10 board) Perform “standard... -
Page 50: Service Data
5-3. SERVICE DATA DISP DATA STANDARD ITEM DEVICE RANGE DATA 00-03 AFC LOOP GAIN SWITCHING CXA2130S VPOS 00-3F V POSITION (Y/C/J) VSIZ 00-3F V SIZE SCOR 00-0F S CORRECTION VLIN 00-0F V LINIARITY HPOS 00-3F HORIZONTAL POSITION HSIZ 00-3F H SIZE AFBW 00-0F AFC BOW... - Page 51 DISP DATA STANDARD ITEM DEVICE RANGE DATA 00-FF NICAM SEARCH DELAY 00-01 AGC SWITCH 00-3F AGC GAIN 00-01 CARRIER MUTING 00-01 AUDIO CLOCK OUT 00-7F 00-7F 00-7F 00-7F 00-7F NICAM PRESCALE MS10 00-FF AUTO-FM SWITCH THRESHOLD MS11 00-FF INTELLIGENT VOLUME DISP DATA STANDARD...
-
Page 52: A Board Adjustment
5-4. A BOARD ADJUSTMENT 1. H OSC ADJUSTMENT 1) Input select should be selected LINE input (no signal). 2) Connect a frequency counter to TP801 (A board). 3) Adjust service data "VP42" (HOSC) to become 15.690kHz ± 25Hz. 2. PICTURE QUALITY ADJUSTMENT 2-1. - Page 53 MEMO ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○...
- Page 54 MEMO ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○...
-
Page 55: Diagrams
SECTION 6 TV BLOCK DIAGRAMS 6-1. BLOCK DIAGRAMS TU101 CN304 CN703 200V +200V B INT TO JIG IC301 Y/C/J VIDEO BUFF BUFF V901 ONLY TV IN PICTURE TUBE Q101 Q305 IC701 R AMP CN305 CN701 V OUT V IN J701 IC103 KR H2 DC-DC CONV. -
Page 56: Printed Wiring Boards And Schematic Diagrams
– A BOARD – [TUNER, Y/C/J, HV DEFLECTION, POWER SUPPLY] 6-2. CIRCUIT BOARDS LOCATION A BOARD D305 D307 D308 IC101 C-4 D501 IC103 A-4 D502 IC301 E-2 D503 IC501 C-1 D506 IC601 E-7 D507 IC602 C-4 D601 Reference information IC603 D-7 D602 IC604 D-4 RESISTOR... - Page 57 ABOARD : IC103 TK11819M ABOARD : IC606 STR-F6614 V IN V IN MOTIVE CN303 START O.V.P LATCH DRIVE CN301 CN302 V OUT AUDIO VIDEO J101 TU101 TO MA10 BOARD(1/3) CN001 TO MA10 BOARD(1/3) CN1003 TO MA10 BOARD(1/3) CN002 REG. V REF FEEDBACK T.S.D CONTROL...
- Page 58 TO FBT CN704 D702 1SS199 TO A BOARD 1000V PROTECT T801(FBT) 200V C720 4700p RED.OUT D703 R738 1SS199 200V C709 100k 0.047 PROTECT J701 1/2W AC FILTER 200V .BLK019E L701 .BLK018C C719 C721 0.001 :EL0607 (RGB OUT,VM) IC701 G1-1 250V .BLK019A TDA6101Q/N3 R734...
-
Page 59: [ Video Section]
TABLE OF CONTENTS Section Title Page Section Title Page [ VIDEO SECTION] 5. DIAGRAMS 1. GENERAL 5-1. Block Diagrams ............81 1-1. INTERNAL VIEWS ..........72 5-2. Circuit Boards Location .......... 83 5-3. Printed Wiring Boards and Schematic Diagrams ..84 2. -
Page 60: General
SECTION 1 GENERAL 1-1. INTERNAL VIEWS Drum assembly DZH-89A-R 1-759-453-11 - Top Side - ACE block assembly A-6759-620-A FE head Pinch press block assembly 1-500-144-11 A-6759-615-A FL complete assembly A-6759-619-B Reel table (T) Reel table (S) 3-977-508-01 3-977-507-01 M902 - Bottom Side - Capstan motor 1-698-971-11 Timing belt... -
Page 61: Disassembly
SECTION 2 DISASSEMBLY 2-1. TOP COVER REMOVAL 2-2. VCR BLOCK ASSY REMOVAL 1 Four screws 3 Six screws (+BVTP 3 × 12) (+BVTP 3 × 12) RP earth plate 2 Top cover 4 VCR BLOCK assembly 1 CN701 2 Two screws (+BVTP 3 ×... -
Page 62: Circuit Adjustments
SECTION 3 CIRCUIT ADJUSTMENTS [ SET-UP FOR ADJUSTMENT ] Necessary items and indications for total adjustment of electric The video signal from the pattern generator is used as adjustment circuit of this unit will be described in this chapter. signal for electrical adjustment. This video signal should meet the requirement. - Page 63 X’tal OSC CHECK CARRIER DEVIATION CHECK Mode Mode Signal Alignment tape, Stair step Signal Color bar MA10 board IC802 !•pin Measurement Point MA10 board Q823 emitter(NTSC) Measurement Point IC802 %ªpin(PAL) Measurement Equipment Spectrum Analyzer Measurement Equipment Oscilloscope Specified Value =1.00±0.08MHz Specified Value 500±200mVp-p Check: Confirm f...
- Page 64 REC Y LEVEL CHECK PB Y LEVEL CHECK Mode E-E(SP) Mode Signal No signal Signal Color bar MA10 board IC802 !•pin Measurement Point Measurement Point MA10 board Q830 emitter Measurement Equipment Oscilloscope Measurement Equipment Oscilloscope Specified Value 240±70mVp-p(NTSC) Specified Value 1.0±0.1Vp-p 260±70mVp-p(PAL) Check: Confirm the Vp-p of the waneform is 1.0±0.1Vp-p.
-
Page 65: Μ-Com Port Function Description
SECTION 4 INTERFACE, IC PIN FUNCTION DESCRIPTION 4-1. µ-COM PORT FUNCTION DESCRIPTION (MA10 BOARD IC001) Pin No. Signal Function S SEL F S-INPUT SELECT (FRONT) S SEL R S-INPUT SELECT (REAR) TU STEREO MODE TU BILINGUAL MODE DGC SW – DGC ON/OFF CONTROL ST/ MONO SET MODE STEREO/MONO... -
Page 69: Diagrams
CN1003 SYSTEM CONTROL,MAIN MICON, MA10 D 5.8V SECTION 5 VCR SERVO,AUDIO OUT,Y/C PROCESS, CN1001 CN702 GND(A) AUDIO PROCESS,VIDEO•AFM REC/PB AMP GND(AV) SW 5V FULL ERASE RF SWP SW 9V CHECK HEAD V FM AMP V FM AMP FE HEAD DIAGRAMS CONNECTOR PB RF BUFF... -
Page 70: Printed Wiring Boards And Schematic Diagrams
– MA10 BOARD – MA10 (1/3) SYSTEM CONTROL, MAIN MICON VCR SERVO, AUDIO OUT MA10 (2/3) [ Y/C PROCESS ] 5-3. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS MA10 (3/3) Note: • All capacitors are in µF unless otherwise noted. pF: µµF [ VIDEO REC/PB AMP ] Capacitors without voltage indication are all 50V. - Page 71 CN1003 TO A BOARD CN302 IC201 VOLTAGE CN401 TDA7494 CN406 AUDIO OUT CN1004 MARK #-PARTS NOT USED FOR THIS MODEL. NO MARK:REC/PB TO DRUM MTR DEW SENSER FOR JIG ):REC SYSTEM CONTROL, MAIN MICON << >>: PB JR401 VCR SERVO,AUDIO OUT R204 :CHIP D407...
- Page 72 (Y/C PROCESS) GND(A) PB AL AUDIO(PB) TU AL TO MA10(1/3) SW 5V SW5V SW5V SW5V GND(A) SW5V PB V TU V VIDEO(PB) R1020 L1004 :CHIP R1027 R871 Q822 AUDIO(REC) SW5V AUDIO(REC) R872 R1026 R862 SW5V SW5V C1014 0.01 :CHIP R1017 F:CHIP 5.6k Q823...
- Page 73 CN702 VIDEO REC/PB AMP REC CUR PB RF C727 0.01 F:CHIP IC701 RF SWP HA118295NT VIDEO REC/PB AMP C723 JW444 C711 (1.8) R705 CN701 0.022 1.8k CHECK CN F:CHIP :CHIP F:CHIP HIFI CH2 JW445 C712 HIFI CH2 F C724 0.022 (3.6) (3.8) F:CHIP...
-
Page 74: Ma10 (3/3) Board
5-4.SEMICONDUCTORS FF10 BA10393F-E2 HA118295NT PQ05RD11 STR-F6656 [ LED, EJECT SW ] BA6305F-E2 -PQ09RD11 BA7755AF-E2 – FF10 BOARD – M24C16-MN6T NJM062M TOP VIEW 30pin DIP LA71504M-MPB PQ30RV11 S-80743AL-A7 TOP VIEW 8pin SOP CXA2089Q TOP VIEW LA7840L PST572C MARKING SIDE VIEW TOP VIEW TDA6101Q/N3 7pin SIP MARKING SIDE VIEW... - Page 75 TRANSISTOR DIODE 2SC5388 D1NL20U RPT-37PBT32 D6SB60LF RPT-37PB3F CATHODE ANODE D1NS4 EGP30D D1N20R 2SK1482-T UN2113 CATHODE MTZJ-T-77-3.9B UN2211 MTZJ-3.3 UN2213 MTZJ-5.1C 2SA1162-G MTZJ-6.2B 2SB709A-QRS-TX RD10ESB2 ANODE 2SC1623-L5L6 RD18ES-B2 2SC2412K-T-146-QR RD3.9ES-B1 2SD601A-Q RD3.9ES-B2 2SD601A-QRS-TX RD39ES-B2 RD5.1ES-B1 ERC04-06S RD5.6ESB2 ERC06-15S 2SK2251-01 RD6.8ES-B2 RU-1P 1SS119-25 CATHODE 11ES2...
-
Page 76: Exploded Views
SECTION 6 EXPLODED VIEWS The components identified by shading and mark are criti- NOTE: cal for safety. • The construction parts of an assembled part are Replace only with part number indicated with a collation number in the remark • Items with no part number and no description are specified. -
Page 77: Chassis
The components identified by 6-2. CHASSIS shading and mark are criti- cal for safety. Replace only with part number : 7-685-648-79 +BVTP 3X12 specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- -------------... -
Page 78: Mechanism Deck Assembly (1)
6-3. MECHANISM DECK ASSEMBLY (1) : 7-685-646-79 +BVTP 3X8 REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- ------------- 3-977-509-01 WASHER, THRUST 3-977-447-01 GEAR, ELEVATOR 3-977-507-01 TABLE, REEL (S) 3-977-514-01 OPENER, LID 3-977-508-01 TABLE, REEL (T) 3-977-441-01 GEAR, PINCH PRESSING 1-500-471-11 HEAD, FE... -
Page 79: Mechanism Deck Assembly (2)
6-4. MECHANISM DECK ASSEMBLY (2) : 7-685-646-79 +BVTP 3X8 : 7-682-547-04 +P 3X6 262 263 REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- ------------- X-3947-581-4 BRAKE ASSY,MAIN(T) A-6750-324-A SHUTTLE (S) BLOCK ASSY 262,263 3-977-462-01 SPRING,EXTENTION. -
Page 80: Mechanism Deck Assembly (3)
6-5. MECHANISM DECK ASSEMBLY (3) : 7-685-646-79 +BVTP 3X8 : 7-685-133-19 +BVTP 2.6 REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- ------------- 3-977-437-01 RETAINER,CAM MOTOR 3-977-455-01 GEAR, LOADING(T) X-3947-584-1 ASSY, REEL DIRECT 3-977-456-03 SPRING, TORSION (LOAD T) 3-977-443-01 WASHER, STOPPER 3-977-438-01 WORM - WHEEL... -
Page 81: Electrical Parts List
The components identified by SECTION 7 shading and mark are criti- cal for safety. ELECTRICAL PARTS LIST Replace only with part number specified. NOTE: • The components identified by in this manual have been When indicating parts by reference number, REF. - Page 82 The components identified by shading and mark are criti- cal for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- ------------- C625 1-126-972-11 ELECT\T1000MF 20% C828 1-126-960-11...
- Page 83 The components identified by shading and mark are criti- • The components identified by in this manual have been cal for safety. carefully factory-selected for each set in order to satisfy Replace only with part number regulations regarding X-ray radiation. Should replacement be specified.
- Page 84 The components identified by shading and mark are criti- • The components identified by in this manual have been cal for safety. carefully factory-selected for each set in order to satisfy Replace only with part number regulations regarding X-ray radiation. Should replacement be specified.
- Page 85 The components identified by shading and mark are criti- • The components identified by in this manual have been cal for safety. carefully factory-selected for each set in order to satisfy Replace only with part number regulations regarding X-ray radiation. Should replacement be specified.
- Page 86 The components identified by shading and mark are criti- cal for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- ------------- X301 1-567-504-11 OSCILLATOR, CRYSTAL D714 8-719-911-19...
- Page 87 The components identified by shading and mark are criti- cal for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- ------------- * A-1241-367-A F BOARD MOUNTED ******************* 1-533-223-11 CLIP, FUSE...
- Page 88 The components identified by shading and mark are criti- cal for safety. Replace only with part number FF10 MA10 VIDEO BLOCK specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- ------------- * A-1241-368-A FF10 BOARD MOUNTED...
- Page 89 The components identified by shading and mark are criti- cal for safety. Replace only with part number MA10 specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- ------------- C418 1-130-488-00 MYLAR\T0.027MF 5% C720...
- Page 90 The components identified by shading and mark are criti- cal for safety. Replace only with part number MA10 MA10 specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- ------------- C834 1-163-038-91 CERAMIC CHIP\T0.1MF...
- Page 91 The components identified by shading and mark are criti- cal for safety. Replace only with part number MA10 MA10 specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- ------------- C1015 1-126-960-11 ELECT\T1MF...
- Page 92 The components identified by shading and mark are criti- cal for safety. Replace only with part number MA10 specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- ------------- JR107 1-216-295-91 SHORT L811...
- Page 93 The components identified by shading and mark are criti- cal for safety. Replace only with part number MA10 specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- ------------- R005 1-216-089-91 RES,CHIP 1/10W...
- Page 94 The components identified by shading and mark are criti- cal for safety. Replace only with part number MA10 specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- ------------- R068 1-216-041-00 RES,CHIP 1/10W...
- Page 95 The components identified by shading and mark are criti- cal for safety. Replace only with part number MA10 specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- ------------- R436 1-216-043-91 RES,CHIP 1/10W...
- Page 96 The components identified by shading and mark are criti- cal for safety. Replace only with part number MA10 specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- ------------- R810 1-216-041-00 RES,CHIP 1/10W...
- Page 97 The components identified by shading and mark are criti- cal for safety. Replace only with part number MA10 specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK ------------ ------------- ------------------- ------------- ------------ ------------- ------------------- ------------- R926 1-216-025-91 RES,CHIP 1/10W...
- Page 98 BAG, PROTECTION * 4-073-513-01 INDIVIDUAL CARTON * 4-073-514-01 CUSHION (UPPER) (ASSY) * 4-073-515-01 CUSHION (LOWER) (ASSY) ****************************************************************** Sony Corporation English 99KM70177-1 Sony Technology (Malaysia) Sdn. Bhd. Printed in Malaysia © 9-965-780-01 TV Business of General Area 1999. 11 – 122 –...