HALE HP 100 Operation And Maintenance Manual

Hp series portable pump

Table of Contents

Quick Links

1/8/04

WARNING

A Hale Pump is a quality product: ruggedly designed, accurately machined, carefully assembled and thoroughly tested. In

order to maintain the high quality of your pump, and to keep it in a ready condition, it is important to follow the instructions on

care and operation. Proper use and good preventive maintenance will lengthen the life of your pump.

ALWAYS INCLUDE THE PUMP SERIAL NUMBER IN CORRESPONDENCE.

HALE PRODUCTS, INC.

A Unit of IDEX Corporation

Class 1

607 NW 27th Avenue

HP SERIES

PORTABLE PUMPS

USER OPERATION AND

MAINTENANCE MANUAL

Pump

Serial

Number

Failure to follow the operating, lubrication, and maintenance

requirements set forth in this operating and maintenance manual

may result in serious personal injury and/or damage to equipment.

700 Spring Mill Avenue

Ocala FL 34475 USA Tel: 352-629-5020 800-533-3569 Fax: 352-629-2902

Hale Products cannot assume responsibility for product failure resulting from improper

maintenance or operation. Hale Products is responsible only to the limits stated in the product

warranty. Product specifications contained in this material are subject to change without notice.

Conshohocken, PA 19428

TEL: 610-825-6300

FAX: 610-825-6440

www.class1.com

Table of Contents

Summary of Contents for HALE HP 100

Page 1 A Hale Pump is a quality product: ruggedly designed, accurately machined, carefully assembled and thoroughly tested. In order to maintain the high quality of your pump, and to keep it in a ready condition, it is important to follow the instructions on care and operation.
Page 2 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE...
Page 3 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE Table of Contents SAFETY....................... 5 EQUIPMENT DESCRIPTION ............... 8 OPERATING CONTROL DESCRIPTION ........... 14 INITIAL CHECKOUT PROCEDURES ............18 STARTING PROCEDURES ................ 24 SHUTDOWN AND STORAGE PROCEDURES ......... 26 MAINTENANCE SCHEDULE ..............28 PUMP MAINTENANCE ................
Page 4 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE...
Page 5: Safety
HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE SAFETY THIS SYMBOL MEANS WARNING PERSONAL INJURY MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY. WARNING 8. DO NOT STORE, SPILL, OR USE 1. DO NOT run engine in an enclosed GASOLINE NEAR AN OPEN FLAME, or area.
Page 6 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE pressure of 7 BAR (100 PSIG). Under 5. DO NOT touch hot mufflers, normal operation conditions these cylinders, or fins as contact may cause pumps may not provide the required burns. pressure to use these nozzles properly. When selecting a pump and nozzle 6.
Page 7 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE 13. Petroleum solvents, such as kerosene, are not to be used to clean cartridge. They may cause deterioration of the cartridge. DO NOT OIL CARTRIDGE. DO NOT USE PRESSURIZED AIR TO CLEAN OR DRY CARTRIDGE.
Page 8: Equipment Description
HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE EQUIPMENT DESCRIPTION The HP Series Portable Pump line stainless steel clamp. The pump engine provides emergency services personnel is air cooled and the portable models around the world with portable pumps are enclosed with high strength to fulfill many types of in-service thermoplastic covers that ensure a applications.
Page 9 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE four folding handles. Other than the Each pump is powered by a reliable stowed position there are two other state-of-the-art air cooled, 18 HP, V-twin, positions of the handles to provide for Overhead Valve (OHV) engine.
Page 10 The following figure obtained from that specific pump shows the serial number tag. model. All the tests were conducted at sea level. HALE PRODUCTS, INC NOTICE Performance of HP Series pumps meets or exceeds NFPA1921 requirements. For complete NFPA1921...
Page 11 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE Hale Products, Inc. Hale Fire Pump Company Conshohocken, Pa. 19428 USA INLET: 2 IN UNIT MODEL : HP100 OUTLET: 1-1/ 2 IN ENGINE: LIFT: 4 FT BRIGGS & STRATTON MODEL ELEVATION: SEA-LEVEL...
Page 12 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE Hale Products, Inc. Hale Fire Pump Company Conshohocken, Pa. 19428 USA INLET: 3 IN UNIT MODEL : HP300 OUTLET: 2-1/2 IN ENGINE: LIFT: 4 FT BRIGGS & STRATTON MODEL ELEVATION: SEA-LEVEL VANGUARD 18 OHV...
Page 13 2-1/2 in. ISO Female 2-1/2 in.ISO Female 2-1/2 in. NPT Female 3 in. NPT Female 3 in. NPT Female HP "X" SERIES 1-1/2 in. NPT Female (Hale 115 Flange) (Hale 115 Flange) (Hale 115 Flange) BODY ALUMINUM ALUMINUM ALUMINUM ALUMINUM...
Page 14: Operating Control Description
HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE OPERATING CONTROL DESCRIPTION Most of the controls and indicators necessary for the operation of the pump 2. MASTER SWITCH: The Master are located on the operator panel. switch is located below the start The pump operator should become button and is used to close the thoroughly familiar with the location and...
Page 15 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE the handle must be held in the down 0.2-0.4 kg/cm (4-6 PSIG). If the light position until the pump is primed. should light during normal operation Once the pump is primed and the operator must shutdown the pressure is showing on the discharge engine immediately to avoid engine...
Page 16 11. PUMP DRAIN: The pump drain is a (Hale P/N 200-2100-02-0). The socket petcock type valve located below is also used to plug in the optional...
Page 17 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE operated with a positive pressure source the valve must be closed to prevent water from being blown out of the exhaust pipe. EXHAUST PRIMER VALVE ASSEMBLY 1/4 TURN BALL VALVE (SHOWN IN NORMAL OPERATING POSITION) EXHAUST PRIMER ASSEMBLY...
Page 18: Initial Checkout Procedures
HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE INITIAL CHECKOUT PROCEDURES Upon receipt of the pump from the battery to its holder and clamp in place. factory remove the pump and all CAUTION: Always connect accessories from the shipping container the black wire to the negative and check for damage.
Page 19 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE isolated. When making the Insert the bolts and secure in place with permanent connections to the lockwashers and nuts provided. suction and discharge fittings DO NOT use hard piping. A 4. When the pump is mounted and if short length of flexible piping is required to prevent damage access is not provided to fill the fuel tank...
Page 20 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE making discharge piping connection. SUCTION GAUGE f. After the discharge connection is TUBING CONNECTION complete tighten the "V"-band clamp to prevent leakage. 8. Connect the exhaust priming lever cable to the exhaust primer. DISCHARGE GAUGE TUBING CONNECTION EXHAUST PRIMER...
Page 21 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE operation the following items must be checked. WARNING: DO NOT smoke when filling fuel tank. WARNING: DO NOT fill fuel FUEL FILLER CAP tank while engine is running. Allow engine to cool for two minutes before refueling.
Page 22 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE engine crankcase. Before pump into operation for the placing pump into operation first time fill gearbox to proper for the first time fill engine level with SAE 30 Weight crankcase to proper level with Detergent oil.
Page 23 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE 6. CONNECT DISCHARGE HOSE: After connecting discharge hose ensure the discharge valve is closed. Remove all kinks and sharp bends from the discharge hose. 7. CLOSE PUMP DRAINS: Make sure the pump and discharge valve drains are closed.
Page 24: Starting Procedures
HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE STARTING PROCEDURES The following procedures will be indicates the battery is good and the pump is ready to start. If the oil light is followed to start the pump and establish not lit check the battery connections water flow.
Page 25 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE to obtain the desired discharge pressure For the "I" version, turn the key switch on the discharge gauge. CAUTION: Exhaust system and release when the pump has started. components may smoke during the initial break-in period.
Page 26: Shutdown And Storage Procedures
HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE SHUTDOWN AND STORAGE PROCEDURES To enhance pump life the following 2. ENERGIZE PUMP: Start engine and procedures shall be used when shutting establish water flow through pump. down the pump. 3. FLUSH PUMP: Run pump for 2 minutes 1.
Page 27 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE Also, wipe the pump covers down with a clean damp cloth. If necessary use a mild soap and water solution to clean plastic covers. 10. STORE PUMP: Return pump to storage compartment and secure in place.
Page 28: Maintenance Schedule
HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE MAINTENANCE SCHEDULE MAINTENANCE INTERVALS To prolong pump life and ensure reliable operation the pump user shall perform the maintenance described in the following section on a regular basis. The table that follows provides a listing of the minimum maintenance intervals. Following the chart are detailed maintenance procedures.
Page 29: Pump Maintenance
HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE PUMP MAINTENANCE The HP Series portable pumps are OIL FILL FITTING designed to provide years of reliable service with a minimum of maintenance OIL LEVEL PLUG on the pump end. The pump must be cleaned and flushed out after each use.
Page 30 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE 5. Replace oil fill fitting and vent. 6. Remove oil level plug from gearbox. 6. Return pump to storage or operation. 7. Place funnel in oil fill fitting and slowly pour oil into gearbox until oil CHANGE GEARBOX OIL (HP100) starts to flow from the oil level hole.
Page 31 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE WARNING: TO PREVENT 8. Using wire brush and tip cleaners ACCIDENTAL STARTING when carefully remove carbon from ejector servicing the engine or pump nozzle and check valve assembly. always disconnect the negative wire from battery terminal.
Page 32: Engine Maintenance
HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE ENGINE MAINTENANCE General lnformation This is a twin cylinder, overhead valve, air cooled engine. All drilled/tapped holes and fasteners on this engine are ISO metric. however, where equipment attaches to engine, SAE standards apply. WARNING: TO PREVENT 7.
Page 33 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE 3. The oil drain fitting is a hex fitting with a pipe plug. Use adjustable wrench to hold hex fitting while removing the pipe plug with an allen wrench. TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE 4.
Page 34 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE check oil level. Refill crankcase as Replace the oil filter using the following necessary. procedures: 9. Check area around pump for oil 1. Place the pump assembly in a leaks. work area where access can be made to the oil drain fitting.
Page 35 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE NOTE: Before installing new 13. Check area around pump for oil filter, lightly oil filter gasket with leaks. fresh clean engine oil. 14. Return pump to storage area. 7. Oil the filter gasket and screw the new oil filter on by hand until gasket DUAL ELEMENT AIR CLEANER contacts filter adapter then tighten...
Page 36 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE cartridge air dry thoroughly before 3. Remove nut holding retainer using. plate, cartridge and foam pre- cleaner to top of engine. CAUTION: Petroleum solvents, 4. Remove retainer plate and foam such as kerosene, are not to pre-cleaner from cartridge.
Page 37 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE 7. Reinstall pre-cleaner and retainer ring on cartridge. 8. Reinstall foam pre-cleaner, cartridge and retainer plate assembly in air cleaner housing on top of engine. Secure in place with nut. 9. Reinstall air cleaner cover on top of pump and latch in place.
Page 38 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE this assembly every 50 hours of pump operation or monthly for cleaning and 3. Disconnect primer tubing and inspection. primer control cable as necessary. WARNING: TO PREVENT 4. Remove the three bolts that hold ACCIDENTAL STARTING when the exhaust primer assembly on the servicing the engine or pump...
Page 39 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE Spark Plug Type Champion Autolite 13. Return pump to storage or Resistor RC12YC 3924 operation. Spark Plug Gap ....76 mm (.030 in.) REPLACE SPARK PLUGS 5. Obtain new spark plug and check Replace the spark plugs every 100 hours gap using a wire gauge.
Page 40 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE 3. Using pliers remove clips holding REPLACE FUEL FILTER the fuel filter in the fuel line. A clogged or dirty fuel filter can adversely affect engine performance. 4. Place a container under the fuel The fuel filter should be replaced each filter to catch any excess fuel that year or more often as engine...
Page 41 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE 4. Connect battery load test POS BATTERY TERMINAL instrument to the terminals and place battery under simulated starting load CELL CAPS with the test instrument. The meter should read 9 volts or more when the simulated starting load is applied.
Page 42: Warranty Policy
Hale or its designee. Items not manufactured by Hale shall bear only the limited warranties offered by their respective manufacturers.
Page 43: Mounting Dimensions
HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE MOUNTING DIMENSIONS "X" SERIES PUMP MOUNTING DRAWINGS The following pages contain drawings to assist in the mounting of "X" Series pumps on apparatus. The drawings are not to scale but will assist the installer in locating mounting holes for the pumps.
Page 44 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE "X" Series Pump Mounting Dimensions...
Page 45 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE "X" Series Pump Base Mounting Hole Location Dimensions...
Page 46 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE "X" Series Pump Control Panel Mounting Hole Location Dimensions...
Page 47 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE "I" SERIES PUMP MOUNTING DRAWINGS The following pages contain drawings to assist in the installation of "I" Series pumps on apparatus. The drawings are not to scale but will assist the installer in locating mounting holes and determining compartment size for the pumps.
Page 48 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE "I" Series Pump Dimensions...
Page 49 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE ELECTRICAL WIRING DIAGRAMS HP and HP"X" Series Electrical Wiring Diagram...
Page 50 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE HP"I" Series Electrical Wiring Diagram...
Page 51: Parts List
Series pumps. Each part of the pump is identified on the illustration with an index number. Located in the list on the page next to the illustration are the Hale Products Inc. part numbers for the component parts. When repairing the pump refer to these exploded views to identify the part numbers of components requiring replacement.
Page 52 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE PL-1: HP SERIES PUMP COMPONENT IDENTIFICATION...
Page 53 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE PL-1: HP SERIES PUMP COMPONENT IDENTIFICATION ITEM PART NUMBER DESCRIPTION QTY UNIT 545-4050-00-0 HP100 PORTABLE PUMP 545-4050-02-0 HP100X PORTABLE PUMP 545-4060-00-0 HP200 PORTABLE PUMP 545-4060-02-0 HP200X PORTABLE PUMP 545-4070-00-0 HP300 PORTABLE PUMP 545-4070-02-0 HP300X PORTABLE PUMP 545-4080-00-0...
Page 54 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE 4.5 N-m (40 lb-in) 2.3 N-m (20 lb-in) PL-2: HP SERIES PORTABLE PUMP COVERS AND CARRYING HANDLES...
Page 55 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE HP SERIES PORTABLE PUMP COVERS AND CARRYING HANDLES ITEM PART NUMBER DESCRIPTION QTY UNIT 064-6320-01-0 HINGE/RELEASE PIN 070-0020-24-0 PORTABLE PUMP COVER 200-2090-04-0 LIGHT MAST/CHARGING SOCKET 070-0030-28-0 PORTABLE PUMP SIDE PANEL 070-0030-31-0 PORTABLE PUMP SIDE PANEL 242-0250-01-0 SIDE PANEL SWELL LATCH 218-0406-48-0...
Page 56 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE...
Page 57 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE HP200, HP300 AND HP400 PUMP END ITEM PART NUMBER DESCRIPTION QTY UNIT 604-0079-00-0 1/4 ODX.040 THERMOPLASTIC TUBING 082-0262-11-0 CONNECTOR-1/4 NPT X 1/4 TUBE PLTD 082-0261-11-0 ELBOW 1/4 MNPT X 1/4 TUBE, PUSH 210-1000-02-0 5504-1000 NUT M-10 X 1.5 097-1070-00-0...
Page 58 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE NOTE: Items 1 through 16 are not provided with "X" Series pump. PL-4: HP100 PUMP END AND GEARBOX ITEM PART NUMBER DESCRIPTION QTY UNIT 018-8250-00-0 STUD-HP SERIES VALVE STOP M8 538-1450-01-0 HP100 DISCHARGE VALVE ASSEMBLY 218-0408-19-0 SCREW M4-.7X16 SOC.HD.
Page 59 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE HP100 PUMP END AND GEARBOX ITEM PART NUMBER DESCRIPTION QTY UNIT 041-0480-00-0 HP SERIES VALVE STEM 041-0470-00-0 HP SERIES VALVE SHAFT 040-2100-00-0 2308-210 O-RING 038-1220-01-0 1/8 DRAIN VALVE-PLTD BRASS 097-1840-00-0 2 INCH ISO(BSP) SEAL WASHER 038-1600-00-0 HP100 DISCHARGE VALVE BODY 040-2250-00-0...
Page 60 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE PL-5: HP400 DISCHARGE MANIFOLD...
Page 61 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE HP400 DISCHARGE MANIFOLD ITEM PART NUMBER DESCRIPTION QTY UNIT 018-8250-00-0 STUD-HP SERIES VALVE STOP M8 218-0408-19-0 SCREW M4-.7X16 SOC.HD. LOCK 012-0170-02-0 HANDWHEEL-HP SERIES DISCHARGE 210-0805-11-0 NUT M8-1.25 STNLS STL LOCKING 097-1750-01-0 HP300 VALVE WASHER 097-1760-00-0 HP300 VALVE SEAL WASHER 097-1750-00-0...
Page 62 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE PL-6: HP300 DISCHARGE VALVE ASSEMBLY...
Page 63 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE HP300 DISCHARGE VALVE ASSEMBLY ITEM PART NUMBER DESCRIPTION QTY UNIT 018-8250-00-0 STUD-HP SERIES VALVE STOP M8 218-0408-19-0 SCREW M4-.7X16 SOC.HD. LOCK 012-0170-02-0 HANDWHEEL-HP SERIES DISCHARGE 210-0805-11-0 NUT M8-1.25 STNLS STL LOCKING 097-1750-01-0 HP300 VALVE WASHER 097-1760-00-0 HP300 VALVE SEAL WASHER...
Page 64 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE PL-7: HP SERIES PUMP EXHAUST PRIMER ASSEMBLY...
Page 65 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE HP SERIES PUMP EXHAUST PRIMER ASSEMBLY ITEM PART NUMBER DESCRIPTION QTY UNIT 604-0033-00-0 3/8 OD X.032 WALL COPPER TUBE 082-0206-02-0 CONNECTOR-1/4NPT TO 3/8 TUBING 038-1130-00-0 1/4 NPT FEMALE BALL VALVE 082-0212-02-0 NIPPLE-1/4 NPT PLTD BRS 38 MM (1.5 IN.) LG 3.0 082-0215-02-0 COUPLING 1/4 NPT BRASS 276-0230-00-0...
Page 66 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE SERIAL NUMBER NAMEPLATE PL-8: HP SERIES PUMP ENGINE MOUNTING...
Page 67 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE HP SERIES PUMP ENGINE MOUNTING ITEM PART NUMBER DESCRIPTION QTY UNIT 210-0805-11-0 NUT M8-1.25 SST LOCK 097-1850-00-0 WASHER-.34ID X 1.13OD X .091 12.0 048-0800-01-0 VIBRATION MOUNT BUSHING 108-0560-00-0 FUEL TANK PORTABLE PUMP 210-0805-11-0 NUT M8-1.25 SST 218-0822-02-0...
Page 68 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE PL-9: INSTRUMENT PANEL ASSEMBLY ITEM PART NUMBER DESCRIPTION QTY UNIT 019-0320-64-0 INSTRUMENT PANEL SUPPORT PLATE 019-0320-63-0 INSTRUMENT PANEL PLATE 513-0230-00-0 CHOKE CONTROL-18.25" LONG (HP PORTABLE SERIES) 513-0230-01-0 CHOKE CONTROL-77.5" LONG (HP X-SERIES) 200-0540-11-0 RED LIGHT ASSY 200-0540-02-0...
Page 69 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE PL-10: FUEL VENT AND PICK-UP ASSEMBLY ITEM PART NUMBER DESCRIPTION QTY UNIT 044-0260-02-0 1/8 AIR VENT-NO CHECK 019-0560-06-0 FUEL VENT COUPLING BRACKET 082-0110-00-0 COUPLING 1/8 NPT STEEL 082-0118-02-0 ELBOW-1/8 NPT TO 1/4 ID HOSE 340-0060-02-0 1/4 ID FUEL HOSE 242-0620-01-0...
Page 70 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE PL-11: OIL FILTER AND DRAIN ASSEMBLY ITEM PART NUMBER DESCRIPTION QTY UNIT BAS-491056 OIL FILTER BAS-491657 OIL PRESSURE SWITCH 218-0608-19-0 SCREW M6-1 X 16 SOC. HD. SST LOCK BAS-805449 WASHER BAS-805292 OIL FILTER HOLDER 046-6600-00-0 GASKET-HP SERIES OIL FILTER 005-1150-00-0...
Page 71 HP SERIES PORTABLE PUMPS USER OPERATION AND MAINTENANCE PL-12: HP "X" SERIES MOUNTING HARDWARE ITEM PART NUMBER DESCRIPTION QTY UNIT 210-0805-11-0 NUT M8-1.25 STNLS STL LOCKING 12.0 097-1850-00-0 WASHER 1.13 OD X 0.34 ID X 0.091 IN. THK ZINC PLTD STL 218-0850-12-0 SCREW M8-1.25 X 100 H.H.ZINC PL 097-0520-00-0...

This manual is also suitable for:

H p200 Hp300