Operating Video Equipment (Continued); Operating A Cable Box Or Dbs Receiver - Sony KP-53XBR200 Service Manual

Operating Video Equipment (continued)

MDP manufacturer code numbers
Manufacturer
Sony
Panasonic
Pioneer
DVD Player manufacturer code
numbers
Manufacturer
Sony
Panasonic
Pioneer
RCA
Toshiba
Tips z
• In some rare cases, you may not be able to operate your
non-Sony video equipment with the supplied remote
control. In this case, please use the equipment's own
remote control.
• When you remove the batteries, the code number may
revert to the factory setting.
To operate video equipment
1
Set the VTR1/2/3/DVD/MDP switch to
the position through which you would
like to access the video equipment.
2
Use the VCR/DVD/MDP buttons
indicated in the following tables.

Operating a Cable Box or DBS Receiver

Setting the Manufacturer's
Code
You can program the supplied remote
control to operate a cable box or DBS
receiver.
Press CODE SET, DBS/CABLE
(FUNCTION), the 0-9 buttons to enter the
manufacturer's code number (see the
following chart), then press ENTER.
For example, to operate a Sony DBS receiver:
FUNCTION
CODE SET DBS/CABLE
8 0
Manufacturer code numbers
(cable box)
Manufacturer
Gemini
222, 223, 224, 225, 226
Hamlin/Regal
201, 202, 203, 204, 205,
Jerrold/G. I.
222, 206, 207, 208, 218
Macom
Magnavox
Oak
Panasonic
Philips 236, 237, 238, 239, 240, 241
Pioneer
Samsung
Scientific Atlanta
Tocom
Zenith
5 4
Operating a VCR using the remote control
Code To turn On/Off
701
To select a channel
704
702 To change channels
To record
To play
To stop
Code
To fast forward
751
To rewind the tape
753
To pause
752
755
To search the
754
picture forward or
backward
To change input
mode
Operating an MDP using the remote control
To turn On/Off
To play
To stop
To pause
Manufacturer code numbers
(DBS receiver)
Manufacturer
Sony
General Electric
RCA/PROSCAN
To operate the projection TV
Press TV (FUNCTION). Then use the
projection TV control buttons to control the
ENTER
1
projection TV.
For more details on operating the
cable box or DBS receiver
Refer to the operating instructions that come
Code
with the equipment.
233
If the remote control doesn't work
• Try repeating the set up procedures using
the other codes listed for your equipment.
230, 231, 232
234
227, 228, 229
219, 220, 221
214, 215
235
209, 210, 211
216, 217
212, 213
To search the picture
forward or backward
Press DVD/VTR (POWER).
[Green Button]
To search a chapter
Press the 0 – 9 buttons.
forward or backward
Press CH +/–.
Press (REC) while
Operating a DVD Player using the remote
pressing (lower).
control
Press (.
To turn On/Off
Press p.
Press ).
To play
Press 0.
To stop
Press P. Press again to
To pause
resume normal playback.
Press ) or 0 during
To step through
playback. Release to
different tracks of
resume normal playback.
an audio disc
Press TV/VTR.
To step through
different chapters
of a video disc
To display the Title
menu
Press DVD/VTR (POWER).
[Green Button]
To display the DVD
menu
Press (.
Press p. To select tracks
directly
Press P. Press again to
To display the
resume normal playback.
menu (Set up)
Tips z
• If more than one code number is listed, try entering
Code number
801 (preset code for
• If you enter a new code number, the code number you
remote control)
802
• In some rare cases, you may not be able to operate
802
• Whenever you remove the batteries — to replace
– 33 –
Press ) or 0 during
playback. Release to resume
normal playback.
Press CH +/–.
Press DVD/VTR (POWER).
[Green Button]
Press (.
Press p.
Press P. Press again to
resume normal playback.
Press ) to step forward or
0 to step backward.
Press CH+ to step forward or
CH– to step backward.
Press TITLE.
Press DVD MENU.
Press 0-9 buttons.
Press MENU.
them one by one until you come to the correct code for
your equipment.
previously entered at that setting is erased.
your equipment with the supplied remote control. In
this case, use the equipment's own remote control
unit.
them, for example — if too much time is taken, the
code numbers may revert to the factory setting and
must be reset.
5 3