Event/Alarm Display - JVC BR-HD50 Instruction Manual

ON-SCREEN DISPLAY

Event/Alarm display

Event display : When certain functions are in use, it is displayed at the following posi-
tions (with the DISPLAY mode ON or AUTO).
D V 2 K C H – 1 / 2 3 S P 2 m i n 0
A
B L A N K S E A R C H
B
I N D E X D E T E C T E D
S T A N D B Y - O F F
0 6 / 1 0 / 0 5
1 1 : 2 0 : 0 0 T C R 0 2 : 0 0 : 0 0 : 0 0
Alarm display : An alarm message is displayed at the following positions when there has
been an operation error or when BR-HD50 is not in good condition, e.g.,
dirty head.
D V 2 K C H – 1 / 2 3
A
H E A D C L E A N I N G R E Q U I R E D !
B
0 6 / 1 0 / 0 5
1 1 : 2 0 : 0 0
"A" display: The state of BR-HD50 is displayed. It continues to be displayed until the error state is
corrected. This display is not affected by the setting of the display mode.
Display
LOW VOLTAGE The voltage of the DC power source is low. If the operation continues, it enters
the OPERATE OFF mode.
HEAD CLEANING The video head is dirty. Clean it with the head-cleaning tape exclusively for BR-
REQUIRED! HD50. (XPage 9)
If the head is clogged, it is detected in the PLAYBACK mode and this message is
displayed.
OVERHEATING! The temperature inside BR-HD50 has exceeded the stated value.
Disconnect the power and place it at a cool place. If this message is displayed
again, BR-HD50 could be defective.
Consult your JVC-authorized service agent.
E-24
"A" display: displayed during operation
Display Description
BLANK Blank search in progress.
SEARCH
INDEX +1 Index search in progress.
The number indicates the
index search position.
INDEX MARK When an index has been
specified on the tape during
recording.
"B" display: displayed for about 3 seconds
Display Description
INDEX An index has been detected
DETECTED during index repeat operation.
VIDEO END The video end has been
DETECTED detected during end repeat
operation.
m i n
S P 2 0
N O H D V D / V S I G N A L
S T A N D B Y - O F F
T C R 0 2 : 0 0 : 0 0 : 0 0
Description
"B" display: Messages for incorrect operation are displayed for about 3 seconds.
They are displayed when the DISPLAY mode is ON or AUTO.
Display
INVALID TAPE! Data tape for PCs or DVC PRO tape is used.
The cassette tape will be automatically ejected.
LP TAPE! The user attempted to play back a tape recorded in the LP mode.
BR-HD50 cannot record or play in the LP mode.
NO HDV/DV SIG- The user attempted to record without HDV or DV signal input.
NAL
COPY INHIBIT The user attempted to record copy-guarded signals.
REC INHIBIT The user attempted to record on a tape that is not ready for recording (the rear
switch is set to SAVE).
OPERATION This message is displayed when an operation button is pressed with OPERAION
LOCK LOCK enabled. To enable OPERATION LOCK, set OPERATION LOCK in the
SYSTEM [2/2] Menu screen to ON.
PB INHIBIT This message is displayed when the HD/SD signal format setting differs during
[60/50] playback of a tape recorded in HDV/DV format.
REC INHIBIT • (for U model)
[60/50] This message is displayed when the unit is recorded in PAL mode.
• (for E model)
This message is displayed when the unit is recorded in NTSC mode.
50/25 INHIBIT • When 60/50 SEL in the SYSTEM [2/2] Menu screen is set to 60, this message
is displayed when HDV signal format is not 60Hz.
• This message is displayed when the DV signal from the IEEE1394 terminal is
not NTSC.
60/30 INHIBIT • When 60/50 SEL in the SYSTEM [2/2] Menu screen is set to 50, this message
is displayed when HDV signal format is not 50Hz.
• This message is displayed when the DV signal from the IEEE1394 terminal is
not PAL.
Description
E-25