Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes.
CFL Reflector edge softly. Otherwise the TFT Module may be damaged. (10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate or tilt the Interface Connector of the TFT Module. Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 5
(14) The LCD module is designed so that the CCFL in it is supplied by a Limited Current Circuit (IEC60950 or UL1950). Do not connect the CCFL to a Hazardous Voltage Circuit. Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 6
“Mura”. Take out the monitor with cushions Taking out the monitor by grasping the LCD panel.That will probably cause “Mura”. Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 7
Placing the monitor on foreign objects. foam pad. That will probably scratch the surface of the panel or cause “Mura.” The panel is placed facedown on the lap. That will probably cause “Mura.” Confidential ViewSonic Corporation D o Not Copy V P730/b...
Not compatible with interlaced video Horizontal / Vertical Frequency Horizontal Frequency 24 – 82 kHz Vertical Refresh Rate 50 – 85 Hz Maximum Pixel Clock 135 MHz Sync Polarity Independent of sync polarity Confidential ViewSonic Corporation D o Not Copy V P730/b...
1024 x 768 @ 50 Hz, 39.6 KHz 1024 x 768 @ 60 Hz, 48.4 KHz 1024 x 768 @ 70 Hz, 56.5 KHz 1024 x 768 @ 72 Hz, 58.1 KHz Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 10
1280 x 1024 @ 60 Hz, 64.0 KHz 1280 x 1024 @ 75 Hz, 80.0 KHz User Presets Number of User Presets (recognized timings) Available: 10 presets total in FIFO configuration Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 11
Typical= 8 ms (Tr= 6 ms, Tf = 2 ms) 10%-90% @ Ta=25°C Maximun =13 ms (Tr= 9 ms, Tf = 4 ms) 3.0 mg per lamp Mercury Panel Defects Please see Panel Quality Specifications. Confidential ViewSonic Corporation D o Not Copy V P730/b...
Tilt Up ¡Ù 20º Tilt Down From 0º down to -3º ~ -5 º Swivel Right ¡Ù 135º Swivel Left ¡Ù 135º Height Adjust ¡Ù 135 mm Pivot 0~90 degress (clockwise) Confidential ViewSonic Corporation D o Not Copy V P730/b...
3. Front Panel Function Control Description 3.1 Location of Controls Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 14
Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 15
Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 16
Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 17
Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 18
Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 19
No signal + [PW] +[2] + Burning mode Main Power on Signal + [PW] +[2] + Main Factory Mode Power on Remark : All the short cuts function are only available while OSD off Confidential ViewSonic Corporation D o Not Copy V P730/b...
4 channels of PWM DAC, 4 channels of 6-bit ADC, and a built-in sync-processor. It also includes two IIC Slave B ports, supporting VESA DDC/CI for both D-sub and DVI interfaces, and a Boot-Code-Free ISP (In System Programming). Confidential ViewSonic Corporation D o Not Copy V P730/b...
5. Adjusting Procedure Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 22
75 Hz, 49.7 KHz 1024 x 768 50 Hz, 39.6 KHz 1024 x 768 60 Hz, 48.4 KHz 1024 x 768 70 Hz, 56.5 KHz 1024 x 768 72 Hz, 58.1 KHz Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 23
Test Signal: 1280 x 1024 @ 60.0kHz Test Pattern: R, G, B, Color Intensities Pattern and 16 Gray Scale Pattern - Check and see if each color is normal and distinguishable. Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 24
After final QC step, we have to erase all saved changes again and restore the factory defaults. You should do “All Mode Reset” again. 5-1.5.13 Power off Monitor Turn off the monitor by pressing “Power” button. Confidential ViewSonic Corporation D o Not Copy V P730/b...
5-2. Firmware Upgrade Procedure 5-2.1 Equipment Needed - VP730 Monitor - Fixture for Firmware Upgrade - Power Adapter (P/N: 47.58201.001) *1 for Fixture - VGA Cable (P/N: 42.59901.003) *1(Pin 4, 11 should be connected to GND) - PC (Personal Computer) - LPT Cable (P/N: 42.59906.001) *1...
Page 26
C. Make sure the monitor was working under power saving mode and keep it at “Power Saving state” during DDC process. EDID-Kit Cable PC printer D-Sub of port 25pin Monitor connector 15pin VGA Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 27
2. Programming procedure A. Normally, you received a EDID zip file of new model. You need to unzipped it. B. There will need the following files for DDC program: (VP730 is an example) 1. DPS.EXE 2. VP730.BAT 3. VP730.DDC 4. VP730.CFG 5.
Page 28
Press 3 “DDC Writer/Check Data”: The Kit will start to program new data of EDID into monitor, all DDC data will display on the screen after programming. Please refer to Fig-DDC3 below, the DDC process is finished. Fig-DDC3 Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 29
Please refer to the Viewsonic EDID data format that was printing on ID label. PPPYYWWxxxxx PPP = Viewsonic Regional Product ID Code, EX. VE500 is “910”, VE700 is “A10” and VG900 is “A1C ”. YY= 2 digits of Manufacturing year. (range 1996-2015).
5.4 . ISP procedure Connection of ¢×S¢Þ Kit¡G Using ISP cable connect PC Print port Using VGA cable connect monitor (destination). Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 31
5. Click “Load MCU file” and then find the updated firmware code. 6. Click “Create Security File” going to next window MCU File Type Create Security File 7. Select Command No=4 Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 32
9. Click “OK” to start ISP function and update the firmware into Monitor. 2.Input Value 1.Command No 3. OK 10. Firmware update is finished when the display backed to the window below. Confidential ViewSonic Corporation D o Not Copy V P730/b...
7. Recommended Spare Parts List RECOMMENDED SPARE PARTS LIST (VP730-1) ViewSonic Model Number: VS10726-1W Rev: 1a Serial No. Prefix: PQB Description Item ECR/ECN ViewSonic P/N Ref. P/N Location Universal number# Q'ty Accessories: VGA CABLE A-VC-0101-0271 QCODS1584D8D--- SIGNAL CABLE POWER CORD...
Page 39
RECOMMENDED SPARE PARTS LIST (VP730b-1) ViewSonic Model Number: VS10726-1W Rev: 1a Serial No. Prefix: PQ9 Description Item ECR/ECN ViewSonic P/N Ref. P/N Location Universal number# Q'ty Accessories: VGA CABLE A-VC-0101-0271 QCODS1584D8D--- SIGNAL CABLE POWER CORD A-PC-0106-0180 QACC-1126D8D--- AC POWER CORD...
Page 40
BOM LIST (VP730-1) ViewSonic Model Number: VS10726-1W Rev: 1a Serial No. Prefix: PQB Item ViewSonic P/N Ref.P/N Description Location Universal number# Q'ty HW-00004129 GSTN-2956T8K--- STAND BASE (VP730) STAND BASE (VP730) #N/A XBPSN40P10JS0-- SCREW FOR HINGE STAND SCREW FOR HINGE STAND...
Page 43
BOM LIST (VP730b-1) ViewSonic Model Number: VS10726-1W Rev: 1a Serial No. Prefix: PQ9 Item ViewSonic P/N Ref.P/N Description Location Universal number# Q'ty HW-00004119 GSTN-2956T8K--B STAND BASE (VP730B) STAND BASE (VP730B) #N/A XBPSN40P10JS0-- SCREW FOR HINGE STAND SCREW FOR HINGE STAND...
8.Exploded Diagram And Spare Parts List ViewSonic Corporation Model Title Date Rev: Confidential - Do Not Copy ViewSonic Corporation VP730/b...
Page 47
EXPLODED PARTS LIST (VP730-1) ViewSonic Model Number: VS10726-1W Rev: 1a Serial No. Prefix: PQB Item ViewSonic P/N Ref. P/N Description Q'ty C-00004127 GCABA2368T8F--- CAB-A #N/A JKNBP2392T8F--- KNOB PL-00004124 HDECP2012T8F--- LENS B-00004103 DPWBN5722T8---- KEY BOARD PL-00004125 HBDGE1393T8---- LOGO PLATE E-00004115 VVLM170EG01V8-- 17” AUO PANEL...
Page 48
EXPLODED PARTS LIST (VP730b-1) ViewSonic Model Number: VS10726-1W Rev: 1a Serial No. Prefix: PQB Item ViewSonic P/N Ref. P/N Description Q'ty C-00004106 GCABA2368T8F--B CAB-A PL-00004123 JKNBP2392T8F--B KNOB PL-00004124 HDECP2012T8F--- LENS B-00004103 DPWBN5722T8---- KEY BOARD PL-00004125 HBDGE1393T8---- LOGO PLATE E-00004115 VVLM170EG01V8-- 17” AUO PANEL...
Page 49
Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 50
1.4 Place the monitor into the carton and then put all the accessories into the carton. At last, The carton and seal it with tape. (Figure 4) Figure 3 Figure 4 Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 51
Disassembly Lie down the monitor on flat table Remove Back cover and Stand by 4 screw Remove CAB-B: Take out 4 screw Take off D-sub 6 screws Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 52
Remove the power board by 3 screws Remove the Inverter board by 2 screws Remove the I/F board by 2 screws Confidential ViewSonic Corporation D o Not Copy V P730/b...
Key board Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 64
Confidential ViewSonic Corporation D o Not Copy V P730/b...
Page 65
Add.: Fax: Tel: E-mail: After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile 1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes (marc.maupin@viewsonic.com) Confidential - Do Not Copy...