Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes.
(13) Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be supplied by power complied with requirements of Limited ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 5
Do not touch and that may cause “Mura” the surface of the polarizer. Take out the monitor with cushions Taking out the monitor by grasping the LCD panel. That may cause “Mura” ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 6
Place the monitor on a clean and soft foam pad. Placing the monitor on foreign objects. That could scratch the surface of the panel or cause “Mura” The panel is placed facedown on the lap. That may cause “Mura” ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
No any sympathetic or abnormal noise allowed under Volume OSD ≤ 70% 5. Electrical Requirements Horizontal Frequency 24 – 82 kHz Vertical Refresh Rate 50 – 85 Hz. Maximum Pixel Clock 135 MHz Sync Polarity Independent of sync polarity. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 8
Average ¡Ø 4ms (Over Drive by scalar) *GTG response time was defined as average value of Tr and Tf for gray to gray signal change. Mercury 3 mg per lamp Panel Defects Please see Panel Quality Specifications. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 9
@ 70 Hz, 56.5 KHz 1024 x 768 @ 72 Hz, 58.1 KHz 1024 x 768 @ 75 Hz, 60.2 KHz For Composite and SOG signal, ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 10
*3. The image quality of 85Hz mode might be worse than 75Hz. 6. Mechanical Dimension (Desktop) Width 376 mm (14.8 inch) Height (Height adjust to the bottom) 363mm (18.2 inch) Depth 229mm (9 inch) Monitor Weight 5.4 Kg (11.9 lbs) ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 11
Height Adjust 0 ~ ≥ 100 mm Pivot CW 90º Package Specifications The “Top Level Assembly” shall meet the ViewSonic Corporation ViewSonic Packaging Spec Packaging Spec, VSCPACSPEC003 ViewSonic Pallet Spec Refer to ViewSonic Pallet Load Specification REV.1.I The ink shall not rub off after a suitable drying time.
Also toggles between two controls on saves adjustments. some screens. Also a shortcut to toggle analog and digital connection. Power light Green = ON Orange = Power Saving Standby Power On/Off ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 13
• If necessary, make small adjustments using H. POSITION and V. POSITION until the screen image is completely visible. (The black border around the edge of the screen should barely touch the illuminated “active area” of the LCD display.) ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Color Adjust provides several color adjustment modes, including preset color temperatures and a User Color mode which allows independent adjustment of red (R), green (G), and blue (B). The factory setting for this product is 6500K (6500 Kelvin). ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 15
Preset Timing Mode, colors return to the 6500K factory preset. Information displays the timing mode (video signal input) coming from the graphics card in the computer, the LCD model number, the serial number, and the ViewSonic website URL. See your graphics card’s user guide for ®...
Page 16
“15 second” setting, if a control is not pushed within 15 seconds, the display screen disappears. OSD Background allows the user to turn the OSD background On or Off. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 17
Preset Timing Mode listed in the Specifications of this manual. Exception: This control does not affect changes made with the User Color control, Language Select or Power Lock setting. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 18
[1] + [▲] OSD Lock No signal + [▼] + [▲] Burning mode [▲] + [2] + [ ] Factory Mode Remark : All the short cuts function are only available while OSD off ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Every window can place anywhere on the screen. Rotary 90,180,270 degree Independent row shadowing/bordering. Programmable blinking effects for each character OSD-made internal pattern generator for factory mode Support 12x18~5x18 proportional font ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 20
The low-pass filter in front of H/V scale-down plays a role of anti-aliasing filter. Moreover, the filter prior to vertical scale-down can be config as high-pass filter to serve as vertical peaking filter. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 21
The EM6A9320 provides programmable Read or Write burst lengths of 2, 4, 8. An auto precharge function may be enabled to provide a self-timed row precharge that is initiated at the end of the burst sequence. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 22
There are two signal to control the inverter which come from system. Logic “high” level which send to I901 is turn on the inverter. BRI signal control brightness by DC level which was integral from PWM signal. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 23
Ptot Total Power Dissipation (Tcase = 60°C) 6 W Tamb Ambient Operating Temperature 0 to 70 °C Tstg, Tj Storage and Junction Temperature -40 to 150 °C V6 Volume CTRL DC voltage 7 V 0 4 8 12 Area(cm2) ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
800 x 600 @ 60Hz, 37.9kHz 15. 800 x 600 @ 72Hz, 48.1kHz 800 x 600 @ 72Hz, 48.1kHz 16. 800 x 600 @ 75Hz, 46.9kHz 800 x 600 @ 75Hz, 46.9kHz ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 25
Figure 7, 8 Dark Screen pixels should be compliant with the spec. White Balance White & Black The screen must have the Figure 9 Pattern pure white and black pattern, no other color. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 26
Fine Line Morie Pattern (Figure1) Gray Scale Pattern (Figure2) Horizontal & Vertical Thickness Pattern (Figure 3) R. Color Pattern (Figure 4) G. Color Pattern (Figure5) B. Color Pattern (Figure 6) ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 27
Please select and enter “Auto Image Adjust” function on Main Menu to see if it is workable. The “Auto Image Adjust” function is aimed to offer a better screen quality by built-in ASIC. For optimum screen quality, the user has to adjust each function manually. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 28
- If not, please return the unit to repair area. 1.5.9 Screen Uniformity and Flicker Test Signal: 1280*1024@60Hz Test Pattern: Full White Pattern - Check and see if it is in normal condition. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 29
After final QC step, we have to erase all saved changes again and restore the factory defaults. You should do “All Mode Reset” again. 1.5.15 Power Off Monitor Turn off the monitor by pressing “Power” button. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 30
2.2.1 Connect P2 of Fixture with printer port of PC by LPT Cable. 2.2.2 Connect P1 of Fixture with Monitor by VGA Cable. 2.2.3 Connect Power Cord to Monitor. 2.2.4 Connect PC to the additional monitor. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 31
I. ISP Download program procedure Hardware Connect status: Down load isp program Step 1: Execute ISP.exe ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 32
Then press the Creat Security File Button to enter step 3. Step 3: Creat Security File Enter the three string into the blank like fig 2. Then press OK Button. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 33
Press the Load MCU File button to select the file will be download. (*.hex) Step 5: Run Pressing the Run Button to start download program. Press OK button to Enter ISP mode. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 34
If the test result shows “passed,” it means the connection is well. If not (failed), it means the connection has problems. Then you need to check the setup procedure or reboot the PC, or simply use another PC to do the firmware upgrade. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 36
4.(when key in DVI DDC information, use VGA transform to DVI port ) 5.Connect Power Cord to VP720 Monitor. 3.3 DDC Key In Procedure 1.Run DDC.exe 2.Choose model number and conform the Time then Press “ENTER” key. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 37
3.When appear the PIC “ choose DDC Card”, Press ALT+2 .Enter DDC 2B test interface. Choose DDC Card 4.Press F8 to choose corresponding model.DAT(VP720-A.DAT press“ENTER” key) VP720_A means the DDC under analog mode. VP720-D means the DDC under digital mode. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 38
5.Press F9 enter the download interface 6.Key in the serial number or use the barcode reader to scan the barcode of the monitor, and press “ENTER” key. ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 39
7.The successful picture is as follows. ”Compare EDID :OK! Press any key to continue”. 8.Let VP720 active, then see the information in OSD, it shows ”Serial NO : PXX054700001” ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 40
3.4 check method Use ViewSonic EDID Editor Connect the VP720 to PC with VGA Cable. Excute the EDID Editor, then Press Ctrl+F5. If the DDC is correct, you can see the information as follow: ViewSonic Corporation Confidential – Do Not Copy...
Page 41
1. Disassembly of Stand unit from Monitor 1.1 Unscrew four screws that secure Stand Unit. Stand 2. Disassembly of Front Cover,Rear Cover and Speaker. 2.1 Detach Front Cover from monitor. Front Cover ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 42
2.2 Unscrew 6 screws to remove Rear Cover. Rear Cover 2.3 Disconnect the wires to remove Speaker module. Speaker ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 43
3. Disassembly of Power Board,Main Board,Keypad Board and Panel Unit 3.1 Unscrew 6 screws to remove Shielding Plate. Hinge Shielding Plate 3.2. Unscrew 4 screws and disconnect the wires to remove Power Board. Power Board ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 44
3.3. Unscrew 2 screws and disconnect the wires to remove Main Board. Main Board 3.4. Lay Panel Unit facedown and unscrew 4 screws on its right and left sides to remove Panel Unit and Keypad Board. Panel Unit Panel Bracket Keypad Board ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
1.4 Place the monitor into the carton and then put all the accessories into the carton. At last, close the Power Cord carton and seal it with tape. (Figure 5) DVI Cable VGA Cable Audio Cable Figure 4 Figure 5 User’s Guide ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
OK ? CHECK I101 CHECK I101 1.8V 1.8V SUROUND CAP UROUND CAP BEAD OK ? OK ? CHECK I105, CHECK I105 2.5V 2.5V SUROUND CAP UROUND CAP BEAD OK ? OK ? ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 47
PIN41 3.3V? D102,L107 CHECK CHECK 24MHZ PIN15,16 X102,C232 C233 OK ? CHECK CHECK TRACE PIN15,PIN16 OK ? CLOCK OK ? CHECK CHECK I106 EVERY TWO KEYPAD PIN SHORT ? P107 OK ? ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
Page 51
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
Page 52
BOM LIST (VP720-1) ViewSonic Model Number: VS10927-1W Rev: 1a Serial No. Prefix: PXV Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty #N/A 2341150996P CAP,CHIP 125'C CS 0603/COG/50V 5.0p J T C101 1.000" #N/A 2341150996P CAP,CHIP 125'C CS 0603/COG/50V 5.0p J T C102 1.000"...
Page 53
Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty E-C-0404-3815 2346410496P CAP,CHIP 85'C CS 0603/Y5V/50V 0.1u Z T C207 1.000" E-C-0404-3815 2346410496P CAP,CHIP 85'C CS 0603/Y5V/50V 0.1u Z T C208 1.000" E-C-0404-3815 2346410496P CAP,CHIP 85'C CS 0603/Y5V/50V 0.1u Z T C209 1.000"...
I601 TDA7496L DDC-SD A I106 ONBACKLI AUDIO AMP VOLUME CONTROL MTV512GMG64 DDC- SCL (OPTION) SPEAKE STANDBY I107 24LC16 EEPROM 3.3V P603 AUDIO IN KEY- PAD LED ViewSonic Corporation Model Title Date Rev: ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
11. PCB Layout Diagrams 11.1. MAIN PCB TOP VIEW ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 88
11.2. MAIN PCB BOTTOM VIEW ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 89
11.3. CON PCB TOP VIEW 11.4. CON PCB BOTTOM VIEW ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 90
11.5. POWER PCB TOP VIEW ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 91
11.6 POWER PCB BOTTOM VIEW ViewSonic Corporation Confidential – Do Not Copy VP720-1_VP720b-1...
Page 92
Company: Add.: Fax: Tel: E-mail: After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile 1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes (marc.maupin@viewsonic.com) ViewSonic Corporation Confidential – Do Not Copy...