Page 1
SYSTEM AIR CONDITIONER Basic: JH035EAV1 JH026EAV1 Model : JH052EAV Series JH035EAV Series JH026EAV Series Model Code : JH052EAV1 UH052EAV1 JH035EAV1 UH035EAV1 JH026EAV1 UH026EAV1 AIR CONDITIONER CONTENTS 1. MPI Zone (Air cleaning solution) 2. Special Filter 3. Flexible Pipe Installation 4. Elegance Design...
In case the product will not be in use for a long time, the battery of remote control should be kept separately. – Leakage of inside fluid can cause break down of remote control. Samsung Electronics Eiffiel_29331A_10.22.08.indd 1 2008-10-22 17:03:04...
Floor standing type Air Conditioner, Powerful on floor heating & cooling. MPI Zone (Air cleaning solution) Samsung’s Micro Plasma Ion Zone is a technology that generates activated hydrogen and oxygen ions, which exterminates viruses and allergy-causing microbes in the air by neutralizing them and turning into water.
Page 13
Disassembly and Reassembly Parts Procedure Remark Electrical Parts 1) Open the cover of Control Box ). 2) Pull the PBA out along the slide guide. Cut the Cable tie. Pull all wires out from the PBA. Samsung Electronics Eiffiel_29331A_10.22.08.indd 10 2008-10-22 17:03:15...
Page 14
6) Release 2 Hold Wires and pull all wires out from it . Blowing 1) Pull the Bracket Pipe( )out. & Evap Part 2) Release 2 screws and pull Top Discharge Kit( ) out. Samsung Electronics Eiffiel_29331A_10.22.08.indd 11 2008-10-22 17:03:19...
Page 15
This part is right side of the Bottom Discharge Kit( ). 5) Pull Bottom Discharge Kit( ) Out from the bottom of it. 6) Release 3 screws and pull the Evap out from top to bottom direction. Samsung Electronics Eiffiel_29331A_10.22.08.indd 12 2008-10-22 17:03:22...
Page 16
3) Release 6 screw on the Body Back( ). Pull the Cap MPI( ), Bracket Wire( ) and Bracket Motor( ) out. 4) Pull the MPI Kit( ) and Motor( ) out from the Body Back( ). Samsung Electronics Eiffiel_29331A_10.22.08.indd 13 2008-10-22 17:03:26...
Cabinet Front. (Use +Screw Driver.) 3) Separate the Cabinet Front as shown on the right picture. 4) Undo fixing screw to remove Plate Control Out on the Cabinet Side RH. (Use +Screw Driver.) Samsung Electronics Eiffiel_29331A_10.22.08.indd 14 2008-10-22 17:03:27...
Page 18
Cabinet Side RH. (Use +Screw Driver.) 6) Undo 3 fixing screws to assemble Bracket Valve on the Cabinet Side RH. (Use +Screw Driver.) 7) Undo 2 fixing screws on the Cabinet Side LF. (Use +Screw Driver.) Samsung Electronics Eiffiel_29331A_10.22.08.indd 15 2008-10-22 17:03:27...
Page 19
2) Separate several Connectors from the PCB of the Ass’y Control Out. 3) Separate 2 Connect Wires from the Reactor. 4) Undo a fixing screw to assemble the Ass’y Control Out on the Partition. (Use +Screw Driver.) Samsung Electronics Eiffiel_29331A_10.22.08.indd 16 2008-10-22 17:03:28...
Page 20
When separating Compressor, Heat Exchanger and pipes please ensure that Compressor is completely free from any remaining refrigerant then separate all pipes with welding torch. Ass'y Valve 4 Way 1) Separate 3 welded parts. Samsung Electronics 3-10 Eiffiel_29331A_10.22.08.indd 17 2008-10-22 17:03:29...
Page 21
2) Separate the Terminal Cover and then Connect Wires from the Compressor. 3) Separate the Felt Comp Sound. 4) Undo 3 bolts on the flow of the Compressor as shown in the right-hand picture. (Use Monkey Spanner.) 3-11 Samsung Electronics Eiffiel_29331A_10.22.08.indd 18 2008-10-22 17:03:30...
Page 22
Operating Instructions and Installation UH052EAV1 Parts Procedure Remark Common Work 1) Loosen 1 fixing screw of the Cover- Control and detach the Cover Control. 2) Loosen fixing screws and detach the Cabinet-Upper. Samsung Electronics 3-12 Eiffiel_29331A_10.22.08.indd 19 2008-10-22 17:03:31...
Page 23
Procedure Remark 3) Loosen 1 screw fixed to assemble Control Box with Cabinet-Side RH. 4) Loosen 6 fixing screws and detach the Cabinet-Side RH. 5) Loosen 2 screws fixed on the Guide Condenser. 3-13 Samsung Electronics Eiffiel_29331A_10.22.08.indd 20 2008-10-22 17:03:32...
Page 24
Operating Instructions and Installation Parts Procedure Remark 6) Loosen fixing screws of the Cabinet Front. Samsung Electronics 3-14 Eiffiel_29331A_10.22.08.indd 21 2008-10-22 17:03:33...
Page 25
2) Detach the Fan Propeller. 3) Loosen 4 fixing screws to detach the Motor. 4) Disconnect the wire between ASS’Y Control Out and Motor. 5) Loosen 2 fixing bolts and detach the Bracket Motor. 3-15 Samsung Electronics Eiffiel_29331A_10.22.08.indd 22 2008-10-22 17:03:34...
Page 26
3) Disassemble the pipes in both inlet and outlet with welding torch. 4) Detach the Heat Exchanger. 5) Loosen 4 bolts fixed to assemble Valve Service with Bracket Valve like the picture on the right side. Samsung Electronics 3-16 Eiffiel_29331A_10.22.08.indd 23 2008-10-22 17:03:35...
Page 27
1) Loosen the fixing nut and detach the Compressor Lead Wire. 2) Disassemble the Felt Compressor Sound. 3) Loosen the 3 bolts at the bottom of Compressor like the picture on the right side. 3-17 Samsung Electronics Eiffiel_29331A_10.22.08.indd 24 2008-10-22 17:03:36...
repeatedly. Push the button to set the display panel to Every time you push the button, the display panel reads .. repeatedly. Samsung Electronics Eiffiel_29331A_10.22.08.indd 1 2008-10-22 17:03:43...
Page 29
If all lamps of indoor unit are flickering, Plug out, plug in power plug again and press ON/OFF key to retry. If the unit is not working properly or all lamps are continuously flickering after setting the option code, see if the correct option code is set up for its model. Samsung Electronics Eiffiel_29331A_10.22.08.indd 2 2008-10-22 17:03:50...
Main-Inverter Micom(After 1 minute of (Display is unrelated with Main-Inverter detection) operation) On Flickering X Off If you turn off the air conditioner when the LED is flickering, the LED is also turned off. Samsung Electronics Eiffiel_29331A_10.22.08.indd 4 2008-10-22 17:03:53...
Page 32
EEPROM error EEPROM option error MPI no feedback Error On Flickering X Off If you turn off the air conditioner when the LED is flickering, the LED is also turned off. Samsung Electronics Eiffiel_29331A_10.22.08.indd 5 2008-10-22 17:03:54...
1 min.time out Comm. Fan error OTP error Comp rotation error Operation condition secession (main/main) DC-Link voltage sensor error I_Trip error/PFC over current Gas Leak error AC line Zero Cross Signal out Capacity miss match Samsung Electronics Eiffiel_29331A_10.22.08.indd 6 2008-10-22 17:03:56...
Check the resistance values of sensor Outdoor unit Excessive temperature emission Not an error (discharge temp. control) protection control error Outdoor sensor Power cable connection error Check the status of power connection Operation-off error Samsung Electronics Eiffiel_29331A_10.22.08.indd 7 2008-10-22 17:03:57...
Page 35
Check the fuse of indoor/outdoor unit Check refrigerant is filled Self-diagnosis Gas leakage error Operation-off Check the indoor EVA sensor error Outdoor unit Inconsistent volume Check the indoor unit’s option code Operation-off protection control error Samsung Electronics Eiffiel_29331A_10.22.08.indd 8 2008-10-22 17:03:58...
Page 36
COM2 terminal of the indoor unit error Wired remote Wired remote controller COM2 Check the Dip switch for Com1 and Com2 Normal operation controller control setting option error is set to Com2 error Samsung Electronics Eiffiel_29331A_10.22.08.indd 9 2008-10-22 17:03:59...
6.900 At that time, does the resistance value deviate from the 8.300 temp. table beside? 10.00 12.10 Indoor temp. sensor 14.70 self-defect (replacement) 18.00 Resume operation after replacing PCB 22.00 28.30 33.90 42.30 4-10 Samsung Electronics Eiffiel_29331A_10.22.08.indd 10 2008-10-22 17:03:59...
At that time, does the 8.300 resistance value deviate from the temperature 10.00 table beside? 12.10 Indoor Heat Exchange temp. 14.70 sensor 18.00 self-defect (replacement) Resume operation after replacing PCB 22.00 28.30 33.90 42.30 Samsung Electronics 4-11 Eiffiel_29331A_10.22.08.indd 11 2008-10-22 17:04:00...
PCB? Resume operation after connecting to the connector PCB Is there any clogging (binding) of foreign substances in the MotorFan? Resume operation after removing the foreign substances. Resume operation after replacing PCB 4-12 Samsung Electronics Eiffiel_29331A_10.22.08.indd 12 2008-10-22 17:04:00...
After reconnecting the communication line that links outdoor and indoor units, remove communication connector in the indoor PCB. If communication does not work during operation, replace PCB of the indoor unit. Good defect +0.7V -0.7V Samsung Electronics 4-13 Eiffiel_29331A_10.22.08.indd 13 2008-10-22 17:04:01...
Bridge 10de replacement (DB300) DC265V~DC357V? Is reactor 1 and 2 (reactor connection wire) properly connected Connect the connection wire of the reactor to the reactor? Power ok? Replace outdoor unit PCB for Outdoor MICOM defect. Finish Samsung Electronics 4-15 Eiffiel_29331A_10.22.08.indd 15 2008-10-22 17:04:02...
1) Is compressor operating properly? 2) Is there a connection between input power and power? 2. Inspection order Is EMI PCB and Turn off the power then reconnect Inverter PCB connected properly? Replace PCB 4-16 Samsung Electronics Eiffiel_29331A_10.22.08.indd 16 2008-10-22 17:04:02...
Page 44
PCB Measure the amount of Ion with tester. MPI Kit Tester: ITC201A 100,000. HE NUMBER OF MEASURED ON IS MORE THAN Normal operation Change the MPI Kit (it’s out of the work) Samsung Electronics 4-17 Eiffiel_29331A_10.22.08.indd 17 2008-10-22 17:04:03...
Are the values for R418 Resistance replacement current sensing resistance within 19mΩ-21mΩ? Is resistance value of the different compressor phases Compressor replacement (UV, V W, WU) less than 2Ω? Continue (continued on the back) 4-18 Samsung Electronics Eiffiel_29331A_10.22.08.indd 18 2008-10-22 17:04:04...
Page 46
Is the connection Turn off the power then cable between the compressor and PCB correct the sensor location or replace it properly connected? Replace PCB Samsung Electronics 4-19 Eiffiel_29331A_10.22.08.indd 19 2008-10-22 17:04:04...
Is the resistance Replace the Compressor between the Compressor body and chassis Maga Ω? Is the Compressor connection line properly connected to the Check the connection line Compressor? Replace the outdoor unit’s PCB 4-20 Samsung Electronics Eiffiel_29331A_10.22.08.indd 20 2008-10-22 17:04:05...
Do they indicate DC1V~DC4V? Is there a Replace temperature sensor after turning short circuit or defective contact in off the power the sensor wires? Replace PCB after turning off the power Samsung Electronics 4-21 Eiffiel_29331A_10.22.08.indd 21 2008-10-22 17:04:05...
Do they indicate DC1V~DC4V? Is there a Replace temperature sensor after turning short circuit or defective contact in off the power the sensor wires? Replace PCB after turning off the power 4-22 Samsung Electronics Eiffiel_29331A_10.22.08.indd 22 2008-10-22 17:04:06...
Do they indicate DC1V~DC4V? Is there a Replace temperature sensor after turning short circuit or defective contact in off the power the sensor wires? Replace PCB after turning off the power Samsung Electronics 4-23 Eiffiel_29331A_10.22.08.indd 23 2008-10-22 17:04:07...
Replace PCB of the outdoor unit block F1–F2, less than DC5V? after turning off. When measuring F1–F2, the outdoor terminal block, if the voltage varies (communicates) below DC5V, the connection status of the connection line is normal. 4-24 Samsung Electronics Eiffiel_29331A_10.22.08.indd 24 2008-10-22 17:04:07...
No.1 and No. 3 pin of the the voltage of the no.13 pin of the outdoor unit CN01 between 1V~5V? the IC01 (MICOM)? Replace the main PCB of the Defective MICOM outdoor unit Continue (continued on the back) Samsung Electronics 4-25 Eiffiel_29331A_10.22.08.indd 25 2008-10-22 17:04:08...
Page 53
Is there any change in the voltage of the Replace the main PCB of the no.13 pin of the IC01 outdoor unit (MICOM)? Replace the main PCB of the Replace BLDC fan motor outdoor unit 4-26 Samsung Electronics Eiffiel_29331A_10.22.08.indd 26 2008-10-22 17:04:09...
Is the outdoor unit installed correctly? Reinstall after removing obstacle Is indoor unit installed correctly? Reinstall after removing obstacle Is the compressor operating normally? Replace the compressor Is the service valve open completely? Open valves Replace PCB Samsung Electronics 4-27 Eiffiel_29331A_10.22.08.indd 27 2008-10-22 17:04:09...
V W, W U) less than 2Ω? Is the service valve open completely? Open valves Is the indoor EVA sensor connected properly? Reconnect the sensor connector ace th Is refrigerant filled? Replace the outdoor unit’s PCB 4-28 Samsung Electronics Eiffiel_29331A_10.22.08.indd 28 2008-10-22 17:04:11...
5. AC zero Crossing signal out error Check the connection between input power and the power is okay then replace the PCB 6. Inconsistent volume Check the option code of the indoor unit. Samsung Electronics 4-29 Eiffiel_29331A_10.22.08.indd 29 2008-10-22 17:04:11...
#2~#5. Control SIGNAL #2.Communication Signal F2 #2~#5.Communication Signal #1. Communication Signal F1 #2. Communication Signal F2 CN20-MICOM Download2 CN10-MICOM Download1 > For Developer,Not for field >For Developer, Not for field > 7pin Downloader >10pin Downloader Samsung Electronics Eiffiel_29331A_10.22.08.indd 38 2008-10-22 17:04:43...
Page 69
PCB Diagram and Parts List Display CN952(4PIN/WHT) : Display CN951(10PIN/WHT) : Display #1~4 : Receive signals from the Main #1~7 : 7-SEGMENT signal #8~10 : Receive KEY operation signals from the Main Samsung Electronics Eiffiel_29331A_10.22.08.indd 42 2008-10-22 17:04:58...
Page 70
#5 : DETECT FAN RPM #6 : FAN FG CN30(6P/WHT)-EEV CN20(4P/WHT)-DISPLAY CN21(10P/WHT)-DISPLAY #1~4 : RECEIVE SIGNAL FROM THE MAIN #1~7 : 7-SEGMENT SIGNAL #8~10 : RECEIVE KEY OPERATION SIGNALS FROM THE MAIN CN01(2PIN/BLU)-12V REACTOR1,2(TAB)-REACTOR Samsung Electronics Eiffiel_29331A_10.21.08.indd 45 2008-10-21 15:44:13...
Page 71
PCB Diagram and Parts List EMI L(TAB)-POWER N(TAB)-POWER AC(L) AC(N) Samsung Electronics Eiffiel_29331A_10.21.08.indd 46 2008-10-21 15:44:13...
BLDC Fan Motor Part Display. Part Fan motor BLDC Part Ventilator (option) 4way. Part Communication. Part Comp. Part Outdoor Unit Intdoor Unit This Document can not be used without Samsung’s authorization. Samsung Electronics Eiffiel_29331A_10.21.08.indd 4-68-4-69 Eiffiel_29331A_10.21.08.indd 4-68-4-69 2008-10-21 15:53:49 2008-10-21 15:53:49...
8-1-1 MAIN PCB BLDC CONTROL Part MPI Part SENSOR Part E485 COMMUNICATION Part DOWNLOAD Part DAMPER Part DISPLAY Part ADDRESS CONTROL Part This Document can not be used without Samsung’s authorization. Samsung Electronics Eiffiel_29331A_10.21.08.indd 4-70-4-71 Eiffiel_29331A_10.21.08.indd 4-70-4-71 2008-10-21 16:02:51 2008-10-21 16:02:51...
Operating Instructions and Installation Schematic Diagram 8-1-2 Damper This Document can not be used without Samsung’s authorization. Samsung Electronics Eiffiel_29331A_10.22.08.indd 72 2008-10-22 17:05:11...
Operating Instructions and Installation Schematic Diagram 8-1-3 PCB Display This Document can not be used without Samsung’s authorization. Samsung Electronics Eiffiel_29331A_10.22.08.indd 73 2008-10-22 17:05:12...
8-2 Outdoor Unit 8-2-1 UH026/035EAV1 ■ INVERTER Fan Motor Drive Unit Inverter SMPS Micom Communication This Document can not be used without Samsung’s authorization. Samsung Electronics Eiffiel_29331A_10.21.08.indd 4-74-4-75 Eiffiel_29331A_10.21.08.indd 4-74-4-75 2008-10-21 16:08:30 2008-10-21 16:08:30...
Page 102
Schematic Diagram Schematic Diagram ■ INVERTER (cont.) Temp. Sensor Part & EEV part 485 Communication Circuit Part This Document can not be used without Samsung’s authorization. Samsung Electronics Eiffiel_29331A_10.21.08.indd 4-76-4-77 Eiffiel_29331A_10.21.08.indd 4-76-4-77 2008-10-21 16:08:40 2008-10-21 16:08:40...
Using a hex wrench, turn the needle valve countercloc�wise to open the valve. It is used for vacuuming, gas drain, refrigerant injection, refrigerant purge, and indoor-outdoor units connection. Accumulator It prevents liquid refrigerant from flowing into the compressor. (If liquid refrigerant enters the compressor, it becomes overloaded) Samsung Electronics Eiffiel_29331A_10.22.08.indd 2 2008-10-22 17:06:14...
Page 108
Using a hex wrench, turn the needle valve countercloc�wise to open the valve. It is used for vacuuming, gas drain, refrigerant injection, refrigerant purge, and indoor-outdoor units connection. Accumulator It prevents liquid refrigerant from flowing into the compressor. (If liquid refrigerant enters the compressor, it becomes overloaded) Samsung Electronics Eiffiel_29331A_10.22.08.indd 3 2008-10-22 17:06:14...