Sharp MX-3500N Service Manual page 234

62-12
Purpose Data clear
Function (Purpose) Used to set Enable/Disable of auto format
in HDD trouble.
* Be sure to format the HDD in FAT32.
Section MFP (HDD)
Item Clear
Operation/Procedure
1) When the machine enters the simulation, the screen on the
right is displayed.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered values.
3) When [OK] button, [COLOR], or [BLACK] key is pressed, it is
highlighted and the current entered value is saved to EEPROM
and RAM.
<Descriptions of buttons, set range, and default values>
Item Content
A (0: YES, 0 Auto format Enable
1: NO)
1 Auto format Disable
SIMULATION NO.62 12
TEST
AUTO FORMAT SETTING HDD TROUBLE
A 0 (0:YES 1:NO)
A:
0
0 1
62-13
Purpose Data clear
Function (Purpose) Used to format the hard disk (operation
manual area only).
* Be sure to format the HDD in FAT32.
Section MFP (HDD)
Item Clear
Operation/Procedure
1) Press [EXECUTE] button.
[EXECUTE] button is highlighted and [YES] and [NO] buttons
become active.
2) Press [YES] button.
3) The hard disk (operation manual area only) is formatted. [YES]
button is highlighted.
* When [NO] button or [EXECUTE] button is pressed, [EXE-
CUTE] button returns to the normal display, and [YES] and
[NO] buttons gray out.
* During formatting the hard disk (operation manual area
only), [EXECUTE] button is highlighted and "HDD FORMAT
(MANUAL AREA ONLY) EXECUTING..." is displayed.
* If formatting of the hard disk (operation manual area only) is
not completed normally, "HDD FORMAT (MANUAL AREA
ONLY) NG" is displayed.
* When formatting of the hard disk (operation manual area
only) is completed, [EXECUTE] button returns to the normal
display and [YES] and [NO] buttons gray out.
* When [CA] key or [SYSTEM SETTINGS] key is pressed to
exit the simulation, the machine is rebooted.
AUTO FORMAT SETTING HDD TROUBLE
63
63-1
Purpose
Set Default
Function (Purpose) Used to check the following values related
range value
0 to 1 1 (Disable)
Section
Item
0
Operation/Procedure
CLOSE
CLOSE
1)
OK
* When [CLOSE] button is pressed, the display shifts to the copy
* Copying can be performed also by pressing [COLOR]/[BLACK]
<Display item and description> (MX-3500N/4500N)
GAIN ODD
GAIN EVEN
OFFSET ODD
OFFSET EVEN
SMP AVE ODD
SMP AVE EVEN
TARGET VALUE
BLACK LEVEL
ERROR CODE
RSPF WHITE
LEVEL 1ST
MX3500N SIMULATION 7 – 126
SIMULATION NO.62 12
TEST
A 1 (0:YES 1:NO)
A:
1
0 1
Adjustment/Setup/Operation data output/
Check (Display/Print)
to shading for RGB and OC/RSPF/DSPF.
(3 x 2 = 6 kinds)
Scanner (Exposure)
Operation
Select a color button to be displayed.
The shading set value of the selected button is displayed.
* When [B](Blue), [G](Green), or [R](Red) button is selected,
the selected button is highlighted and the adjustment value
of the selected color is displayed.
* Only one color button can be selected, and the selected but-
ton is highlighted. In the initial state, [B] is selected.
* If there is a page over [↑], an active display is shown and the
page moves up. If there is no page upward, the display
grays out and the operation is invalid.
If there is a page under [↓], an active display is shown and
the page moves down. If there is no page downward, the
display grays out and the operation is invalid.
basic screen of simulation.
key.
Display item Description
Gain adjustment value
(ODD)
Gain adjustment value
(EVEN)
Offset value (ODD)
Offset value (EVEN)
Reference plat sampling
average value (ODD)
Reference plat sampling
average value (EVEN)
Target value
Black output level
Error code (0, 1 to 4)
First scan, RSPF white
reference level
0
CLOSE
CLOSE
OK
Remark
0: No error
1: STAGE1. Over the
loop number
2: STAGE2. The target
value is less than the
specified level.
3: STAGE3. The gain
set value is negative.
4: END is not
asserted.