Table of Contents
Advertisement
this mode, refer to your wide-screen TV's instruction
manual. During playback/recording on 4:3 TVs/LCD
monitor/viewfinder, the image is elongated vertically.
* Available only when the VIDEO/MEMORY Switch is set to
"VIDEO".
WIND CUT
[OFF]: Disengages the function.
ON
: Helps cut down on noise created by wind. The
"
" indicator appears. The quality of the sound will
change. This is normal.
The "s" functions which are set when the Power Switch
is set to "M" are also applied when the Power Switch is
set to "PLAY".
[ ] = Factory-preset
BEEP
OFF: Turns off sounds when performing any operations.
It also deactivates the shutter sound effect, however the
shutter sound is recorded onto the tape during Snapshot
for Video Recording (
BEEP: The beep sounds when the power is turned on or
off, and at the beginning and end of recording. It also
activates the shutter sound effect. (
[MELODY]: Instead of a beep, a melody sounds when
any operation is performed. It also activates the shutter
sound effect. (
pg. 18, 31)
REMOTE
OFF: Disables the remote control operations.
[ON]: Enables the remote control operations.
DEMO MODE
OFF: Automatic demonstration will not take place.
[ON]: Demonstrates certain functions such as Program
AE with special effects, etc., and can be used to confirm
how these functions operate. Demonstration starts in the
following cases:
When the Menu Screen is closed after "DEMO MODE" is
turned "ON".
With "DEMO MODE" set to "ON", if there is no operation for
about 3 minutes after the Power Switch is set to "A" or "M".
Performing any operation during the demonstration stops
the demonstration temporarily. If no operation is
performed for more than 3 minutes after that, the
demonstration will resume.
NOTES:
If a cassette is in the camcorder, the demonstration cannot
be turned on.
"DEMO MODE" remains "ON" even if the camcorder power
is turned off.
If "DEMO MODE" remains "ON", some functions will not be
available. After viewing demo, set to "OFF".
PRIORITY
[LCD]: The image is displayed on the LCD monitor when
the viewfinder is pulled out while the LCD monitor is
opened.
SYSTEM
pg. 31).
pg. 18, 31)
MENUS FOR DETAILED ADJUSTMENT
FINDER: The image is displayed in the viewfinder when
the viewfinder is pulled out while the LCD monitor is
opened.
CAM RESET
EXECUTE: Resets all settings to the factory-preset.
RETURN: Does not reset all settings to the factory-
preset.
CAMERA DISPLAY
The "n" (CAMERA DISPLAY) settings are effective even
when the Power Switch is set to "A". However, the menu
settings can be changed only when the Power Switch is set
to "M".
The "n" (CAMERA DISPLAY) settings are effective only
for shooting except "BRIGHT".
[ ] = Factory-preset
BRIGHT
pg. 9, "Brightness Adjustment Of The Display"
ON SCREEN
LCD: Keeps the camcorder's display (except the date,
time and time code) from appearing on the connected TV
screen.
[LCD/TV]: Makes the camcorder's display appear on
screen when the camcorder is connected to a TV.
DATE/TIME
OFF: The date/time does not appear.
[AUTO]: Displays the date/time for approx. 5 seconds
when the Power Switch is set from "OFF" to "A" or "M".
ON: The date/time is always displayed.
The date indication can also be turned on/off by pressing
the DISPLAY Button on the remote control. (
TIME CODE
[OFF]: Time code is not displayed.
ON: Time code is displayed on the camcorder and on the
connected TV. Frame numbers are not displayed during
recording. (
pg. 13)
CLOCK ADJ.
pg. 8, "Date/Time Settings"
[ ] = Factory-preset
QUALITY
[FINE] / STANDARD
The Picture Quality mode can be selected to best match
your needs. Two Picture Quality modes are available:
FINE (
) and STANDARD (
NOTE:
The number of storable images depends on the selected
picture quality as well as the composition of the subjects in
the images and the type of memory card being used.
(
pg. 18)
EN
pg. 17, 34)
DSC
) (in order of quality).
27
Advertisement
Table of Contents
