ActionTec DSL Gateway Quick Start Manual

1
Connect the DSL Gateway
Note: The pictures included in this Section are for the 4-port DSL Gateway.,If you have
a DSL Gateway with 1 Yellow Port,some of the pictures may not match your installation.
Step 1 Get your DSL Gateway from
your DSL Quick Start Kit and take it out
of the bag.
Step 2 Get the BLACK bag and remove
the Power Cord and black DSL Cable
from the bag.
Step 3 Plug the smaller end of the
Power Cord into the Black Port located
on the back of the DSL Gateway.
This port is circular and marked "Power" .
Step 4 Plug the larger end of the Power
Cord into a Power Outlet.
Step 5 Confirm that the Power light
on the DSL Gateway is GREEN. This
may take a few moments.
Step 6 Get the Yellow Cable from your
DSL Quick Start Kit.
Step 7 Connect one end of the Yellow
Cable into the Yellow Port on the back
of your DSL Gateway. You will hear a
"click" when the Yellow Cable has been
connected properly.
You can plug the Yellow Cable into any
open Yellow Port.
Step 8 Plug the loose end of the Yellow
Cable into the Ethernet Port located
on the back of your computer. You will
hear a "click" when the Yellow Cable has
been connected properly.
The Ethernet Port looks similar to a regular
Phone Jack but is slightly larger.
Step 9 Confirm that the Power and one
of the Ethernet Network lights on the
Cable/DSL Router are SOLID GREEN.
(This may take a few moments and the
Gateway light may flash.)
Step 10 Now get the black DSL Cable.
Step 10 Plug one end of the DSL Cable
into the GREEN Port, labeled "Line" , which
is located on the back of the DSL
Gateway.
Step 11 Plug the other end of the DSL
Cable into the Phone Jack closest to
your computer.
Step 12 Confirm that the Internet light
on the DSL Gateway is SOLID GREEN.
(This may take up to 30 seconds.)
Note: If the Internet light continues to blink, confirm that you have received
notification from your DSL Provider that your DSL service is ON. Otherwise,
contact your DSL Provider immediately.
2
Connect the Filters
These instructions will change based on your location.
If you are located in the United States, please go to the "U.S.
Customers ONLY" section.
If you are NOT located in the United States, please go to the
"Non-U.S. Customers ONLY" section.
U.S Customers ONLY
Phone Filters are connected to all of the Phone Jacks in your
home to allow you to talk on the phone and be online at the
same time. Every phone in your home with the same phone
number as your DSL line will need a Phone Filter.
Get the CLEAR Bag and take out the Phone Filters.
Note: The number and type of Phone Filters included in this kit may vary. It is
dependent on your Internet Service Provider.
Home Security Alarm Notice
If you have a monitored home security alarm,
please contact your Security System Provider to
schedule a visit to your home for installation of a
Phone Filter on the Alarm.
Step 1 Unplug all of the existing Phone Phone
Jack
Cords from their current Phone Jacks.
Phone
Cord
Note: DO NOT unplug the DSL Cable from the Phone Jack near your computer.
Step 2 Plug a Phone Filter into every
Phone Jack in your home.
Note: DO NOT plug a Phone Filter into the Jack on the wall near your computer.
Step 3 Plug the loose end of the existing
Phone Cord into a Phone Filter and
keep the other end connected to the
Phone (or fax machine, caller ID, or
answering machine) itself.
If you want to have a Phone next to your Computer:
Step 4 Find the Phone Cord that is
connected to the Telephone next to
your Computer. Unplug this Phone Cord
from the Phone Jack that it is currently
plugged into. Keep the other end
connected to the Telephone itself.
Note: DO NOT unplug the DSL Cable from the Phone Jack near your computer.
Please flip this Guide over now.
Stock# 0530-0405-000