Chrysler 2014 Town&Country Owner's Manual

Table of Contents

Quick Links

Download this manual

Town & Country

2 0 1 4

O W N E R ' S M A N U A L

Table of Contents

Chapters

Table of Contents

Summary of Contents for Chrysler 2014 Town&Country Chrysler

Page 1 Town & Country 2 0 1 4 O W N E R ’ S M A N U A L...
Page 2 With respect to any Vehicles Sold in Canada, the name Chrysler This manual illustrates and describes the operation of features Group LLC shall be deemed to be deleted and the name Chrysler and equipment that are either standard or optional on this Canada Inc.
Page 3: Table Of Contents
TABLE OF CONTENTS SECTION PAGE INTRODUCTION ............. 3 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE .
Page 5 INTRODUCTION CONTENTS INTRODUCTION ......4 VEHICLE IDENTIFICATION NUMBER ..6 HOW TO USE THIS MANUAL ....4 VEHICLE MODIFICATIONS/ALTERATIONS .
Page 6: Introduction
When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained tech- Congratulations on selecting your new Chrysler Group nicians and genuine parts, and cares about your satisfac- LLC vehicle. Be assured that it represents precision tion.
Page 7 INTRODUCTION 5...
Page 8: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This Owners Manual contains WARNINGS against op- erating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information.
Page 9: Vehicle Modifications/Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped VIN Location NOTE: It is illegal to remove or alter the VIN.
Page 11: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS ▫ Rearming Of The System ....19 A WORD ABOUT YOUR KEYS ... . .13 ▫...
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Sound Horn With Remote Lock ... .25 REMOTE STARTING SYSTEM — IF EQUIPPED . .32 ▫ Using The Panic Alarm ....26 ▫...
Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Seat Belt Extender .....81 LIFTGATE ......58 ▫...
Page 14 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Safety Checks You Should Make Inside The SAFETY TIPS ......124 Vehicle .
Page 15: A Word About Your Keys
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 A WORD ABOUT YOUR KEYS When released from the START position, the switch automatically returns to the ON/RUN position. Your vehicle is equipped with a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch.
Page 16: Key Fob
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key Fob The Key Fob operates the ignition switch. Insert the square end of the Key Fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion.
Page 17: Removing Key Fob From Ignition
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Removing Key Fob From Ignition WARNING! (Continued) Place the shift lever in PARK. Turn the Key Fob to the • Allowing children to be in a vehicle unattended is OFF position and then remove the Key Fob. dangerous for a number of reasons.
Page 18: Key-In-Ignition Reminder
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SENTRY KEY® CAUTION! The Sentry Key® Immobilizer system prevents unauthor- An unlocked car is an invitation to thieves. Always ized vehicle operation by disabling the engine. The remove the Key Fob from the ignition and lock all system does not need to be armed or activated.
Page 19: Replacement Keys
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 the bulb check, it indicates that someone used an invalid Replacement Keys Key Fob to start the engine. Either of these conditions will NOTE: Only Key Fobs that are programmed to the result in the engine being shut off after two seconds.
Page 20: Customer Key Programming
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE At the time of purchase, the original owner is provided General Information with a four-digit Personal Identification Number (PIN). The Sentry Key® system complies with FCC rules part 15 Keep the PIN in a secure location. This number is and with RSS-210 of Industry Canada.
Page 21: Rearming Of The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 power liftgate are disabled. The Vehicle Security Alarm To Arm The System provides both audible and visible signals, for the first Follow these steps to arm the Vehicle Security Alarm: three minutes, the headlights will turn on, the park lamps 1.
Page 22: To Disarm The System
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Push the LOCK button on the exterior Passive Entry • Cycle the vehicle ignition system out of the OFF Door Handle with a valid Key Fob available in the position. same exterior zone (refer to Keyless Enter-N-Go™ •...
Page 23: Tamper Alert
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 • When the Vehicle Security Alarm is armed, the interior Tamper Alert power door lock switches will not unlock the doors. If something has triggered the Vehicle Security Alarm in The Vehicle Security Alarm is designed to protect your your absence, the horn will sound three times and the vehicle;...
Page 24: Remote Keyless Entry (Rke) - If Equipped
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The lights will fade to off after approximately 30 seconds, REMOTE KEYLESS ENTRY (RKE) — IF or they will immediately fade to off once the ignition EQUIPPED switch is turned to ON/RUN from the OFF position. This system allows you to lock or unlock the doors and liftgate, and activate the Panic Alarm, optional power NOTE:...
Page 25: Using The Rke Transmitter
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Using The RKE Transmitter Three-button RKE transmitters will provide basic UN- LOCK, LOCK and PANIC functions. Key Fob With Three-Button RKE Transmitter Two RKE transmitters may be supplied with the vehicle. Vehicles built without the powered options will be equipped from the factory with three-button RKE trans- Key Fob With Three-Button RKE Transmitter mitters, and those built with power options will be...
Page 26: Remote Unlock Doors And Liftgate
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE (optional), power sliding doors, Remote Start feature Remote Unlock Doors And Liftgate (optional). Some features can be programmed to the Press and release the UNLOCK button on the RKE customers preferences. For example, flash headlights or transmitter once to unlock the driver’s side or twice to sound horn on LOCK.
Page 27: Sound Horn With Remote Lock
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 • For vehicles not equipped with the EVIC, the Remote NOTE: Pressing the LOCK button on the RKE transmit- Unlock feature can be enabled or disabled by perform- ter while you are inside the vehicle will activate the ing the following steps: Vehicle Security Alarm.
Page 28: Using The Panic Alarm
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the NOTE: Pressing the LOCK button on the RKE transmit- following steps: ter while you are in the vehicle will activate the Vehicle Security Alarm.
Page 29: Power Open/Close Power Liftgate - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 NOTE: If equipped with a rear interior switch on the left rear pillar, pushing this switch once will close the liftgate only. • When you turn off the Panic Alarm by pressing the The liftgate cannot be opened from this switch.
Page 30: Power Open/Close Right Power Sliding Door - If Equipped
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the vehicle is locked and the Vehicle Security Alarm is Turn Off Flash Lights With RKE Lock — If armed, pressing the LEFT Power Sliding Door button Equipped twice unlocks the power sliding door and disarms Ve- This feature will cause the turn signal lights to flash when hicle Security Alarm.
Page 31: Programming Additional Transmitters
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 2. Press and hold the UNLOCK button on a programmed Programming Additional Transmitters RKE transmitter for at least 4 seconds, but no longer If you do not have a programmed RKE transmitter, than 10 seconds.
Page 32 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Emergency Key Removal Remove Screw From Transmitter Case 2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves of the RKE transmitter apart. Make sure not to damage the seal during removal.
Page 33: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 4. To assemble the RKE transmitter case, snap the two halves together. General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: •...
Page 34: Remote Starting System - If Equipped
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If your RKE transmitter fails to operate from a normal NOTE: distance, check for these two conditions: • The vehicle must be equipped with an automatic 1. A weak battery in the transmitter. The expected life of transmission to be equipped with Remote Start.
Page 35 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 • Ignition key removed from ignition switch WARNING! (Continued) • Battery at an acceptable charge level • Keep Remote Keyless Entry (RKE) transmitters away from children. Operation of the Remote Start • RKE PANIC button not pressed System, windows, door locks or other controls •...
Page 36 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For security, power window and power sunroof op- The EVIC message stays active until the ignition is turned to the ON/RUN position. eration (if equipped) are disabled when the vehicle is in the Remote Start mode.
Page 37 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 • For vehicles not equipped with the Keyless Enter-N- To Exit Remote Start Mode And Drive The Vehicle Go™ feature, the ignition switch must be in the Before the end of the 15-minute cycle, press and release ON/RUN position in order to drive the vehicle.
Page 38 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Cancel Remote Start To Turn Off The Engine While In Remote Start Mode Remote Starting will also cancel if any of the following occur: Press and release the REMOTE START button one time or allow the engine to run for the entire 15 minute cycle.
Page 39: Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 DOOR LOCKS Manual Door Locks Lock the front doors by pushing down on the lock knobs on each door trim panel. If the lock knob is down when you shut either front door, the door will lock.
Page 40 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • When leaving the vehicle, always remove the Key Fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
Page 41: Power Door Locks - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Power Door Locks — If Equipped If you press the power door lock switch while the Key Fob is in the ignition, and any front door is open, the A power door lock switch is on each front door trim power locks will not operate.
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Door Locks — If Equipped When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). The auto door lock feature can be enabled or disabled by your authorized dealer per written request of the customer.
Page 43: Keyless Enter-N-Go
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 On vehicles equipped with the optional Electronic Ve- NOTE: hicle Information Center (EVIC), refer to “Electronic • Passive Entry may be programmed ON/OFF; refer to Vehicle Information Center (EVIC)/Personal Settings “Electronic Vehicle Information Center (EVIC)/ (Customer-Programmable Features)”...
Page 44 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If you unlock the doors using the Passive Entry door handles, but do NOT pull the handle, the doors will automatically lock after 60 seconds. To Unlock From The Driver’s Side: With a valid Passive Entry RKE transmitter within 5 ft (1.5 m) of the driver’s door handle, grab the driver’s front door handle to unlock the driver’s door automatically.
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 NOTE: If “Unlock All Doors 1st Press” is programmed Preventing Inadvertent Locking Of Passive Entry RKE all doors will unlock when you grab hold of the driver’s Transmitter In Vehicle front door handle. To select between “Unlock Driver To minimize the possibility of unintentionally locking a Door 1st Press”...
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Enter The Liftgate With a valid Passive Entry RKE transmitter within 5 ft (1.5 m) of the liftgate, cycle the handle to open the liftgate and pull the liftgate open with one fluid motion. NOTE: All doors will remain locked when the liftgate release handle is pressed regardless of the driver’s door unlock preference setting (“Unlock Driver Door 1st...
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 NOTE: • After pressing the door handle LOCK button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking.
Page 48: Windows
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Windows You can control either the front or rear windows using Power Vent Windows — If Equipped switches located on the driver’s door trim panel. The The Power Vent Window Switch located on the driver’s switches will operate only when the ignition switch is in door trim panel allows the driver to operate the two vent the ON/RUN or ACC position and during power acces-...
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 NOTE: Power Window switches will also remain active for up to 10 minutes after the ignition switch has been turned to OFF, depending upon the accessory delay setting. Opening a front door will cancel this feature. Power Window Lockout Switch —...
Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE switches will operate only when the ignition switch is in Auto-Down Feature — If Equipped the ON/RUN or ACC position and during power acces- The front window switches may be equipped with an sory delay.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 • Any impact due to rough road conditions may trigger Auto Up Feature With Anti-Pinch Protection — If Equipped the auto reverse function unexpectedly during auto- closure. If this happens, pull the switch lightly to the The front driver and front passenger switches may be first detent and hold to close window manually.
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open. Sliding Side Door Power Window Switch —...
Page 53: Sliding Side Door
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Wind Buffeting To keep your door operating properly, observe the fol- lowing guidelines: Wind buffeting can be described as the perception of • Always open the door smoothly. pressure on the ears or a helicopter-type sound in the ears.
Page 54: Power Sliding Side Door - If Equipped
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The left side sliding door cannot be opened Press the button on the RKE transmitter twice within five while the fuel door is open. This feature operates only seconds to open a power sliding door. When the door is when the sliding door is fully closed prior to opening the fully open, pressing the button twice within five seconds fuel door.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 To avoid unintentional operation of the power sliding doors from the rear seats, press the power sliding door master lock button, located in the overhead console, to disable the switches and handles for the rear seat passen- gers.
Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the power sliding side door is not in the full open or Power Sliding Side Door Open Flash close position, it will fully open when a power sliding The left and right exterior hazard lights will flash for 12 door switch is pressed.
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 You can turn the feature back on by repeating the previous procedure. Power Sliding Side Door Master Lock Switch To provide a safer environment for small children riding in the rear seats, the second row sliding door switches and handles may be overridden by pressing the OFF side of the Master Lock Out Switch located in the front overhead console.
Page 58: Sliding Side Door Child Protection Lock
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sliding Side Door Child Protection Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a Child Protection Door Lock system. NOTE: When the Child Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 NOTE: Protection Door Lock lever position. To avoid unin- tentional operation of the power sliding door from • After engaging the Child Protection Door Lock, always the rear seats, press the “OFF” Master Lock Out test the door from the inside to make certain it is in the Switch located in the front overhead console, next to desired position.
Page 60: Liftgate
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The power sliding side door switches will not open the To Disengage The Child Protection Door Lock power sliding doors if the vehicle is in gear or the 1. Open the sliding side door. vehicle speed is above 0 mph (0 km/h).
Page 61: Power Liftgate - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 To open the liftgate, press the liftgate release handle Power Liftgate — If Equipped located on the underside of the license plate bar and pull The power liftgate may be opened manually or by using the liftgate open with one fluid motion.
Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power liftgate may be closed by pressing the button, located in the upper left trim in the liftgate opening. Pushing once will only close the liftgate. This button cannot be used to open the liftgate. Overhead Console Master Power Switch 1 —...
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 • There are also pinch sensors attached to the side of the When the RKE transmitter button is pressed and the Flash Lights feature is enabled, the tail lights will flash liftgate opening. Light pressure anywhere along these and several audible beeps will occur to signal that the strips will cause the liftgate to return to the open liftgate is opening or closing.
Page 64: Occupant Restraints
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The power liftgate will not operate in temperatures WARNING! (Continued) below −12°F (−24°C) or temperatures above 143°F • If you are required to drive with the liftgate open, (62°C). Be sure to remove any buildup of snow or ice make sure that all windows are closed, and the from the liftgate before pressing any of the power climate control blower switch is set at high speed.
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 • Supplemental Active Head Restraints (AHR) located which lock the seat belt webbing into position by on top of the front seats (integrated into the head extending the belt all the way out and then adjusting restraint) the belt to the desired length to restrain a child seat or secure a large item in a seat...
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can take to minimize the ride properly buckled up in the rear seat. Never allow risk of harm from a deploying air bag: children to slide the shoulder belt behind them or under their arm.
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 4. Do not lean against the door or window. If your WARNING! (Continued) vehicle has side air bags, and deployment occurs, the • Being too close to the steering wheel or instrument side air bags will inflate forcefully into the space panel during Advanced Front Air Bag deployment between you and the door.
Page 68: Lap/Shoulder Belts
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and they WARNING! (Continued) can reduce the seriousness of injuries in a collision. Some • In a collision, you and your passengers can suffer of the worst injuries happen when people are thrown much greater injuries if you are not properly buck- from the vehicle.
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 WARNING! WARNING! (Continued) • Wearing your belt in the wrong place could make • It is dangerous to ride in a cargo area, inside or your injuries in a collision much worse. You might outside of a vehicle.
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is near the seatback of the WARNING! front seats and next to your arm in the rear seats. • A belt that is worn under your arm is dangerous. Grasp the latch plate and pull out the belt.
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you.
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen.
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 6. To release the belt, push the red button on the buckle. Third Row Center Shoulder Belt Instructions The belt will automatically retract to its stowed posi- The shoulder belt for the third row center seat is located tion.
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seats and the second row outboard seats, the shoulder belt anchorage can be adjusted upward or down- ward to help position the belt away from your neck. The upper anchorage can be adjusted upward by pushing anywhere on the anchorage.
Page 75: Seat Belts In Passenger Seating Positions
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Seat Belts In Passenger Seating Positions Second Row Quad Seating Driver Center Passenger The seat belts in the passenger seating positions are equipped with an Automatic Locking Retractor (ALR) or First Row a cinching latch plate which are used to secure a child Second Row restraint system.
Page 76: Automatic Locking Retractor Mode (Alr) - If Equipped
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the passenger seating position is equipped with an position that has a belt with this feature. Children 12 ALR and is being used for normal usage: years old and under should always be properly re- strained in a vehicle with a rear seat.
Page 77: Energy Management Feature
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 This safety belt system has a retractor assembly that is WARNING! designed to release webbing in a controlled manner. This • The belt and retractor assembly must be replaced if feature is designed to help reduce the belt force acting on the occupant’s chest.
Page 78: Supplemental Active Head Restraints (Ahr)
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The pretensioners are triggered by the Occupant Re- the Active Head Restraints (AHR) to deploy. If a rear straint Controller (ORC). Like the air bags, the preten- impact requires deployment, both the driver and front sioners are single use items.
Page 79 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 CAUTION! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
Page 80 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Grasp the deployed AHR from the rear seat. 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. Hand Positioning Points On AHR 2.
Page 81 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 AHR In Reset Position 3 — Final Downward Movement To Engage Locking Mechanism NOTE: 4. The AHR front soft foam and trim half should lock • If you have difficulties or problems resetting the Active into the back decorative plastic half.
Page 82: Enhanced Seat Belt Use Reminder System (Beltalert®)
Reminder Light and sounding an intermittent chime. BeltAlert® can be enabled or disabled by your autho- Once the sequence starts, it will continue for the entire rized dealer. Chrysler Group LLC does not recommend duration or until the respective seatbelts are fastened. deactivating BeltAlert®.
Page 83: Seat Belts And Pregnant Women
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Seat Belts And Pregnant Women WARNING! We recommend that pregnant women use the seat belts Using a seat belt extender when not needed can in- throughout their pregnancy. Keeping the mother safe is crease the risk of injury in a collision.
Page 84 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The Driver and Passenger Advanced Front Air Bags are certified to new Federal regulations. The Advanced Front Air Bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on the severity and type of collision.
Page 85: Air Bag System Components
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 • Air Bag Warning Light and rear passengers sitting next to a window. The SABIC air bags are located above the side windows and their • Steering Wheel and Column covers are also labeled: SRS AIRBAG. •...
Page 86: Advanced Front Air Bag Features
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Advanced Front Air Bag Features WARNING! The Advanced Front Air Bag system has multistage • No objects should be placed over or near the air driver and front passenger air bags. This system provides bag on the instrument panel, because any such output appropriate to the severity and type of collision as objects could cause harm if the vehicle is in a...
Page 87 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Supplemental Seat-Mounted Side Air Bags (SAB) When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag Supplemental Seat-Mounted Side Air Bags (SAB) may deploys independently;...
Page 88 86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Side Air Bag Inflatable Curtain WARNING! (SABIC) Do not use accessory seat covers or place objects SABIC air bags may offer side-impact and vehicle roll- between you and the side air bags; the performance over protection to front and rear seat outboard occupants could be adversely affected and/or objects could be in addition to that provided by the body structure.
Page 89 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 • Being too close to the SAB and SABIC air bags during WARNING! (Continued) deployment could cause you to be severely injured or • Do not use accessory seat covers or place objects killed.
Page 90: Air Bag Deployment Sensors And Controls
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAB and SABIC air bags are a supplement to the seat belt Knee Impact Bolsters restraint system. Occupants, including children who are The Knee Impact Bolsters help protect the knees of the up against or very close to SAB or SABIC air bags can be driver and front passenger, and position the front occu- seriously injured or killed.
Page 91 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 bags, SABs, Supplemental Driver Side Knee Air Bag, and Side Knee Air Bag may deploy in crashes with little front seat belt pretensioners, as required, depending on vehicle front-end damage but that produce a severe several factors, including the severity and type of impact.
Page 92 90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE position, in the ACC position, or not in the ignition, the WARNING! air bag system is not on and the air bags will not inflate. Ignoring the Air Bag Warning Light in your instru- The ORC contains a backup power supply system that ment panel could mean you won’t have the air bags may deploy the air bags even if the battery loses power or...
Page 93 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 are possible, based on several factors, including the Supplemental Driver Side Knee Air Bag. The trim cover collision type and severity. The steering wheel hub trim separates and folds out of the way allowing the air bag to cover and the upper right side of the instrument panel inflate to the full size.
Page 94 92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE at a very high speed and with such a high force that it positioned in the area where the side curtain air bag could injure you if you are not seated properly, or if items inflates.
Page 95 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 event the ORC will determine whether to have the If A Deployment Occurs Enhanced Accident Response System perform the follow- The Advanced Front Air Bags are designed to deflate ing functions: immediately after deployment. •...
Page 96 94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE However, if you haven’t healed significantly within a Do not drive your vehicle after the air bags have de- few days, or if you have any blistering, see your doctor ployed. If you are involved in another collision, the air immediately.
Page 97 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 Maintaining Your Air Bag System WARNING! (Continued) • Do not attempt to modify any part of your air bag WARNING! system. The air bag may inflate accidentally or may • Modifications to any part of the air bag system not function properly if modifications are made.
Page 98: Event Data Recorder (Edr)
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag Warning Light NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The air bags may You will want to have the air bags ready to not be ready to inflate for your protection.
Page 99: Child Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 • Whether or not the driver and passenger safety belts To read data recorded by an EDR, special equipment is were buckled/fastened; required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, •...
Page 100 98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Before buying any restraint system, make sure that it has WARNING! a label certifying that it meets all applicable Safety Standards. You should also make sure that you can install In a collision, an unrestrained child can become a it in the vehicle where you will use it.
Page 101 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Infants and Toddlers Children who are two years old or Either an Infant Carrier or a Convertible younger and who have not reached the Child Restraint, facing rearward in the height or weight limits of their child re-...
Page 102 100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Child Restraints WARNING! Safety experts recommend that children ride rearward- • Never place a rear facing infant seat in front of an facing in the vehicle until they are two years old or until air bag.
Page 103 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 have outgrown the rear-facing weight or height limit of WARNING! their rear-facing convertible child seat. Children should • Improper installation can lead to failure of an remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height infant or child restraint.
Page 104 102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large For Booster Seats 4. Is the lap part of the belt as low as possible, touching the child’s thighs and not their stomach? Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend 5.
Page 105 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 Recommendations For Attaching Child Restraints Use any attachment method shown with an “X” Below Combined LATCH – Weight of the LATCH – Restraint Type Lower Anchors Seat Belt + Top Child + Child Lower Anchors Seat Belt Only + Top Tether...
Page 106 104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors And Tethers For Children (LATCH) Your vehicle is equipped with the child restraint anchor- Restraint System age system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCH- equipped child seats.
Page 107 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 LATCH Positions For Installing Child Restraints In This Vehicle Second Row Bench Lower Anchorage Symbol 2 anchorages per seating Second Row Captains Chairs position • Lower Anchorage Symbol 2 anchorages per seat- Top Tether Anchorage Symbol ing position •...
Page 108 106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint LATCH Positions What is the weight limit (child’s 65 lbs (29.5 kg) Use the LATCH anchorage system weight + weight of the child restraint) until the combined weight of the child for using the LATCH anchorage sys- and the child restraint is 65 lbs tem to attach the child restraint?
Page 109 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 107 Can two child restraints be attached Never “share” a LATCH anchorage using a common lower LATCH an- with two or more child restraints. If chorage? the center position does not have dedicated LATCH lower anchorages, use the seat belt to install a child seat in the center position next to a child seat using the LATCH anchorages in...
Page 110 108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint.
Page 111 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 109 Locating The LATCH Anchorages In addition, there are tether strap anchors lo- cated behind each rear seatback, near to the floor. LATCH Anchorages (Third Row 60/40 Anchorages Shown) LATCH Anchorages (Third Row 60/40 Anchorage Shown)
Page 112: Commercial Cargo Vehicles
110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH-compatible child restraint systems will be Always follow the directions of the child restraint manu- equipped with a rigid bar or a flexible strap on each side. facturer when installing your child restraint. Not all child Each will have a hook or connector to attach to the lower restraint systems will be installed as described here.
Page 113 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 111 Always follow the directions of the child restraint 3. Place the child seat between the lower anchorages for manufacturer when installing your child restraint. Not that seating position. For some second row seats, you all child restraint systems will be installed as described may need to recline the seat and/or raise the head here.
Page 114 112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. Tighten all of the straps as you push the child restraint the child’s reach. If the buckled seat belt interferes with rearward and downward into the seat. Remove slack the child restraint installation, instead of buckling it in the straps according to the child restraint manufac- behind the child restraint, route the seat belt through the turer’s instructions.
Page 115 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 113 be “switched” into a locked mode by pulling all of the WARNING! (Continued) webbing out of the retractor and then letting the webbing • Child restraint anchorages are designed to with- retract back into the retractor. If it is locked, the ALR will stand only those loads imposed by correctly-fitted make a clicking noise while the webbing is pulled back child restraints.
Page 116 114 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Systems for Installing Child Restraints in this Vehicle Second Row Bench Second Row Captains Chair...
Page 117 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 115 Lap/Shoulder Belt Systems What is the weight limit (child’s Weight limit of the Child Re- Always use the tether anchor when weight + weight of the child restraint) straint using the seat belt to install a forward for using the Tether Anchor with the facing child restraint, up to the recom- seat belt to attach a forward facing...
Page 118 116 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing A Child Restraint With A Switchable 5. To lock the seat belt, pull down on the shoulder part of Automatic Locking Retractor (ALR) the belt until you have pulled all the seat belt webbing out of the retractor.
Page 119 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 117 strap. See the section “Installing Child Restraints rear-most position to make room for the child seat. Using the Top Tether Anchorage” for directions to You may also move the front seat forward to allow attach a tether anchor.
Page 120 118 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE strap. Refer to “Installing Child Restraints Using The If the belt still cannot be tightened after you shorten the Top Tether Anchorage” for directions to attach a tether buckle, disconnect the latch plate from the buckle, turn anchor.
Page 121 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 119 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts.
Page 122 120 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap.
Page 123: Commercial Cargo Vehicles (No Factory Installed Rear Seats) - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 121 COMMERCIAL CARGO VEHICLES (NO FACTORY INSTALLED REAR SEATS) — IF EQUIPPED Commercial cargo vehicles are not designed for use as a family vehicle and are not intended for carrying children in the front passenger seat. However, if you must carry a child in a vehicle without a rear seat, the passenger seat should be moved to the full rearward position and the child must be in a proper restraint system based on its...
Page 124: Restraining Infants And Small Children In Commercial Cargo Vehicles
122 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Restraining Infants And Small Children In NOTE: Ensure that the child restraint tether strap is Commercial Cargo Vehicles centered between the headrest supports underneath the head rest. There are different sizes and types of restraints for children from newborn size to the child almost large 3.
Page 125: Engine Break-In Recommendations
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 123 ENGINE BREAK-IN RECOMMENDATIONS conditions under which vehicle operations will occur. For the recommended viscosity and quality grades, refer to A long break-in period is not required for the engine and “Maintenance Procedures” in “Maintaining Your Ve- drivetrain (transmission and axle) in your vehicle.
Page 126: Things To Know Before Starting Your Vehicle Safety Tips
124 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS WARNING! (Continued) Transporting Passengers • Be sure everyone in your vehicle is in a seat and using a seat belt properly. NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. Exhaust Gas WARNING! WARNING! •...
Page 127: Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 125 damaged, deteriorated, or mispositioned parts. Open WARNING! (Continued) seams or loose connections could permit exhaust fumes • If you are required to drive with the trunk/liftgate/ to seep into the passenger compartment. In addition, rear doors open, make sure that all windows are inspect the exhaust system each time the vehicle is raised closed and the climate control BLOWER switch is...
Page 128 126 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag Warning Light Floor Mat Safety Information Always use floor mats designed to fit the footwell of your The light should come on and remain on for vehicle. Use only floor mats that leave the pedal area four to eight seconds as a bulb check when the unobstructed and that are firmly secured so that they ignition switch is first turned ON.
Page 129 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 127 WARNING! (Continued) WARNING! (Continued) • Never place or install floor mats or other floor • Always make sure that objects cannot fall into the coverings in the vehicle that cannot be properly driver footwell while the vehicle is moving.
Page 130: Periodic Safety Checks You Should Make Outside The Vehicle
128 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside Door Latches The Vehicle Check for positive closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
Page 131: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS ▫ Tilt Mirrors In Reverse (Available With Memory MIRRORS ......136 Seat Only) —...
Page 132 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Phone Call Features ....161 ▫ Heated Seats — If Equipped ....193 ▫...
Page 133 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 ▫ Setting Memory Positions And Linking RKE ▫ Multifunction Lever ....231 Transmitter To Memory ....221 ▫...
Page 134 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Rain Sensing Wipers — If Equipped ..237 ▫ ParkSense® Sensors ....248 ▫...
Page 135 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 ▫ Security ......271 OVERHEAD CONSOLES ....260 ▫...
Page 136 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Ignition Off Operation ....277 ▫ Driver Seatback Storage — If Equipped ..288 ▫...
Page 137 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 ▫ Rechargeable Flashlight ....301 ROOF LUGGAGE RACK — IF EQUIPPED ..304 ▫ Deploying The Crossbars ....305 REAR WINDOW FEATURES .
Page 138: Mirrors
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
Page 139: Automatic Dimming Mirror - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated.
Page 140: Outside Mirrors
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors Driver’s Outside Automatic Dimming Mirror — If Equipped To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight The driver’s outside mirror will automatically adjust for overlap of the view obtained on the inside mirror.
Page 141: Power Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Power Mirrors — If Equipped The power mirror controls consist of mirror select but- tons and a four-way mirror control switch. To adjust a The power mirror controls are located on the driver-side mirror, press either the L (left) or R (right) to select the door trim panel.
Page 142: Heated Mirrors - If Equipped
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Mirrors — If Equipped NOTE: The Tilt Mirrors in Reverse feature is not enabled when delivered from the factory. The Tilt Mirrors in Reverse feature can be enabled or disabled in the Elec- These mirrors are heated to melt frost or ice.
Page 143: Illuminated Vanity Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Resetting the Power Folding Outside Mirrors Illuminated Vanity Mirrors — If Equipped You may need to reset the power folding mirrors if the An illuminated vanity mirror is located on the sun visor. following occurs: To use the mirror, rotate the sun visor down and swing the mirror cover upward.
Page 144: Blind Spot Monitoring (Bsm) - If Equipped
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE BLIND SPOT MONITORING (BSM) — IF EQUIPPED The Blind Spot Monitoring (BSM) system uses two radar- based sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.) that enter the blind spot zones from the rear/front/side of the vehicle.
Page 145 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Automatic Transmission Vehicles NOTE: • The BSM system does NOT alert the driver about The BSM system sensors operate when the vehicle is in any forward gear or REVERSE and enters stand-by mode rapidly approaching vehicles that are outside the de- when the vehicle is in PARK.
Page 146 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sensor Locations BSM Warning Light The BSM system notifies the driver of objects in the The BSM system monitors the detection zone from three detection zones by illuminating the BSM warning light different entry points (side, rear, front) while driving to located in the outside mirrors in addition to sounding an see if an alert is necessary.
Page 147 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h).
Page 148 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Overtaking Traffic If you pass another vehicle slowly (with a relative speed of less than 15 mph (24 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated.
Page 149 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Overtaking/Passing Stationary Objects The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, etc.
Page 150: Rear Cross Path
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicle’s mirrors, glance over your shoulder, and use your turn signal before changing lanes.
Page 151 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When RCP is on and the vehicle is in REVERSE, the driver is alerted using both the visual and audible alarms, including reducing the radio volume.
Page 152: Modes Of Operation
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Modes Of Operation Blind Spot Alert Lights/Chime Modes Of Operation With EVIC When operating in Blind Spot Alert Lights/Chime mode, the BSM system will provide a visual alert in the appro- Three selectable modes of operation are available in the priate side view mirror based on a detected object.
Page 153: Uconnect® Phone - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 When the system is in RCP, the system shall respond with phone using simple voice commands (e.g., “Call” both visual and audible alerts when a detected object is “Mike” “Work” or “Dial” “248-555-1212”). Your present.
Page 154 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect® Phone allows you to transfer calls between WARNING! the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system’s Any voice commanded system should be used only microphone for private conversation.
Page 155: Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Voice Command Button Operation Voice commands can be used to operate the Uconnect® Actual button location may vary with the ra- Phone and to navigate through the Uconnect® Phone dio. The individual buttons are described in the menu structure.
Page 156 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE part of the command when you are asked for it. For To activate the Uconnect® Phone, simply press the example, you can use the compound form voice com- button and follow the audible prompts for directions. mand “Phonebook New Entry,”...
Page 157 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 The following are general phone to Uconnect® Phone You will then be asked to give your mobile phone a pairing instructions: priority level between one and seven, with one being the highest priority. You can pair up to seven mobile phones 1.
Page 158 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The system will prompt you to say the number you or downloaded phonebook. To learn how to store a want to call. name in the phonebook, refer to “Add Names to Your Uconnect®...
Page 159 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 • Automatic download and update, if supported, begins • This downloaded phonebook cannot be edited or as soon as the Bluetooth® wireless phone connection is deleted on the Uconnect® Phone. These can only be made to the Uconnect®...
Page 160 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, enter the number designation (e.g., Edit Uconnect® Phonebook Entries “Home,” “Work,” “Mobile,” or “Other”). This will NOTE: Editing phonebook entries is recommended allow you to store multiple numbers for each phone- when the vehicle is not in motion.
Page 161 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 • After you enter the Phonebook Delete menu, you will After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in then be asked for the name of the entry that you wish the phonebook, call the number you just edited, or return to delete.
Page 162 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete/Erase “All” Uconnect® Phonebook Entries List All Names In The Uconnect® Phonebook • Press the • Press the button to begin. button to begin. • After the “Ready” prompt and the following beep, say •...
Page 163: Phone Call Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Phone Call Features Answer Or Reject An Incoming Call — Call Currently In Progress The following features can be accessed through the Uconnect® Phone if the feature(s) are available on your If a call is currently in progress and you have another mobile service plan.
Page 164 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE in progress. To go back to the first call, refer to “Toggling Conference Call Between Calls” in this section. To combine two calls, refer When two calls are in progress (one active and one on to “Conference Call”...
Page 165 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Call Termination Call Continuation To end a call in progress, momentarily press the but- Call continuation is the progression of a phone call on the ton. Only the active call(s) will be terminated and if there Uconnect®...
Page 166: Uconnect® Phone Features
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect® Phone Features Emergency Assistance If you are in an emergency and the mobile phone is Language Selection reachable: To change the language that the Uconnect® Phone is • Pick up the phone and manually dial the emergency using: number for your area.
Page 167 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 NOTE: WARNING! • The emergency number dialed is based on the country To use your Uconnect® Phone System in an emer- where the vehicle is purchased (911 for the U.S. and gency, your mobile phone must be: Canada and 060 for Mexico).
Page 168 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: You should program the desired Towing Assis- Working With Automated Systems tance phone number using the Voice Command system. This method is used in instances where one generally has To do this, press the button and say “Setup,” followed by to press numbers on the mobile phone keypad while “Towing Assistance.”...
Page 169 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 “Send,” is also to be used for navigating through an Barge In — Overriding Prompts automated customer service center menu structure, and The “Voice Command” button can be used when you to leave a number on a pager. wish to skip part of a prompt and issue your voice command immediately.
Page 170 168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone And Network Status Indicators NOTE: Certain brands of mobile phones do not send the dial ring to the Uconnect® Phone to play it on the vehicle If available on the radio and/or on a premium display audio system, so you will not hear it.
Page 171: Advanced Phone Connectivity
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 To un-mute the Uconnect® Phone: If you would like to connect or disconnect the Bluetooth® connection between your mobile phone and the • Press the button. Uconnect® Phone System, follow the instructions de- •...
Page 172: Things You Should Know About Your Uconnect® Phone
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Select Another Mobile Phone Delete Uconnect® Phone Paired Mobile Phones • Press the This feature allows you to select and start using another button to begin. phone paired with the Uconnect® Phone. • After the “Ready” prompt and the following beep, say •...
Page 173 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Voice Training best results, the Voice Training session should be com- pleted when the vehicle is parked with the engine For users experiencing difficulty with the system recog- running, all windows closed, and the blower fan nizing their voice commands or numbers, the Uconnect®...
Page 174 172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Fully closed windows Voice Command • For best performance, adjust the rearview mirror to • Dry weather condition provide at least ½ inch (1 cm) gap between the • Even though the system is designed for users speaking overhead console (if equipped) and the mirror.
Page 175 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 • Numbers must be spoken in single digits. “800” must • Fully Closed Windows be spoken “eight-zero-zero” not “eight hundred.” • Dry Weather Conditions • You can say “O” (letter “O”) for “0” (zero). •...
Page 176 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Text Reply After reading a message, you can “Reply” or “Forward” the message using Uconnect® Phone. Uconnect® Phone can read or send new messages on your phone. Send Messages: Read Messages: You can send messages using Uconnect® Phone. To send a new message: If you receive a new text message while your phone is connected to Uconnect®...
Page 177 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 List of Preset Messages: 11. See You in 15 minutes. 1. Yes. 12. I am on my way. 2. No. 13. I’ll be late. 3. Where are you? 14. Are you there yet? 4.
Page 178 176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Voice Text Reply Incoming Announcement Bluetooth® Communication Link ON/OFF Mobile phones have been found to lose connection to the Uconnect® Phone. When this happens, the connection Turning the Voice Text Reply Incoming Announcement can generally be reestablished by switching the phone OFF will stop the system from announcing the new off/on.
Page 179 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177...
Page 180 178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 181 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179...
Page 182 180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate (s) Primary Alternate (s) zero call cancel three confirmation prompts four continue five delete dial seven download eight edit nine emergency star (*) English plus (+) erase all pound (#) Espanol add location...
Page 183 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 Voice Commands Voice Commands Primary Alternate (s) Primary Alternate (s) help previous home record again language redial list names return to main menu return or main menu list phones select phone select mobile send mute set up...
Page 184: General Information
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information VOICE COMMAND — IF EQUIPPED This device complies with Part 15 of the FCC rules and Voice Command System Operation RSS 210 of Industry Canada. Operation is subject to the following conditions: The Uconnect®...
Page 185 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Pressing the Voice Command button while the WARNING! system is speaking is known as “barging in.” The system will be interrupted, and after the beep, you can add or Any voice commanded system should be used only change commands.
Page 186: Commands
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To hear the first available Menu, press the Voice Com- Main Menu mand button and say “Help” or “Main Menu.” Start a dialogue by pressing the Voice Command button. You may say “Main Menu” to switch to the Commands main menu.
Page 187 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 • “Menu Radio” (to switch to the radio menu) Radio AM • “Main Menu” (to switch to the main menu) To switch to the AM band, say “AM” or “Radio AM.” In this mode, you may say the following commands: Satellite Radio •...
Page 188 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Disc Mode Bluetooth® Streaming (BT) Mode To switch to the disc mode, say “Disc.” In this mode, you To switch to Bluetooth® Streaming (BT) mode, say may say the following commands: “Bluetooth Streaming.” In this mode, you may say the following commands: •...
Page 189 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 • “Switch to system setup” – “Continue” (to continue recording) • “Main menu setup” – “Delete” (to delete the recording) • “Switch to setup” • “Play Memos” (to play previously recorded memos) — During the playback you may press the Voice Com- In this mode, you may say the following commands: mand...
Page 190: Voice Training
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Training SEATS For users experiencing difficulty with the system recog- Seats are a part of the Occupant Restraint System of the nizing their voice commands or numbers the Uconnect® vehicle. Voice “Voice Training” feature may be used. WARNING! 1.
Page 191: Power Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 Power Seats — If Equipped Some models may be equipped with eight-way power seats for the driver and front passenger. The power seat switches are located on the outboard side of the seat. The switches control the movement of the seat cushion and the seatback.
Page 192 190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Adjusting a seat while driving may be dangerous. Do not place any article under a power seat or Moving a seat while driving could result in loss of impede its ability to move as it may cause damage to control which could cause a collision and serious the seat controls.
Page 193 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 Tilting The Seat Up Or Down WARNING! The angle of the seat cushion can be adjusted in four • Adjusting a seat while driving may be dangerous. directions. Pull upward or push downward on the front Moving a seat while driving could result in loss of or rear of the seat switch, the front or rear of the seat control which could cause a collision and serious...
Page 194: Power Lumbar - If Equipped
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.
Page 195: Heated Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 Heated Seats — If Equipped Vehicles Equipped With Remote Start On some models, the front and rear seats may be On models that are equipped with remote start, the equipped with heaters located in the seat cushions. driver’s heated seat can be programmed to come on during a remote start.
Page 196 194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can choose from HIGH, LOW or OFF heat settings. Rear Heated Seats Amber indicator lights in each switch indicate the level of On some models, the second row seats are equipped with heat in use.
Page 197: Manual Front/Second Row Seat Adjuster
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 You can choose from HIGH, LOW or OFF heat settings. Manual Front/Second Row Seat Adjuster Amber indicator lights in each switch indicate the level of Both front seats are adjustable forward or rearward. The heat in use.
Page 198: Manual Reclining Seats - If Equipped
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE While sitting in the seat, pull up on the handle and slide Manual Reclining Seats — If Equipped the seat forward or rearward. Release the bar once you For models equipped with manual reclining seats, the have reached the desired position.
Page 199: Head Restraints
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 To recline, lean forward slightly, lift the lever, then push WARNING! back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its The head restraints for all occupants must be prop- normal position.
Page 200 198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the AHR. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts.
Page 201 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 Active Head Restraint (Normal Position) Active Head Restraint (Tilted) NOTE: • The head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer.
Page 202 200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In the event of deployment of an Active Head Re- WARNING! (Continued) straint, refer to “Occupant Restraints/Resetting Active • Active Head Restraints may be deployed if they are Head Restraints (AHR)” in “Things To Know Before struck by an object such as a hand, foot or loose Starting Your Vehicle”...
Page 203: Stow 'N Go® Seating - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 Head Restraints — Third Row The head restraint in the center position can be raised and lowered for tether routing. Refer to “Occupant Re- straints” in “Things To Know Before Starting Your Ve- hicle”...
Page 204 202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Seat will not stow in the storage bin unless the 5. Pull upward on the seatback recliner lever located on armrests are raised. the outboard side of the seat. 4. Slide the storage bin locking mechanism to the “LOCK”...
Page 205 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 Non-Adjustable Head Restraint Automatic Folding Seatback The seat will automatically tumble into position for easy storage.
Page 206 204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tumbled Second Row Seat Seat In Storage Bin 6. Push the seat into the storage bin. 7. Close the storage bin cover.
Page 207 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 To Unstow Second Row Seats CAUTION! 1. Pull up on the storage bin latch to open the cover. The storage bin cover must be locked and flat to 2. Pull up on the strap to lift the seat out of the storage avoid damage from contact with the front seat tracks, bin and push the seat rearward to latch the seat which have minimal clearance to the cover.
Page 208 206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Sitting in a seat with the head restraint in its lowered position could result in serious injury or death in a collision. Always make sure the head restraints are in their upright positions when the seat is to be occupied.
Page 209 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 Easy Entry Second Row The second row Stow ’n Go® seats allow easy entry to the third row seat or rear cargo area. Pull up on the seatback recliner lever on the outboard side of the seat.
Page 210: Quad Seats - If Equipped
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The seat will automatically fold into position for easy entry into the third row. WARNING! In the event of a collision you could be injured if the seat is not fully latched. Quad Seats — If Equipped Both Quad seats are adjustable forward or rearward.
Page 211 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked.
Page 212 210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold-Flat Easy Entry To fold the seat, lift the recliner lever to the full upward The Quad seats can be tilted forward for easy entry into position and push the seatback forward until it rests on the third row.
Page 213 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 For passengers seated in the third row, there is a pull Removal strap located on the outboard side of the seat near the The Quad seats can be removed if additional storage is bottom of the seat back.
Page 214: Second Row Bench Seat - If Equipped
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second Row Bench Seat — If Equipped indicator button pops up when the seat is unlocked. The seat assembly can now be removed from the vehicle and While the bench seat does not stow in the floor, it is moved on its Easy Out®...
Page 215: Third Row Power Recline - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 To reinstall the seat, align the seat into the detent positions on the floor. Squeeze the release handle and rotate upward until the lock indicator button returns into the handle. WARNING! If not properly latched, the bench seats could become loose.
Page 216 214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Lower the head restraint by pulling on the release strap marked “1” located on the outboard side of the head restraint. One Touch Folding Seat Third Row The rear switch bank allows multiple power folding and unfolding positions for the third row seats.
Page 217 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 NOTE: • Disconnect the center shoulder belt from the small buckle and lower the head restraints before attempting to fold/stow the power third row seats. • To abort seat operation while seat is in motion, press a different seat position selector switch to stop the seat.
Page 218: Manually Folding Third Row Seats - If Equipped
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manually Folding Third Row Seats — If Equipped 1. Lower the center head restraint down to the seatback by pushing the button on the guide and pushing the head restraint down. 2. Lower the outboard head restraints by pulling on the release strap marked “1”...
Page 219 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 3. Pull release strap marked “2” located on the rear of the 4. Pull release strap marked “3” to release the anchors. seat to lower the seatback. Release Strap “3” Release Strap “2”...
Page 220 218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Pull release strap marked “4” and tumble the seat rearward into the storage bin. Stowed Third Row Seat Release Strap “4”...
Page 221 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 To Unfold Third Row Seats WARNING! (Continued) 1. Pull up on the assist strap to lift the seat out of the • Sitting in a seat with the head restraint in its storage bin and push the seat forward until the lowered position could result in serious injury or anchors latch.
Page 222: Plastic Grocery Bag Retainer Hooks
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Plastic Grocery Bag Retainer Hooks Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all rear seats and some front seats. The floor supports the partial weight of the bagged goods.
Page 223: Setting Memory Positions And Linking Rke
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 Setting Memory Positions And Linking RKE 6. Press and release the SET (S) button located on the Transmitter To Memory driver’s door. NOTE: Each time the SET (S) button and a numbered 7. Within five seconds, press and release MEMORY button (1 or 2) is pressed, you erase the memory settings button 1 or 2 on the driver’s door.
Page 224 222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 11. Repeat the above steps to set the next Memory 1, or 2). When a recall is cancelled, the driver’s seat, and position using the other numbered Memory button or the pedals stop moving. A delay of one second will occur to link another RKE transmitter to memory.
Page 225: Easy Entry/Exit Seat (Available With Memory Seat Only)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 • When you remove the key from the ignition switch, To disable another RKE transmitter linked to either the driver seat will move about 2.4 in (60 mm) rear- Memory Position, repeat Steps 1 to 5 for each RKE ward if the driver seat position is greater than or equal transmitter.
Page 226: To Open And Close The Hood
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Each stored memory setting will have an associated Easy Entry and Easy Exit Position. NOTE: The Easy Entry/Easy Exit feature can be enabled or disabled through the programmable features in the Electronic Vehicle Information Center (EVIC). If your vehicle is not equipped with an EVIC, your dealership can activate/deactivate this feature for you.
Page 227 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 12 in (30 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
Page 228: Lights
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Headlight Switch The headlight switch is located on the left side of the instrument panel. The switch controls the operation of the headlights, parking lights, instrument panel lights, interior lights and the fog lights. Headlight Switch With Halo Control Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation.
Page 229: Automatic Headlights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 Automatic Headlights — If Equipped on when windshield wipers are on may be found on vehicles equipped with an automatic headlight system. This system automatically turns your headlights on or off based on ambient light levels. To turn the system on, turn NOTE: The headlights on with wipers will only operate the headlight switch to the extreme counterclockwise if it is selected from the Customer-Programmable Fea-...
Page 230: Lights-On Reminder
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE headlights or parking lights are turned back on or the Lights-On Reminder ignition switch is turned ON, the delay will be cancelled. If the headlights or the parking lights are left on, or if the When exiting the vehicle the driver can choose to have dimmer control is in the extreme top position after the the headlights remain on for 30, 60 or 90 seconds or not...
Page 231: Front Fog Lights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 Front Fog Lights — If Equipped To activate the front fog lights, turn on the parking lights or the low beam headlights and push in the headlight switch control knob. Pressing the headlight switch control knob in a second time will turn the front fog lights off.
Page 232 230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lighting On NOTE: The key must be out of the ignition switch or the ignition switch must be in the OFF position for this Rotate the left dimmer control completely upward to the feature to operate.
Page 233: Multifunction Lever
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 The Halo control switch is located to the right of the Multifunction Lever dimmer switch. The multifunction lever is located on the left side of the steering column. Halo Control To activate the Halo lights, rotate the Halo Multifunction Lever switch control upward or downward to in- crease or decrease the lighting.
Page 234: Turn Signals
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The multifunction lever controls the: Turn Signal Warning • Turn Signals If the vehicle electronics sense that the vehicle has traveled at over 18 mph (29 km/h) for about 1 mile • Headlight Beams Low/High (1.6 km) with the turn signals on, a chime will sound to •...
Page 235: Flash-To-Pass
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 Flash-To-Pass NOTE: Broken, muddy or obstructed headlights and taillights of vehicles in the field of view will cause You can signal another vehicle with your headlights by headlights to remain on longer (closer to the vehicle). lightly pulling the multifunction lever toward you.
Page 236: Battery Protection
234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Push the multifunction lever away from you to switch 3. Rotate the headlight switch clockwise from the AUTO the headlights to the high beam position. Refer to to the on position. “Multifunction Lever” in this section for further infor- Battery Protection mation.
Page 237: Windshield Wiper And Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 WINDSHIELD WIPER AND WASHERS NOTE: Always remove any buildup of snow that pre- vents the windshield wiper blades from returning to the The wipers and washers are operated by a switch within off position. If the windshield wiper switch is turned off the multifunction lever.
Page 238: Intermittent Wiper System
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System Windshield Washers Use the intermittent wiper when weather conditions To use the Washer, push on the end of the lever to the make a single wiping cycle with a variable pause be- second detent and hold while spray is desired.
Page 239: Rear Wiper And Washer
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 Rear Wiper And Washer The sensitivity of the system is adjustable from the multifunction lever. Wiper sensitivity position 3 has been Rotating the rotary ring to the first detent activates the calibrated for best overall wiping sensitivity. If the opera- rear intermittent wipers.
Page 240 238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Rain Sensing feature can be turned on and off • Neutral Wipe Inhibit — The Rain Sensing feature will through the EVIC (if equipped). Refer to “Electronic not operate when the ignition is ON, and the transmis- Vehicle Information Center (EVIC)/Personal Settings sion shift lever is in the NEUTRAL position, and the (Customer-Programmable Features)”...
Page 241: Tilt/Telescoping Steering Column
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 TILT/TELESCOPING STEERING COLUMN To unlock the steering column, push the lever downward (toward the floor). To tilt the steering column, move the This feature allows you to tilt the steering column steering wheel upward or downward as desired. To upward or downward.
Page 242: Heated Steering Wheel - If Equipped
240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE HEATED STEERING WHEEL — IF EQUIPPED The heated steering wheel switch is located on the switch bank below the climate controls. There are also soft-keys The steering wheel contains a heating element that helps in the radio screen that will activate the heated steering warm your hands in cold weather.
Page 243: Adjustable Pedals - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 Vehicles Equipped With Remote Start WARNING! (Continued) On models that are equipped with remote start, the • Do not place anything on the steering wheel that heated steering wheel can be programed to come on insulates against heat, such as a blanket or steering during a remote start.
Page 244 242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the switch rearward to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF. • The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control Sys- tem is on.
Page 245: Electronic Speed Control - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 • For vehicles equipped with Driver Memory Seat, you WARNING! can use your Remote Keyless Entry (RKE) transmitter or the memory switch on the driver’s door trim panel Do not adjust the pedals while the vehicle is moving. to return the adjustable pedals to pre-programmed You could lose control and have an accident.
Page 246: To Activate
244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Elec- tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed.
Page 247: To Set A Desired Speed
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 To Deactivate WARNING! A soft tap on the brake pedal, pushing the CANCEL Leaving the Electronic Speed Control system on button, or normal brake pressure while slowing the when not in use is dangerous. You could accidentally vehicle will deactivate the Electronic Speed Control with- set the system or cause it to go faster than you want.
Page 248 246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the button is continually pressed, the set speed will The speed increment shown is dependant on the speed of U.S. (mph) or Metric (km/h) units: continue to increase until the button is released, then the new set speed will be established.
Page 249: To Accelerate For Passing
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 Metric Speed (km/h) NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on • Pressing the SET (-) button once will result in a 2 km/h moderate hills is normal.
Page 250: Parksense® Rear Park Assist - If Equipped
248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKSENSE® REAR PARK ASSIST — IF speed is increased to approximately 11 mph (18 km/h) or EQUIPPED above. The system will become active again if the vehicle speed is decreased to speeds less than approximately The ParkSense®...
Page 251: Parksense® Warning Display
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249 ParkSense® Warning Display The ParkSense® Warning screen will only be displayed if Sound and Display is selected from the Customer- Programmable Features section of the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer- Programmable Features)”...
Page 252: Parksense® Display
250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense® Display When the vehicle is in REVERSE, the warning display will turn ON indicating the system status. Park Assist System OFF The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the EVIC Park Assist System ON display will show fewer arcs and the sound tone will...
Page 253 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251 Slow Tone Fast Tone...
Page 254 252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: Continuous Tone...
Page 255: Enabling/Disabling Parksense
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253 WARNING ALERTS Rear Distance Greater than 79-39 in 39-25 in 25-12 in Less than (in/cm) 79 in (200 cm) (200-100 cm) (100-65 cm) (65-30 cm) 12 in (30 cm) Audible Alert None Single 1/2 Slow Fast Continuous...
Page 256: Service The Parksense® Rear Park Assist System
254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE shift lever is moved to REVERSE and the system is If “SERVICE PARK ASSIST SYSTEM” appears in the disabled, the EVIC will display the “PARK ASSIST SYS- Electronic Vehicle Information Center (EVIC) after mak- TEM OFF”...
Page 257 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255 • Jackhammers, large trucks, and other vibrations could • Clean the ParkSense® sensors regularly, taking care affect the performance of ParkSense®. not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. •...
Page 258 256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! • ParkSense® is only a parking aid and it is unable to • Drivers must be careful when backing up even recognize every obstacle, including small obstacles. when using ParkSense®. Always check carefully Parking curbs might be temporarily detected or not behind your vehicle, look behind you, and be sure detected at all.
Page 259: Parkview® Rear Back Up Camera - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257 PARKVIEW® REAR BACK UP CAMERA — IF WARNING! (Continued) EQUIPPED • Before using ParkSense®, it is strongly recom- Your vehicle may be equipped with the ParkView® Rear mended that the ball mount and hitch ball assem- Back Up Camera that allows you to see an on-screen bly is disconnected from the vehicle when the image of the rear surroundings of your vehicle whenever...
Page 260 258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When displayed, static grid lines will illustrate the width that will help indicate the distance to the rear of the of the vehicle while a dashed center-line will indicate the vehicle. The following table shows the approximate center of the vehicle to assist with aligning to a hitch/ distances for each zone: receiver.
Page 261: Turning Parkview® On Or Off - With Navigation/Multimedia Radio
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259 3. Press the “camera setup” soft-key. CAUTION! (Continued) 4. Enable or disable the rear camera feature by selecting • To avoid vehicle damage, the vehicle must be the “enable rear camera in reverse” soft-key. driven slowly when using ParkView®...
Page 262: Overhead Consoles
260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLES Front Overhead Console Two versions of the overhead console are available. The base front overhead console model featured fixed incan- descent courtesy/reading lights, flip-down sunglass stor- age and conversation mirror. The premium front over- head console model features a LED focused light that illuminates the instrument panel cupholders, two swiv- eling LED lights, flip-down sunglass storage, conversa-...
Page 263: Courtesy/Interior Lighting
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261 Courtesy/Interior Lighting Sunglass Storage (Non-Sunroof Only) At the forward end of the console are two courtesy lights At the front of the overhead console, a compartment is (standard dome light has two buttons). The lights turn on provided for the storage of two pairs of sunglasses.
Page 264 262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Full Open Position Conversation Mirror Position From this position, the door can be fully closed or, by NOTE: From the “conversation mirror” position, the rotating upward about 3/4 of the way and releasing, door can only be closed.
Page 265: Rear Courtesy/Reading Lights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263 Rear Courtesy/Reading Lights — If Equipped The overhead console has two sets of courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed.
Page 266: Garage Door Opener - If Equipped
264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Console Halo Lighting The rear overhead console has recessed halo lighting around the perimeter of the console base. This feature provides additional lighting options while traveling and is controlled by the headlight switch. Refer to “Lights/ Halo Lights —...
Page 267 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265 HomeLink® Buttons/Overhead Consoles HomeLink® Buttons/Sunvisor/Headliner NOTE: HomeLink® is disabled when the Vehicle Secu- rity Alarm is active.
Page 268: Before You Begin Programming Homelink
266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Before You Begin Programming HomeLink® NOTE: • Erasing all channels should only be performed when Be sure that your vehicle is parked outside of the garage before you begin programming. programming HomeLink® for the first time. Do not erase channels when programming additional buttons.
Page 269 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to pro- gram while keeping the HomeLink® indicator light in view. 3. Simultaneously press and hold both the HomeLink® button you want to program and the hand-held trans- mitter button.
Page 270: Programming A Non-Rolling Code
268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Firmly press and release the “LEARN” or “TRAIN- Reprogramming A Single HomeLink® Button ING” button. On some garage door openers/devices To reprogram a channel that has been previously trained, there may be a light that blinks when the garage door follow these steps: opener/device is in the LEARN/TRAIN mode.
Page 271 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269 • To program the two remaining HomeLink® buttons, 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to pro- repeat each step for each remaining button. DO NOT gram while keeping the HomeLink®...
Page 272: Canadian/Gate Operator Programming
270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Canadian/Gate Operator Programming 3. Continue to press and hold the HomeLink® button, while you press and release (“cycle”), your hand-held For programming transmitters in Canada/United States transmitter every two seconds until HomeLink® has that require the transmitter signals to “time-out”...
Page 273: Using Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271 If you unplugged the garage door opener/device for Using HomeLink® programming, plug it back in at this time. To operate, press and release the programmed HomeLink® button. Activation will now occur for the Reprogramming A Single HomeLink®...
Page 274: Troubleshooting Tips
272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Troubleshooting Tips WARNING! If you are having trouble programming HomeLink®, Vehicle exhaust contains carbon monoxide, a danger- here are some of the most common solutions: ous gas. Do not run your vehicle in the garage while •...
Page 275: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273 NOTE: WARNING! (Continued) • The transmitter has been tested and it complies with use a garage door opener without these safety fea- FCC and IC rules. Changes or modifications not ex- tures. Call toll-free 1–800–355–3515 or, on the Internet pressly approved by the party responsible for compli- at www.HomeLink.com for safety information or ance could void the user’s authority to operate the...
Page 276: Power Sunroof - If Equipped
274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof switch is located between the sun • Never leave children unattended in a vehicle, or visors on the overhead console. with access to an unlocked vehicle. Never leave the Key Fob in or near the vehicle, or in a location accessible to children.
Page 277: Opening Sunroof - Express
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275 movement. The sunroof and sunshade will remain in a WARNING! (Continued) partially opened condition until the switch is pushed and • Do not allow small children to operate the sunroof. held rearward again. Never allow your fingers, other body parts, or any Closing Sunroof —...
Page 278: Pinch Protect Feature
276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Feature Sunshade Operation This feature will detect an obstruction in the opening of The sunshade can be opened manually. However, the the sunroof during Express Close operation. If an ob- sunshade will open automatically as the sunroof opens. struction in the path of the sunroof is detected, the NOTE: The sunshade cannot be closed if the sunroof is sunroof will automatically retract.
Page 279: Sunroof Maintenance
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 277 Sunroof Maintenance ELECTRICAL POWER OUTLETS — IF EQUIPPED Use only a non-abrasive cleaner and a soft cloth to clean Two 12 Volt (13 Amp) power outlets are located on the the glass panel. lower instrument panel, below the open storage bin.
Page 280 278 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. •...
Page 281 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 279 One outlet in the removable floor console (if equipped) On vehicles equipped with the Super Console the power shares a fuse with the lower outlet in the instrument outlets are located under the retractable cover. To access panel and is also connected to the battery.
Page 282 280 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The outlet in the rear quarter panel near the liftgate and the upper outlet in the instrument panel are both con- trolled by the ignition switch. Each of these outlets can support 160 Watts (13 Amps). Do not exceed 160 Watts (13 Amps) for each of these outlets.
Page 283 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 281 WARNING! CAUTION! • Many accessories that can be plugged in draw To avoid serious injury or death: • Only devices designed for use in this type of outlet power from the vehicle’s battery, even when not in should be inserted into any 12 Volt outlet.
Page 284: Power Inverter - If Equipped
282 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • Power outlets are designed for accessory plugs only. Do not hang any type of accessory or acces- sory bracket from the plug. Improper use of the power outlet can cause damage. POWER INVERTER —...
Page 285: Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 283 This outlet can power cellular phones, electronics and WARNING! other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Play- To avoid serious injury or death: • Do not insert any objects into the receptacles. station3 and XBox360 will exceed this power limit, as will •...
Page 286: Instrument Panel Cupholders
284 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Instrument Panel Cupholders variety of container types and sizes. Press down on the container to engage the cupholder retention features. The instrument panel cupholders are located in a pull-out drawer just above the lower storage bin. Super Console —...
Page 287: Premium Console Cupholders - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 285 For rear passengers two cupholders are located in the Premium Console Cupholders — If Equipped pull-out drawer, located in the back of the Super Console. On models equipped with premium center consoles, Pull the drawer out to the first position to use the there are four cupholders located on the top of the cupholders.
Page 288: Interior Bottle Holders
286 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Bottle Holders There are four bottle holders located in the interior. One bottle holder is molded into each front interior door trim panels, and one bottle holder is molded into each side sliding interior door trim panel.
Page 289: Smoker's Package Kit - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 287 Smoker’s Package Kit — If Equipped Upper Glove Compartment With the optional authorized dealer-installed Smoker’s To open the upper compartment, press in on the button, Package Kit, a removable ash receiver is inserted into one located on the left side of the upper door.
Page 290: Door Trim Panel Storage
288 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lower Glove Compartment Door Trim Panel Storage To open the lower compartment pull out on the release Front Door Storage handle. Both interior front door panels have multiple pockets for storage. WARNING! If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burn- ing the occupants.
Page 291: Umbrella Holder
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 289 Umbrella Holder An umbrella holder has been conveniently molded into the left front door entry scuff molding. Driver’s Seatback Storage 1 — Bag Holder 2 — Standard Pocket 3 — Mesh Pocket Umbrella Holder...
Page 292: Second Row Floor Storage Bins
290 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second Row Floor Storage Bins Pull up on the storage bin latch to open the cover. Slide the storage bin locking mechanism to the unlocked The area below the floor covers, located in front of the position to allow greater access to the storage bin.
Page 293: Storage Bin Safety Warning
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 291 WARNING! (Continued) WARNING! (Continued) • Do not operate the storage bin covers while the • In a collision, serious injury could result if the seat vehicle is in motion. storage bin covers are not properly latched. •...
Page 294: Center And Rear Overhead Console Storage - If Equipped
292 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seat Storage Bin Cover Emergency Release Lever NOTE: In the event of an individual being locked inside the storage bin, the storage bin cover can be opened from As a security measure, the Seat Storage Bin Cover has an inside of the bin by pushing on the glow-in-the-dark Emergency Release Lever built into the latching mecha- lever attached to the storage bin cover latching mecha-...
Page 295: Coat Hooks
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 293 Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle.
Page 296: Console Features
294 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES There are three consoles available: Basic, Premium and Super. WARNING! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision.
Page 297 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 295 • The cupholders are removable to access a large storage 2. Slide the console rearward into the floor bracket/ bin. hook. • The basic console is removable from the vehicle for 3. Align the console until the front anchor cup plug hole additional floor space by removing the cap and clip at is centered on the winch hole.
Page 298: Premium Console - If Equipped
296 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • 12 Volt DC power outlet provides continuous power Premium Console — If Equipped inside the console for cell phones or other electronics The three-compartment console with sliding storage bin, • Rear occupant accessible sliding upper tray with storage and large console storage bin offers multiple configurations.
Page 299 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 297 Position 2 shows the raised storage tray revealing a large storage area below. Console Position 1 Console Position 2...
Page 300 298 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dual Storage Bins Position 4 shows the complete console in its rearmost position. Again, lifting second latch handle at the front of Position 3 shows the top portion of the console in a the console, allows complete access to a lower storage bin rearward position.
Page 301: Super Console - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 299 To Remove The Premium Floor Console 4. Push down on the rear of the console until it is seated in the rear floor bracket. 1. Pull up on the bottom release handle in the front of the console.
Page 302 300 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Lower Pass Through Super Console The super console tambour doors are opened by pushing 1 — Front Sliding Tambour Door down on the finger tabs and sliding the door. The front 2 — Cupholder Light Ring tambour door slides forward, the rear tambour door 3 —...
Page 303: Cargo Area Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 301 NOTE: The front cupholder light ring and pass through CARGO AREA FEATURES lighting is controlled by a dimming switch located on the Rechargeable Flashlight instrument panel, refer to “Lights” in “Understanding The rechargeable flashlight is mounted on the right side The Features Of Your Vehicle”...
Page 304 302 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press in on the flashlight to release it. To operate the flashlight, press the switch once for high, twice for low, and a third time to return to off. Press And Release Three-Press Switch...
Page 305: Rear Window Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 303 • To prevent excessive battery drain, use the rear win- REAR WINDOW FEATURES dow defroster only when the engine is operating. Rear Window Defroster CAUTION! The rear window defroster button is located on Failure to follow these cautions can cause damage to the climate control (Mode) knob.
Page 306: Roof Luggage Rack - If Equipped
304 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LOAD LEVELING SYSTEM — IF EQUIPPED vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the The automatic load leveling system will provide a level- maximum vehicle load capacity.
Page 307: Deploying The Crossbars
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 305 not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. NOTE: • Crossbars are error-proofed and cannot be deployed or stowed in the incorrect positions. • To help control wind noise, stow the crossbars in the side rails when they are not in use.
Page 308 306 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Bend the crossbar supports at each end, taking care to keep hand clear of pivoting joint. Slide the thumb screw down. Deployed Position Then, position the crossbars across the roof. NOTE: The crossbars are identical and can be placed in Stowed Position any two of the three deploy positions.
Page 309 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 307 Deploy Positions – Choose Two Of Three Crossbar To Side Rail Installation Make sure the directional arrows on the crossbars align Once the crossbars are set into position, tighten the with the directional arrows on the side rails. Set the thumb screws completely.
Page 310 308 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Stowing The Crossbars Reverse the procedure to stow the crossbars, again, taking care to keep hand clear of pivoting joint. Crossbars are identical and can be stowed in either rail nest. Once the crossbars are stowed, tighten the thumb screws completely.
Page 311 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 309 CAUTION! • Check deployed crossbars frequently and retighten thumb screws as necessary. • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lb (68 kg).
Page 312: Sun Screens - If Equipped
310 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) WARNING! • Long loads which extend over the windshield, such Cargo must be securely tied before driving your as wood panels or surfboards, or loads with large vehicle. Improperly secured loads can fly off the frontal area should be secured to both the front and vehicle, particularly at high speeds, resulting in per- rear of the vehicle.
Page 313 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 311 Sun Screen Retracted Sun Screen Extended Gently pull up on the tab to raise the sun screen. To lower the sun screen, gently lift the tab upward to Continue pulling the sun screen until the tab is near the disengage the hooks, and feed the screen back into the top of the window.
Page 315 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS ▫ EVIC Red Telltale Lights ....342 INSTRUMENT PANEL FEATURES ..318 ▫ Oil Change Required ....345 INSTRUMENT CLUSTER —...
Page 316 314 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Units ......349 Uconnect® 130 ......361 ▫...
Page 317 UNDERSTANDING YOUR INSTRUMENT PANEL 315 ▫ Operating Instructions (Uconnect® Phone) — If ▫ Getting Started ..... . .395 Equipped ......386 ▫...
Page 318 316 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ VES™ Remote Control — If Equipped ..412 ▫ Information Mode Display ....424 ▫ Blu-ray™ Player Remote Control — If ▫...
Page 319 UNDERSTANDING YOUR INSTRUMENT PANEL 317 ▫ Summer Operation ....461 CD/DVD/Blu-ray™ Disc MAINTENANCE ..442 ▫ Winter Operation..... .461 RADIO OPERATION AND MOBILE PHONES .
Page 320: Instrument Panel Features
318 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 — Air Vents 5 — Analog Clock 9 — DVD – If Equipped 13 — Ignition Switch 2 — Instrument Cluster 6 — Upper Glove Compartment 10 — Storage Bin 14 — Hood Release 3 —...
Page 321: Instrument Cluster - Base
UNDERSTANDING YOUR INSTRUMENT PANEL 319 INSTRUMENT CLUSTER — BASE...
Page 322: Instrument Cluster - Premium
320 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — PREMIUM...
Page 323: Instrument Cluster Descriptions
UNDERSTANDING YOUR INSTRUMENT PANEL 321 INSTRUMENT CLUSTER DESCRIPTIONS 4. Turn Signal Indicators 1. Tachometer The arrow will flash with the exterior turn signal when the turn signal lever is operated. This gauge measures engine revolutions per minute (RPM x 1000). Before the pointer reaches the red area, If the vehicle is driven more than 1 mile (1.6 km) ease up on the accelerator to prevent engine damage.
Page 324 322 UNDERSTANDING YOUR INSTRUMENT PANEL U.S. Federal regulations require that upon transfer of Message Display Area vehicle ownership, the seller certify to the purchaser the When the appropriate conditions exist, the following correct mileage that the vehicle has been driven. If your odometer messages will display: odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same...
Page 325 UNDERSTANDING YOUR INSTRUMENT PANEL 323 NOTE: Some of the above warnings will be displayed in noFUSE the Electronic Vehicle Information Center Display Area If the vehicle diagnostic system determines that the located in the instrument cluster. Ignition Off Draw (IOD) fuse is improperly installed, or Refer to ”Electronic Vehicle Information Center (EVIC) damaged, a “noFUSE”...
Page 326 324 UNDERSTANDING YOUR INSTRUMENT PANEL position. To turn off the message temporarily, press and instrument cluster. For further information, refer to release the STEP button on the steering wheel. To reset “Electronic Vehicle Information Center (EVIC)”. the oil change indicator system (after performing the 7.
Page 327 UNDERSTANDING YOUR INSTRUMENT PANEL 325 8. Tire Pressure Monitoring Telltale Light — If Equipped reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Each tire, including the spare (if provided), Please note that the TPMS is not a substitute for proper should be checked monthly when cold and tire maintenance, and it is the driver’s responsibility to inflated to the inflation pressure recommended...
Page 328 326 UNDERSTANDING YOUR INSTRUMENT PANEL of reasons, including the installation of replacement or CAUTION! (Continued) alternate tires or wheels on the vehicle that prevent the balance beads if your vehicle is equipped with a TPMS from functioning properly. Always check the TPMS, as damage to the sensors may result.
Page 329 UNDERSTANDING YOUR INSTRUMENT PANEL 327 10. Electronic Stability Control (ESC) Activation/ CAUTION! Malfunction Indicator Light — If Equipped Prolonged driving with the Malfunction Indicator The “ESC Activation/Malfunction Indicator Light (MIL) on could cause damage to the engine Light” in the instrument cluster will come on control system.
Page 330 328 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: 11. Electronic Stability Control (ESC) OFF Indicator Light — If Equipped • The “ESC Off Indicator Light” and the “ESC Activation/Malfunction Indicator Light” come on This light indicates the Electronic Stability Con- momentarily each time the ignition switch is turned trol (ESC) is off.
Page 331 UNDERSTANDING YOUR INSTRUMENT PANEL 329 15. Air Bag Warning Light NOTE: • You must apply the brakes before shifting from This light will turn on for four to eight seconds PARK. as a bulb check when the ignition switch is first turned to ON/RUN.
Page 332 330 UNDERSTANDING YOUR INSTRUMENT PANEL 18. Brake Warning Light The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic This light monitors various brake functions, system. A leak in either half of the dual brake system is including brake fluid level and parking brake indicated by the Brake Warning Light, which will turn on application.
Page 333 UNDERSTANDING YOUR INSTRUMENT PANEL 331 The light also will turn on when the parking brake is WARNING! applied with the ignition switch in the ON/RUN posi- tion. Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. NOTE: This light shows only that the parking brake is It will take longer to stop the vehicle.
Page 334 332 UNDERSTANDING YOUR INSTRUMENT PANEL 20. Temperature Gauge WARNING! The temperature gauge shows engine coolant tempera- A hot engine cooling system is dangerous. You or ture. Any reading within the normal range indicates that others could be badly burned by steam or boiling the engine cooling system is operating satisfactorily.
Page 335 UNDERSTANDING YOUR INSTRUMENT PANEL 333 22. Charging System Light Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine. This light shows the status of the electrical charging The engine oil level must be checked under the hood.
Page 336 334 UNDERSTANDING YOUR INSTRUMENT PANEL 25. Electronic Throttle Control (ETC) Light 26. Transmission Temperature Warning Light This light informs you of a problem with the During sustained high speed driving or trailer Electronic Throttle Control (ETC) system. The towing up long grades on hot days, the auto- light will come on when the ignition is first matic transmission oil may become too hot.
Page 337: Electronic Vehicle Information Center (Evic) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 335 CAUTION! Continuous driving with the Transmission Tempera- ture Warning Light illuminated will eventually cause severe transmission damage or transmission failure. WARNING! If you continue operating the vehicle when the Transmission Temperature Warning Light is illumi- nated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and Electronic Vehicle Information Center (EVIC)
Page 338 336 UNDERSTANDING YOUR INSTRUMENT PANEL • Fuel Economy • Vehicle Speed • Trip Info • Tire PSI • Vehicle Info • Messages • Units • System Setup (Personal Settings) • Turn Menu Off EVIC Steering Wheel Buttons UP Button The system allows the driver to select information by pressing the following buttons mounted on the steering Press and release the UP button to scroll up- wheel:...
Page 339: Electronic Vehicle Information Center (Evic) Displays
UNDERSTANDING YOUR INSTRUMENT PANEL 337 DOWN Button Electronic Vehicle Information Center (EVIC) Displays Press and release the DOWN button to scroll The EVIC display consists of three sections: downward through the main menus and sub-menus. 1. The top line where compass direction and outside temperature are displayed.
Page 340 338 UNDERSTANDING YOUR INSTRUMENT PANEL • Unstored Messages The main display area will normally display the main menu or the screens of a selected feature of the main This message type is displayed indefinitely or until the menu. The main display area also displays pop up condition that activated the message is cleared.
Page 341 UNDERSTANDING YOUR INSTRUMENT PANEL 339 The Reconfigurable Telltales section is divided into the Wrong Key white telltales area on the right, amber telltales in the Damaged Key middle, and red telltales on the left. Key not programmed When the appropriate conditions exist, the EVIC displays the following messages: Vehicle Not in Park Key in ignition...
Page 342 340 UNDERSTANDING YOUR INSTRUMENT PANEL RKE Battery Low Blind Spot System Off — This message is displayed when the ignition is turned to ON to indicate the Blind Spot Service Keyless System System has been turned off. Low Washer Fluid Blind Spot System Not Available —...
Page 343: Evic White Telltale Lights
UNDERSTANDING YOUR INSTRUMENT PANEL 341 • Electronic Speed Control SET EVIC White Telltale Lights This area will show reconfigurable white caution tell- This light will turn on when the electronic tales. These telltales include: speed control is SET. For further information, refer to “Electronic Speed Control”...
Page 344: Evic Red Telltale Lights
342 UNDERSTANDING YOUR INSTRUMENT PANEL • Loose Gascap Indicator EVIC Red Telltale Lights This area will show reconfigurable red telltales. These If the vehicle diagnostic system determines telltales include: that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap indicator •...
Page 345 UNDERSTANDING YOUR INSTRUMENT PANEL 343 • Charging System Light turned ON and remain on briefly as a bulb check. If the light does not come on during starting, have the system This light shows the status of the electrical charg- checked by an authorized dealer.
Page 346 344 UNDERSTANDING YOUR INSTRUMENT PANEL • Engine Temperature Warning Light • Transmission Temperature Warning Light This light warns of an overheated engine condi- This light indicates that the transmission fluid tion. As temperatures rise and the gauge ap- temperature is running hot. This may occur proaches H, this indicator will illuminate and a single with severe usage, such as trailer towing.
Page 347: Oil Change Required
UNDERSTANDING YOUR INSTRUMENT PANEL 345 Unless reset, this message will continue to display each WARNING! time you turn the ignition switch to the ON/RUN position or cycle the ignition to the ON/RUN position if If you continue operating the vehicle when the equipped with Keyless Enter-N-Go™.
Page 348: Fuel Economy
346 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Without pressing the brake pedal, push the ENGINE Fuel Economy START/STOP button once to return the ignition to the Press and release the UP or DOWN button until “Fuel OFF/LOCK position. Economy” displays highlighted in the EVIC and press Vehicles Not Equipped With Keyless Enter-N-Go™...
Page 349 UNDERSTANDING YOUR INSTRUMENT PANEL 347 NOTE: Significant changes in driving style or vehicle loading will greatly affect the actual drivable distance of the vehicle, regardless of the DTE displayed value. When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a “LOW FUEL”...
Page 350: Vehicle Speed
348 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicle Speed Trip A Press and release the UP or DOWN button until “Vehicle Shows the total distance traveled for Trip A since the last Speed” displays highlighted in the EVIC and press the reset. SELECT button.
Page 351: Tire Psi
UNDERSTANDING YOUR INSTRUMENT PANEL 349 Tire PSI Vehicle Info (Customer Information Features) Press and release the UP or DOWN button until “Tire Press and release the UP or DOWN button until “Vehicle PSI:” displays highlighted in the EVIC. Press the SELECT Info”...
Page 352: Messages
350 UNDERSTANDING YOUR INSTRUMENT PANEL • Trailer Brake — If Equipped Keyless Enter-N-Go™ Display — If Equipped When the ENGINE START/STOP button is pressed to Displays trailer brake output power and trailer brake change ignition switch position, current ignition status status indicator.
Page 353 UNDERSTANDING YOUR INSTRUMENT PANEL 351 Automatic Compass Calibration 2. Press the UP or DOWN button until the System Setup (Customer-Programmable Features) menu is reached, This compass is self-calibrating, which eliminates the then press the SELECT button. need to manually reset the compass. When the vehicle is new, the compass may appear erratic until it is calibrated.
Page 354 352 UNDERSTANDING YOUR INSTRUMENT PANEL the vehicle is driven, per the zone map. Once properly set, the compass will automatically compensate for the differences, and provide the most accurate compass heading. For the most accurate compass performance, the compass must be set using the following steps. NOTE: Keep magnetic materials away from the top of the instrument panel, such as iPod’s, Mobile Phones, Laptops and Radar Detectors.
Page 355: Compass Variance
UNDERSTANDING YOUR INSTRUMENT PANEL 353 3. Press the DOWN button until the “Compass Variance” Press and release the UP or DOWN button until System message is displayed in the EVIC, then press the Setup is highlighted in the main menu of the EVIC. Then SELECT button.
Page 356 354 UNDERSTANDING YOUR INSTRUMENT PANEL route mile by mile, turn-by-turn until the final destina- Refer to “Rear Park Assist System” in “Understanding tion is reached. To make your selection, press and release The Features Of Your Vehicle” for system function and the SELECT button until a check-mark appears next to operating information.
Page 357 UNDERSTANDING YOUR INSTRUMENT PANEL 355 transmitter UNLOCK button twice, to unlock the passen- Remote Start Comfort Sys. ger’s doors. When All Doors 1st Press is selected, all of When this feature is selected and the remote start is the doors will unlock on the first press of the RKE activated, the heated steering wheel and driver heated transmitter UNLOCK button.
Page 358 356 UNDERSTANDING YOUR INSTRUMENT PANEL Horn With Remote Start Automatic High Beams — If Equipped When this feature is selected, a short horn sound will When this feature is selected, the high beam headlights occur when the RKE transmitter REMOTE START button will deactivate automatically under certain conditions.
Page 359 UNDERSTANDING YOUR INSTRUMENT PANEL 357 Headlamps With Wipers (Available With Auto the SELECT button until a check-mark appears next to Headlights Only) the feature showing the system has been activated or the check-mark is removed showing the system has been When ON is selected, and the headlight switch is in the deactivated.
Page 360 358 UNDERSTANDING YOUR INSTRUMENT PANEL Illuminated Approach Flashers With Sliding Door When this feature is selected, the headlights will activate When this feature is selected the signal lamps activate and remain on for up to 90 seconds when the doors are when power or manual sliding doors are in operation, unlocked with the RKE transmitter.
Page 361 UNDERSTANDING YOUR INSTRUMENT PANEL 359 Easy Exit Seat To make your selection, press and release the SELECT button until a check-mark appears next to the feature This feature provides automatic driver seat positioning to showing the system has been activated or the check-mark enhance driver mobility when entering and exiting the is removed showing the system has been deactivated.
Page 362: Uconnect® 730N/430/430N Cd/Dvd/Hdd/Nav
360 UNDERSTANDING YOUR INSTRUMENT PANEL To make your selection, press and release the SELECT Daytime Running Lights — If Equipped button until a check-mark appears next to the feature When selected, the headlights on your vehicle will illu- showing the system has been activated or the check-mark minate when the engine is started and the transmission is is removed showing the system has been deactivated.
Page 363: Operating Instructions (Uconnect® Phone) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 361 Operating Instructions (Uconnect® Phone) — If Operating Instructions — Radio Mode Equipped NOTE: The ignition switch must be in the ON or ACC Refer to “Uconnect® Phone” for further details. position to operate the radio. Power Switch/Volume Control (Rotary) Uconnect®...
Page 364 362 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes Press and release the SEEK buttons to search for the next will begin to blink. listenable station in AM/FM mode.
Page 365 UNDERSTANDING YOUR INSTRUMENT PANEL 363 Setting The Tone, Balance And Fade Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control Push the rotary TUNE/SCROLL control knob and BASS knob to the left or right to adjust the sound level between will display.
Page 366: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
364 UNDERSTANDING YOUR INSTRUMENT PANEL SET/RND button, the station will continue to play but DISC Button will not be stored into pushbutton memory. Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes. You may add a second station to each pushbutton by repeating the above procedure with this exception: Press Operation Instructions —...
Page 367 UNDERSTANDING YOUR INSTRUMENT PANEL 365 radio display. If a CD does not go into the slot more than CAUTION! (Continued) 1.0 in (2.5 cm), a disc may already be loaded and must be • The Uconnect® 130 is a single CD player. Do not ejected before a new disc can be loaded.
Page 368 366 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Ejecting with the ignition OFF is not allowed on RW/FF convertible or soft-top models (if equipped). Press and hold the FF (Fast Forward) button and the CD player will begin to fast forward until FF is released, or SEEK Button RW or another CD button is pressed.
Page 369: Notes On Playing Mp3 Files
UNDERSTANDING YOUR INSTRUMENT PANEL 367 Notes On Playing MP3 Files The radio uses the following limits for file systems: • Maximum number of folder levels: 8 The radio can play MP3 files; however, acceptable MP3 file recording media and formats are limited. When •...
Page 370 368 UNDERSTANDING YOUR INSTRUMENT PANEL Multisession disc formats are supported by the radio. Mul- MPEG Specifi- Sampling Fre- Bit Rate (kbps) tisession discs may contain combinations of normal CD cation quency (kHz) audio tracks and computer files (including MP3 files). Discs MPEG-1 Audio 48, 44.1, 32 320, 256, 224,...
Page 371: Operation Instructions - Auxiliary Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 369 Playback Of MP3 Files Operation Instructions — Auxiliary Mode When a medium containing MP3 data is loaded, the The auxiliary (AUX) jack is an audio input jack, which radio checks all files on the medium. If the medium allows the user to plug in a portable device, such as an contains a lot of folders or files, the radio will take more MP3 player, or iPod®, and utilize the vehicle’s audio...
Page 372: Uconnect® 130 With Satellite Radio
370 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect® 130 WITH SATELLITE RADIO Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction, without stopping.
Page 373 UNDERSTANDING YOUR INSTRUMENT PANEL 371 another selection. Holding either button will bypass Phone Button Uconnect® Phone — If Equipped stations without stopping, until you release it. Press this button to operate the Uconnect® Phone feature (if equipped). Refer to “Uconnect® Phone” for further Voice Command System (Radio) —...
Page 374 372 UNDERSTANDING YOUR INSTRUMENT PANEL 3. After adjusting the hours, press the right side TUNE/ INFO Button SCROLL control knob to set the minutes. The minutes Press the INFO button for an RDS station (one with call will begin to blink. letters displayed).
Page 375 UNDERSTANDING YOUR INSTRUMENT PANEL 373 Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the MUSIC TYPE Button mid-range tones.
Page 376 374 UNDERSTANDING YOUR INSTRUMENT PANEL 16-Digit Character Dis- 16-Digit Character Dis- Program Type Program Type play play Classical Classicl Religious Talk Rel Talk Classic Rock Cls Rock Rock Rock College College Soft Soft Country Country Soft Rock Soft Rck Foreign Language Language Soft Rhythm and Blues Soft R&B...
Page 377 UNDERSTANDING YOUR INSTRUMENT PANEL 375 If a preset button is activated while in the Music Type SET/RND Button — To Set The Pushbutton (Program Type) mode, the Music Type mode will be Memory exited and the radio will tune to the preset station. When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND SETUP Button...
Page 378: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
376 UNDERSTANDING YOUR INSTRUMENT PANEL • This radio is capable of playing compact discs (CD), Every time a preset button is used, a corresponding button number will display. recordable compact discs (CD-R), rewritable compact discs (CD-RW), compact discs with MP3 tracks and Buttons 1 - 6 multisession compact discs with CD and MP3 tracks.
Page 379 UNDERSTANDING YOUR INSTRUMENT PANEL 377 EJECT Button — Ejecting A CD CAUTION! • This CD player will accept 4–3/4 in (12 cm) discs Press the EJECT button to eject the CD. only. The use of other sized discs may damage the CD player mechanism.
Page 380: Notes On Playing Mp3 Files
378 UNDERSTANDING YOUR INSTRUMENT PANEL the current selection. Pressing and holding the SEEK SET/RND Button (Random Play Button) button will allow faster scrolling through the tracks in Press this button while the CD is playing to activate CD and MP3 modes. Random Play.
Page 381 UNDERSTANDING YOUR INSTRUMENT PANEL 379 Supported Media (Disc Types) display the file name and folder name, and will assign a number instead. With a maximum number of files, The MP3 file recording media supported by the radio are exceeding 20 folders will result in this display. With CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
Page 382 380 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats MPEG Specifi- Sampling Fre- Bit Rate (kbps) cation quency (kHz) The radio will recognize only files with the *.MP3 exten- sion as MP3 files. Non-MP3 files named with the *.MP3 MPEG-1 Audio 48, 44.1, 32 320, 256, 224, extension may cause playback problems.
Page 383: List Button - Cd Mode For Mp3 Play
UNDERSTANDING YOUR INSTRUMENT PANEL 381 Playback Of MP3 Files LIST Button — CD Mode For MP3 Play When a medium containing MP3 data is loaded, the Pressing the LIST button will bring up a list of all folders radio checks all files on the medium. If the medium on the disc.
Page 384: Uconnect® (Satellite Radio) - If Equipped
382 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds TIME Button (Auxiliary Mode) to return to elapsed time display. Press this button to change the display to time of day. The time of day will display for five seconds (when the Operation Instructions —...
Page 385 UNDERSTANDING YOUR INSTRUMENT PANEL 383 radio system in your vehicle. Sirius will supply a wel- ESN/SID Access come kit that contains general information, including With the ignition switch in the ON/RUN or ACC posi- how to setup your on-line listening account. For further tion and the radio on, press the SETUP button and scroll information, call the toll-free number 888-539-7474, or using the TUNE/SCROLL control knob until Sirius ID is...
Page 386 384 UNDERSTANDING YOUR INSTRUMENT PANEL bikes should be placed as far rearward as possible, within Operating Instructions — Uconnect® (Satellite) the loading design of the rack. Do not place items directly Mode on or above the antenna. NOTE: The ignition switch must be in the ON/RUN or Reception Quality ACC position to operate the radio.
Page 387 UNDERSTANDING YOUR INSTRUMENT PANEL 385 INFO Button MUSIC TYPE Button Pressing the INFO button will cycle the display informa- Pressing this button once will turn on the Music Type tion between Artist, Song Title, and Composer (if avail- mode for five seconds. Pressing the MUSIC TYPE button able).
Page 388: Operating Instructions (Uconnect® Phone) - If Equipped
386 UNDERSTANDING YOUR INSTRUMENT PANEL SETUP Button You may add a second channel to each pushbutton by repeating the above procedure with this exception: Press Pressing the SETUP button allows you to select the the SET button twice and SET 2 will show in the display following items: window.
Page 389: Setting The Analog Clock
UNDERSTANDING YOUR INSTRUMENT PANEL 387 SETTING THE ANALOG CLOCK iPod®/USB/MP3 CONTROL — IF EQUIPPED To set the analog clock at the top center of the instrument NOTE: This section is for Uconnect® 130/230 radios panel, press and hold the button until the setting is only.
Page 390: Connecting The Ipod® Or External Usb Device
388 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • If the radio has a USB port, refer to the appropriate Uconnect® Multimedia radio User’s Manual for iPod® or external USB device support capability. • Connecting an iPod® or consumer electronic audio device to the AUX port located in the radio faceplate, plays media, but does not use the iPod®...
Page 391: Using This Feature
UNDERSTANDING YOUR INSTRUMENT PANEL 389 NOTE: The glove compartment will have a position Using This Feature where the iPod® or consumer electronic audio device By using an iPod® cable, or an external USB device to cable can be routed through without damaging the cable connect to the USB port: when closing the lid.
Page 392: Play Mode
390 UNDERSTANDING YOUR INSTRUMENT PANEL • Jump backward in the current track by pressing and MP3 control mode, audio tracks (if available from audio device) start playing over the vehicle’s audio system. holding the << RW button. Holding the << RW button long enough will jump to the beginning of the current Play Mode track.
Page 393: List Or Browse Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 391 to the next screen of data for that track. Once all device, or press the VR button and say Shuffle ON or screens have been viewed, the last INFO button press Shuffle Off. If the RND icon is showing on the radio will go back to the play mode screen on the radio.
Page 394 392 UNDERSTANDING YOUR INSTRUMENT PANEL • Preset 6 – Podcasts through the list faster. During fast scroll, a slight delay in updating the information on the radio display may • Pressing a PRESET button will display the current list be noticeable. on the top line and the first item in that list on the •...
Page 395: Bluetooth® Streaming Audio (Btsa)
UNDERSTANDING YOUR INSTRUMENT PANEL 393 Bluetooth® Streaming Audio (BTSA) CAUTION! Music can be streamed from your cellular phone to the • Leaving the iPod® or external USB device (or any Uconnect® phone system. supported device) anywhere in the vehicle in ex- Controlling BTSA Using Radio Buttons treme heat or cold can alter the operation or dam- age the device.
Page 396: Entertainment System (Ves™) - If Equipped
394 UNDERSTANDING YOUR INSTRUMENT PANEL Selecting A Different Audio Device Browse Browsing is not available on a Bluetooth® Streaming 1. Press the PHONE button to begin. Audio (BTSA) device. Only the current song that is 2. After the Ready prompt and following the beep, say playing will display info.
Page 397: Getting Started
UNDERSTANDING YOUR INSTRUMENT PANEL 395 • Cycle the ignition to the ON or ACC position. Getting Started • Screen(s) located in the overhead console: Unfold the • Your vehicle may be equipped with either a standard overhead LCD screen(s) by pushing the button on the DVD player or a Blu-ray™...
Page 398: Blu-Ray™ Disc Player
396 UNDERSTANDING YOUR INSTRUMENT PANEL • For Dual Video Screen System, Channel 1 on the playback does not begin automatically after the disc is Remote Control and Headphones refers to Screen 1 inserted into the Blu-ray™ Player press the play button. (second row) and Channel 2 on the Remote Control If playback does not begin automatically after the disc is and Headphones refers to Screen 2 (third row).
Page 399: Play Video Games
UNDERSTANDING YOUR INSTRUMENT PANEL 397 Using The Remote Control • Select an audio channel (Channel 1 for 2nd row screen and Channel 2 for 3rd row screen), then press the source key and select VES™ Disc from the menu. • Press popup/menu key to navigate disc menu and options.
Page 400 398 UNDERSTANDING YOUR INSTRUMENT PANEL When connecting an external source to the AUX input, be sure to follow the standard color coding for the VES™ jacks: NOTE: Certain high-end video games, such as Playsta- tion3 and XBox360 will exceed the power limit of the vehicle’s Power Inverter.
Page 401: Listen To An Audio Source On Channel 2 While A
UNDERSTANDING YOUR INSTRUMENT PANEL 399 Rear VES™ Soft-key Select Channel/Screen 1 And AUX 1 In The VES™ Column 3. Touch the 1 soft-key and then touch either AUX 1 or Listen To An Audio Source On Channel 2 While A AUX 2 in the VES™...
Page 402 400 UNDERSTANDING YOUR INSTRUMENT PANEL Using The Remote Control 1. Press the SOURCE button on the Remote Control and the Mode Select Screen will display, unless a video is playing then only a small banner will appear on the bottom of the screen. 2.
Page 403 UNDERSTANDING YOUR INSTRUMENT PANEL 401 Using The Touchscreen Radio Controls 3. To listen to an audio source on Channel 2 while a video is playing on Channel 1, touch the 2 soft-key and 1. Press the MENU hard-key on the radio faceplate. choose an audio source.
Page 404: Dual Video Screen
402 UNDERSTANDING YOUR INSTRUMENT PANEL Dual Video Screen 2. Insert the DVD with the label facing up. The radio automatically selects the appropriate mode after the NOTE: Typically there are two different ways to operate disc is recognized and displays the menu screen or the features of the Video Entertainment System (VES™).
Page 405 UNDERSTANDING YOUR INSTRUMENT PANEL 403 Using The Remote Control NOTE: • Channel/Screen 1 select mode information is shown 1. Press the SOURCE button on the Remote Control. on the left side of the screen. 2. While looking at Screen 1 or 2, highlight DISC by either •...
Page 406 404 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • To view a DVD on the radio press the RADIO/MEDIA hard-key, on the radio faceplate, then touch the DISC tab soft-key and then the VIEW VIDEO soft-key. • Viewing a DVD on the Touchscreen radio screen is not available in all states/provinces.
Page 407: Play A Dvd Using The Ves™ Player - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 405 Play A DVD Using The VES™ Player — If Using The Remote Control Equipped 1. Press the SOURCE button on the Remote Control. 1. Insert the DVD with the label facing up. The VES™ 2. While looking at Screen 1 or 2, highlight VES™ DISC player automatically selects the appropriate mode by either pressing Up/Down/Left/Right buttons or after the disc is recognized and starts playing the...
Page 408 406 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • Channel/Screen 1 select mode information is shown on the left side of the screen. • Channel/Screen 2 select mode information is shown on the right side of the screen. • The VES™ will retain the last setting when turned off. Using The Touchscreen Radio Controls 1.
Page 409: Play A Blu-Ray™ Disc Using The Blu-Ray™ Player - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 407 • Viewing a DVD on the Touchscreen radio screen is not available in all states/provinces. If available, the ve- hicle must be stopped and the shift lever must be in the PARK position for vehicles with an automatic trans- mission.
Page 410 408 UNDERSTANDING YOUR INSTRUMENT PANEL 3. To watch a Blu-ray™ Disc on Screen 2 for third row Using The Touchscreen Radio Controls passengers, ensure the Remote Control and Head- 1. Press the MENU hard-key on the radio faceplate. phone switch is on Channel 2. 2.
Page 411: Listen To An Audio Source While A Video Is Playing
UNDERSTANDING YOUR INSTRUMENT PANEL 409 • Viewing a Blu-ray™ Disc on the Touchscreen radio 2. While looking at the video screen, either press Up/ screen is not available in all states/provinces. If avail- Down/Left/Right on the Remote Control to highlight able, the vehicle must be stopped and the shift lever the desired audio source or repeatedly press the must be in the PARK position for vehicles with an...
Page 412 410 UNDERSTANDING YOUR INSTRUMENT PANEL Using The Touchscreen Radio Controls 3. To listen to an audio source on Channel 2 while a video is playing on Channel 1, touch the 2 soft-key and 1. Press the MENU hard-key on the radio faceplate. choose an audio source.
Page 413: Important Notes For Dual Video Screen System
UNDERSTANDING YOUR INSTRUMENT PANEL 411 • Selecting a video source on Channel 2, the video Important Notes For Dual Video Screen System source will display on the third row screen or Screen 2 • VES™ is able to transmit two channels of stereo audio and can be heard on Channel 2.
Page 414 412 UNDERSTANDING YOUR INSTRUMENT PANEL VES™ Remote Control — If Equipped audio while the screen is closed, press the Power button to turn the headphone transmitter on. 2. Channel Selector Indicators – When a button is pressed, the currently affected channel or channel button is illuminated momentarily.
Page 415 UNDERSTANDING YOUR INSTRUMENT PANEL 413 – In radio modes, press to seek the next tunable 10. PROG Up/Down / Rewind/skip back and fast fwd/ station. In disc modes, press and hold to fast forward skip forward – When listening to a radio mode, through the current audio track or video chapter.
Page 416 414 UNDERSTANDING YOUR INSTRUMENT PANEL 14. MODE/SOURCE – Press to change the mode of the – In radio modes, press to seek to the previous selected channel. See the Mode Selection section of tunable station. In disc modes, press and hold to fast this manual for details on changing modes.
Page 417: Blu-Ray™ Player Remote Control - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 415 Blu-ray™ Player Remote Control — If Equipped audio while the screen is closed, press the Power button to turn the headphone transmitter on. 2. Channel Selector Indicators – When a button is pressed, the currently affected channel or channel button is illuminated momentarily.
Page 418 416 UNDERSTANDING YOUR INSTRUMENT PANEL 6. SETUP – Press to access the Blu-ray™ Setup menu 11. KEYPAD – Press to navigate chapters or titles. screen. When a disc is loaded in the Blu-ray™ player 12. ▪ (Stop) – Stops disc play. (if equipped) and the VES™...
Page 419: Remote Control Storage
UNDERSTANDING YOUR INSTRUMENT PANEL 417 Remote Control Storage The video screen(s) come with a built in storage compart- ment for the remote control which is accessible when the screen is opened. To remove the remote, use your index finger to pull and rotate the remote towards you. Do not try to pull the remote straight down as it will be very difficult to remove.
Page 420: Replacing The Remote Control Batteries
418 UNDERSTANDING YOUR INSTRUMENT PANEL player (if equipped). If the vehicle is not equipped Headphones Operation with a DVD player, follow the radio’s instructions to The headphones receive two separate channels of audio turn Video Lock on. The radio and the video screen(s) using an infrared transmitter from the video screen.
Page 421: Blu-Ray™ Headphones Operation
UNDERSTANDING YOUR INSTRUMENT PANEL 419 Blu-ray™ Headphones Operation The headphones receive two separate channels of audio using an infrared transmitter from the video screen. Front seat occupants receive some headphone audio coverage to allow them to adjust the headphone volume for the young rear seat occupants that may not be able to do so for themselves.
Page 422: Controls
420 UNDERSTANDING YOUR INSTRUMENT PANEL Controls The headphone power indicator and controls are located on the right ear cup. NOTE: The rear video system must be turned on before sound can be heard from the headphones. To conserve battery life, the headphones will automatically turn off approximately three minutes after the rear video system is turned off.
Page 423: Replacing The Headphone Batteries
UNDERSTANDING YOUR INSTRUMENT PANEL 421 NOTE: 4. When the Mode Selection menu appears on screen, use the cursor buttons on the remote control to navi- • When both switches are on Channel 1, the Remote is gate to the available modes and press the OK button to controlling Channel 1 and the headphones are tuned select the new mode.
Page 424: Unwired® Stereo Headphone Lifetime Limited
422 UNDERSTANDING YOUR INSTRUMENT PANEL Unwired® Stereo Headphone Lifetime Limited What Does This Warranty Not Cover? This warranty Warranty does not cover any damage or defect that results from misuse, abuse or modification of the Product other than Who Does This Warranty Cover? This warranty covers by Unwired.
Page 425: System Information
UNDERSTANDING YOUR INSTRUMENT PANEL 423 What Will Unwired® Do? Unwired®, at its option, will System Information repair or replace any defective Product. Unwired® re- Shared Modes serves the right to replace any discontinued Product with This allows the VES™ to output radio sources to the a comparable model.
Page 426: Information Mode Display
424 UNDERSTANDING YOUR INSTRUMENT PANEL The VES™ has the ability to switch tuner (AM/FM), Information Mode Display SEEK, SCAN, TUNE, and recall presets in radio modes as long as it is not in shared mode. When in shared disc mode both the radio and the VES™ have control of the video functions.
Page 427: Numeric Keypad Menu
UNDERSTANDING YOUR INSTRUMENT PANEL 425 4. Channel 2 Mode Numeric Keypad Menu 5. Channel 2 Shared Status 6. Channel 2 Audio Only/Mute 7. Channel 1 ENTER/OK Button Action 8. Channel 2 ENTER/OK Button Action 9. Clock 10. Video Lock 11. Not Available / Error Numeric Keypad Menu When the display for either Channel 1 or Channel 2 shows DIRECT TUNE, pressing the remote control’s OK...
Page 428: Station List Menu
426 UNDERSTANDING YOUR INSTRUMENT PANEL makes it easy to enter a specific tuner frequency, satellite Station List Menu channel, or track number. To enter the desired digit: When listening to Satellite audio, pressing the remote control’s POP UP/MENU button displays a list of all 1.
Page 429: Disc Menu
UNDERSTANDING YOUR INSTRUMENT PANEL 427 Disc Menu Display Settings When watching a video source (DVD Video with the disc in Play mode, Aux Video, etc.), pressing the remote control’s SETUP button activates the Display Settings menu. These settings control the appearance of the video on the screen.
Page 430: Listening To Audio With The Screen Closed
428 UNDERSTANDING YOUR INSTRUMENT PANEL Listening To Audio With The Screen Closed Disc Formats To listen to only audio portion of the channel with the The DVD player is capable of playing the following types screen closed: of discs (12 cm or 8 cm diameter): •...
Page 431 UNDERSTANDING YOUR INSTRUMENT PANEL 429 • CD: CD-DA, VCD, CD-TEXT • Other compression formats such as Xvid and RMP4 will not play. The Blu-Ray™ Player will automatically • DVD/CD: MP3, WMA, AAC, DivX (versions 3 – 6) skip the file and begin playing the next available file. profile 3.0 •...
Page 432 430 UNDERSTANDING YOUR INSTRUMENT PANEL DVD/Blu-ray™/BD Region Codes Recorded Discs The DVD player/Blu-ray™ Player and many DVD/Blu- The DVD player will play CD-R and CD-RW discs ray™ Discs are coded by geographic region. These region recorded in CD-Audio or Video-CD format, or as a codes must match in order for the disc to play.
Page 433 UNDERSTANDING YOUR INSTRUMENT PANEL 431 • For multi-session CDs that contain only multiple CD- If you are still having trouble writing a disc that is Audio sessions, the player will renumber the tracks so playable in the DVD player, check with the disc recording each track number is unique.
Page 434 432 UNDERSTANDING YOUR INSTRUMENT PANEL • If you are creating your own files, the recommended .WMA. AAC files must always end with the exten- sion aac or AAC. To prevent incorrect playback, do fixed bit rate for MP3 files is between 96 and 192 Kbps not use these extensions for any other types of files.
Page 435: Display
UNDERSTANDING YOUR INSTRUMENT PANEL 433 If a disc has a damaged track which results in audible or Display visible errors that persists for 2.0 seconds, the DVD player Other Language Setup will attempt to continue playing the disc by skipping forward 1.0 to 3.0 seconds at a time.
Page 436 434 UNDERSTANDING YOUR INSTRUMENT PANEL All of the Language settings have a special Other setting selecting the digit, press the remote control’s Right to accommodate languages other than Japanese or Eng- cursor button to select the next digit. Repeat this digit lish.
Page 437 UNDERSTANDING YOUR INSTRUMENT PANEL 435 Rating And Password Setup The default rating is Level 8 (play all discs without a password) and the default password is 0000. The Rating and Password settings work together to control the types of DVDs that your family watches. Most DVD- Video discs have a rating (from 1 to 8) assigned to them where lower numbers are designated for all audiences and higher numbers are designated for more adult audiences.
Page 438 436 UNDERSTANDING YOUR INSTRUMENT PANEL • After the four-digit password is entered, press the remote To set the password, activate the DVD Setup Menu and follow these additional instructions: control’s ENTER/OK button to accept the change. • Using the remote control Left and Right cursor but- tons, select the Rating tab.
Page 439: Product Agreement
UNDERSTANDING YOUR INSTRUMENT PANEL 437 • Using the remote control’s Up and Down cursor To set the rating, activate the DVD Setup Menu and follow these additional instructions: buttons, select the new rating level, and then press the remote control’s ENTER/OK button to accept the •...
Page 440 438 UNDERSTANDING YOUR INSTRUMENT PANEL • THIS PRODUCT IS LICENSED UNDER THE VC-1 Code, you expressly assume all risk and liability associ- ated with downloading and using the Source Code and PATENT PORTFOLIO LICENSE FOR THE PER- complying with the user agreements that accompany SONAL AND NON-COMMERCIAL USE OF A CON- each Source Code.
Page 441 UNDERSTANDING YOUR INSTRUMENT PANEL 439 • This product incorporates copyright protection tech- film and videos and their soundtracks. When a prohib- ited use of an unauthorized copy is detected, a message nology that is protected by U.S. patents and other will be displayed and playback or copying will be intellectual property rights.
Page 442 440 UNDERSTANDING YOUR INSTRUMENT PANEL ABOUT DIVX VIDEO: DivX is a digital video format Trademark created by DivX, LLC, a subsidiary of Rovi Corporation. • Blu-ray Disc™, Blu-ray™ and the logos are trademarks This is an official DivX Certified® device that plays DivX of the Blu-ray Disc Association.
Page 443: Steering Wheel Audio Controls - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 441 STEERING WHEEL AUDIO CONTROLS — IF The remote sound system controls are located on the rear EQUIPPED surface of the steering wheel, at the three and nine o’clock positions. The right-hand rocker switch has a pushbutton in the center, and controls the volume and mode of the sound system.
Page 444: Radio Operation
442 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation CD/DVD/Blu-ray™ Disc MAINTENANCE Pressing the top of the switch will SEEK up for the next To keep a CD/DVD/Blu-ray™ Disc in good condition, listenable station, and pressing the bottom of the switch take the following precautions: will SEEK down for the next listenable station.
Page 445: Radio Operation And Mobile Phones
UNDERSTANDING YOUR INSTRUMENT PANEL 443 NOTE: If you experience difficulty in playing a particular CLIMATE CONTROLS disc, it may be damaged (i.e., scratched, reflective coating The Climate Control system allows you to regulate the removed, a hair, moisture or dew on the disc) oversized, temperature, amount, and direction of air circulating or have protection encoding.
Page 446 444 UNDERSTANDING YOUR INSTRUMENT PANEL The primary control for the rear blower is on the front climate control unit located on the instrument panel. When the front control is in any position other than rear, the front control operates all the rear functions. The rear airflow modes will mirror the front unit opera- tion.
Page 447 UNDERSTANDING YOUR INSTRUMENT PANEL 445 2. Rear Blower Control — If Equipped 5. Right Front Temperature Control Use this control to regulate the amount of air forced Provides right front seat occupant with independent through the rear system in any mode you select. The rear temperature control.
Page 448 446 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The air conditioning compressor may operate in NOTE: Mix and Defrost, even if the A/C button is not pressed. • You can turn off the heated mirror feature at anytime This dehumidifies the air to help dry the windshield. To by pressing the rear window defroster switch a improve fuel economy, use these modes only when second time.
Page 449 UNDERSTANDING YOUR INSTRUMENT PANEL 447 NOTE: CAUTION! (Continued) • If the Recirculation button is pressed when the • Do not use scrapers, sharp instruments, or abrasive system is in Defrost mode the Recirculation LED window cleaners on the interior surface of the indicator will flash three times to indicate Recircula- window.
Page 450 448 UNDERSTANDING YOUR INSTRUMENT PANEL 10. Air Conditioning (A/C) Button 12. Bi-Level Mode Button Press and release to change the current setting. Air is directed through the panel and floor outlets. The indicator illuminates when ON. NOTE: There is a difference in temperature (in any conditions other than full cold or full hot), between the NOTE: If your air conditioning performance seems upper and lower outlets for added comfort.
Page 451: Rear Manual Climate Control - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 449 Economy Mode The rear blower and temperature controls for the rear seat passengers are located in the headliner, near the If ECONOMY mode is desired, press the A/C button to center of the vehicle. turn off the indicator light and the A/C compressor. Rotate the temperature control knob to the desired tem- perature.
Page 452 450 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Blower Control Rear Temperature Control The rear blower control knob can be manually set to off, To change the temperature in the rear of the vehicle, or any fixed blower speed, by rotating the knob from low rotate the temperature knob counterclockwise to lower to high.
Page 453: Automatic Temperature Control (Atc) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 451 • When occupants in the vehicle select the AUTO mode Bi-Level Mode operation, a comfort temperature can be set by using Air comes from both the headliner outlets and the the temperature up and down buttons, and the auto floor outlets.
Page 454 452 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Left Front Seat Occupant Temperature Display This display shows the temperature setting for the left front seat occupant. 3. Mode Display This display shows the current Mode selection (Panel, Bi-Level, Floor, Mix). 4. Blower Control Display This display shows the current Blower speed selection.
Page 455 UNDERSTANDING YOUR INSTRUMENT PANEL 453 7. Right Front Seat Occupant Temperature Display rear climate control screen and allow the front seat occupants control over the rear climate settings. This display shows the temperature setting for the right 11. Rear Lock front seat occupant.
Page 456 454 UNDERSTANDING YOUR INSTRUMENT PANEL 14. Blower Control 18. Driver Temperature Control Up/Down Button There are seven blower speeds, the blower speed in- Provides the driver with independent temperature con- creases as you move the control to the right from the trol.
Page 457 UNDERSTANDING YOUR INSTRUMENT PANEL 455 3. When the system is set up for your comfort level, it is on low until the engine warms up. The fan will engage not necessary to change the settings. You will experi- immediately if the Defrost mode is selected, or by chang- ence the greatest efficiency by simply allowing the ing the front blower knob setting.
Page 458 456 UNDERSTANDING YOUR INSTRUMENT PANEL outlets. If Economy mode is desired, press the A/C To change the rear system settings: button to turn off the A/C mode in the ATC display and • Press REAR button to change control to rear control deactivate the A/C system.
Page 459 UNDERSTANDING YOUR INSTRUMENT PANEL 457 1. Mode Display Bi-Level Mode This display shows the current Mode selection. Air comes from both the headliner outlets and the floor outlets. 2. Rear Temperature Display NOTE: In many temperature positions, the Bi-Level This display shows the temperature setting for the rear mode is designed to provide cooler air out of the head- seat occupants.
Page 460: Understanding Your Instrument Panel
458 UNDERSTANDING YOUR INSTRUMENT PANEL The rear system temperature control is on the front ATC panel located on the instrument panel. Pressing the Rear Temperature Lock button on the front ATC panel, illuminates a lock symbol in the rear display. The rear temperature and air source are controlled from the front ATC panel.
Page 461 UNDERSTANDING YOUR INSTRUMENT PANEL 459 • The temperature can be displayed in English or Metric 2. Rotate the Rear Blower, Rear Temperature and the Rear Mode Control knobs to suit your comfort needs. units by selecting the “Display Units of Measure in” customer-programmable feature.
Page 462 460 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Mode Control CAUTION! (Continued) Auto Mode panel of the 3rd Row seat. Do not block or place objects directly in front of the inlet grille or heater The rear system automatically maintains the correct outlets.
Page 463: Summer Operation
UNDERSTANDING YOUR INSTRUMENT PANEL 461 Floor Mode Summer Operation The engine cooling system must be protected with a Air comes from the floor outlets. high-quality antifreeze coolant to provide proper corro- sion protection and to protect against engine overheating. Recirculation Control OAT coolant (conforming to MS-12106) is recommended.
Page 464: Vacation/Storage
462 UNDERSTANDING YOUR INSTRUMENT PANEL Vacation/Storage Outside Air Intake Before you store your vehicle, or keep it out of service Make sure the air intake, located directly in front of the (i.e., vacation) for two weeks or more, run the air windshield, is free of obstructions such as leaves.
Page 465: Starting And Operating
STARTING AND OPERATING CONTENTS ▫ Key Ignition Park Interlock....476 STARTING PROCEDURES ....467 ▫...
Page 466 464 STARTING AND OPERATING ▫ Tire Identification Number (TIN)...509 POWER STEERING .....490 ▫...
Page 467 STARTING AND OPERATING 465 ▫ Life Of Tire ......526 ▫ Materials Added To Fuel ....543 ▫...
Page 468 466 STARTING AND OPERATING ▫ Common Towing Definitions ... . .554 ADDING FUEL ......549 ▫...
Page 469: Starting Procedures
STARTING AND OPERATING 467 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the • Do not leave the Key Fob in or near the vehicle (or inside and outside mirrors, fasten your seat belt, and if in a location accessible to children), and do not present, instruct all other occupants to buckle their seat leave the ignition of a vehicle equipped with...
Page 470: Keyless Enter-N-Go™ - If Equipped
468 STARTING AND OPERATING Do not press the accelerator. Use the Fob with Integrated CAUTION! Key to briefly turn the ignition switch to the START position and release it as soon as the starter engages. The Damage to the transmission may occur if the follow- starter motor will continue to run, and it will disengage ing precautions are not observed: •...
Page 471: Normal Starting
STARTING AND OPERATING 469 Installing And Removing The ENGINE NOTE: The ENGINE START/STOP button should only START/STOP Button be removed or inserted with the ignition in the OFF position (OFF position for Keyless Enter-N-Go™). Installing The Button Normal Starting 1. Remove the key fob from the ignition switch. Using The ENGINE START/STOP Button 2.
Page 472 470 STARTING AND OPERATING To Turn Off The Engine Using ENGINE NOTE: If the ignition switch is left in the ACC or RUN START/STOP Button (engine not running) position and the transmission is in PARK, the system will automatically time out after 30 1.
Page 473: Extreme Cold Weather (Below -20°F Or −29°C)
STARTING AND OPERATING 471 3. Press the ENGINE START/STOP button a second time If Engine Fails To Start to change the ignition switch to the RUN position (EVIC displays “IGNITION MODE RUN”), WARNING! 4. Press the ENGINE START/STOP button a third time •...
Page 474 472 STARTING AND OPERATING 3. Press and release the ENGINE START/STOP button WARNING! (Continued) once. • If the vehicle has a discharged battery, booster The starter motor will engage automatically, run for 10 cables may be used to obtain a start from a booster seconds, and then disengage.
Page 475: After Starting
STARTING AND OPERATING 473 The starter motor will disengage automatically in 10 ENGINE BLOCK HEATER — IF EQUIPPED seconds. Once this occurs, release the accelerator pedal, The engine block heater warms the engine, and permits turn the ignition switch to the LOCK position, wait 10 to quicker starts in cold weather.
Page 476: Automatic Transmission
474 STARTING AND OPERATING AUTOMATIC TRANSMISSION NOTE: You must press and hold the brake pedal while shifting out of PARK. CAUTION! WARNING! Damage to the transmission may occur if the follow- • It is dangerous to shift out of PARK or NEUTRAL ing precautions are not observed: •...
Page 477 STARTING AND OPERATING 475 WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure • Never leave children alone in a vehicle, or with those in or near the vehicle. As with all vehicles, access to an unlocked vehicle. Allowing children to you should never exit a vehicle while the engine is be in a vehicle unattended is dangerous for a running.
Page 478: Key Ignition Park Interlock
476 STARTING AND OPERATING Key Ignition Park Interlock Brake/Transmission Shift Interlock System This vehicle is equipped with a Key Ignition Park Inter- This vehicle is equipped with a Brake Transmission Shift lock which requires the transmission to be in PARK Interlock System (BTSI) that holds the shift lever in PARK before the ignition switch can be turned to the LOCK unless the brakes are applied.
Page 479: Six-Speed Automatic Transmission
STARTING AND OPERATING 477 • The torque converter clutch may engage at lower engine speeds and remain on longer. • The engine idle speed will be lower. • The overall driving performance will be more conser- vative. • Some ECON mode functions may be temporarily inhibited based on temperature and other factors.
Page 480 478 STARTING AND OPERATING The electronically-controlled transmission provides a Only shift from DRIVE to PARK or REVERSE when the precise shift schedule. The transmission electronics are accelerator pedal is released and the vehicle is stopped. self-calibrating; therefore, the first few shifts on a new Be sure to keep your foot on the brake pedal when vehicle may be somewhat abrupt.
Page 481 STARTING AND OPERATING 479 PARK (P) WARNING! This range supplements the parking brake by locking the • Never use the PARK position as a substitute for the transmission. The engine can be started in this range. parking brake. Always apply the parking brake Never attempt to use PARK while the vehicle is in fully when parked to guard against vehicle move- motion.
Page 482 480 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL • Unintended movement of a vehicle could injure if the engine speed is higher than idle speed. If those in or near the vehicle. As with all vehicles, your foot is not firmly pressing the brake pedal, the you should never exit a vehicle while the engine is vehicle could accelerate quickly forward or in re-...
Page 483 STARTING AND OPERATING 481 • Look at the transmission gear position display and WARNING! (Continued) verify that it indicates the PARK position. • Allowing children to be alone in a vehicle unat- • With brake pedal released, verify that the shift lever tended is dangerous for a number of reasons.
Page 484 482 STARTING AND OPERATING REVERSE (R) CAUTION! This range is for moving the vehicle backward. Shift into Towing the vehicle, coasting, or driving for any other REVERSE only after the vehicle has come to a complete reason with the transmission in NEUTRAL can cause stop.
Page 485 STARTING AND OPERATING 483 while towing heavy trailers), use the Electronic Range Transmission Limp Home Mode Select (ERS) shift control (described below) to select a Transmission function is monitored electronically for lower gear range. Under these conditions, using a lower abnormal conditions.
Page 486 484 STARTING AND OPERATING 3. Turn the ignition switch to the LOCK/OFF position. Electronic Range Select (ERS) Operation The Electronic Range Select (ERS) shift control allows the 4. Wait approximately 10 seconds. driver to limit the highest available gear when the shift 5.
Page 487 STARTING AND OPERATING 485 To exit ERS mode, simply press and hold the shift lever to WARNING! the right (+) until “D” is once again displayed in the instrument cluster. Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury.
Page 488 486 STARTING AND OPERATING Overdrive Operation Torque Converter Clutch The automatic transmission includes an electronically A feature designed to improve fuel economy has been controlled Overdrive (sixth gear). The transmission will included in the automatic transmission on your vehicle. automatically shift into Overdrive if the following con- A clutch within the torque converter engages automati- ditions are present: cally at calibrated speeds.
Page 489: Driving On Slippery Surfaces
STARTING AND OPERATING 487 DRIVING ON SLIPPERY SURFACES Traction When driving on wet or slushy roads, it is possible for a Acceleration wedge of water to build up between the tire and road Rapid acceleration on snow covered, wet, or other slip- surface.
Page 490: Driving Through Water
488 STARTING AND OPERATING DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure shallow standing water, consider the following Cautions safety and prevent damage to your vehicle.
Page 491 STARTING AND OPERATING 489 CAUTION! CAUTION! (Continued) • Driving through standing water may cause damage • Always check the depth of the standing water to your vehicle’s drivetrain components. Always before driving through it. Never drive through inspect your vehicle’s fluids (i.e., engine oil, trans- standing water that is deeper than the bottom of mission, axle, etc.) for signs of contamination (i.e., the tire rims mounted on the vehicle.
Page 492: Starting And Operating Power Steering
490 STARTING AND OPERATING • Upon initial start-up in cold weather, the power steer- POWER STEERING ing pump may make noise for a short amount of time. The standard power steering system will give you good This is due to the cold, thick fluid in the steering vehicle response and increased ease of maneuverability system.
Page 493: Parking Brake
STARTING AND OPERATING 491 apparent, and/or the system is not functioning as antici- If necessary, add fluid to restore to the proper indicated pated. Coordinate inspection efforts through an autho- level. With a clean cloth, wipe any spilled fluid from all rized dealer.
Page 494 492 STARTING AND OPERATING NOTE: • When the parking brake is applied and the automatic transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle.
Page 495 STARTING AND OPERATING 493 WARNING! WARNING! (Continued) • Be sure the parking brake is fully disengaged • When leaving the vehicle, always remove the Key before driving; failure to do so can lead to brake Fob from the ignition and lock your vehicle. failure and a collision.
Page 496: Anti-Lock Brake System (Abs)
494 STARTING AND OPERATING • Brake pedal pulsations. ANTI-LOCK BRAKE SYSTEM (ABS) • A slight drop or fall away of the brake pedal at the end The Anti-Lock Brake System (ABS) provides increased vehicle stability and brake performance under most of the stop.
Page 497: Anti-Lock Brake Warning Light
STARTING AND OPERATING 495 Anti-Lock Brake Warning Light WARNING! (Continued) • The Anti-Lock Brake System cannot prevent colli- The “Anti-Lock Brake Warning Light” moni- sions, including those resulting from excessive tors the anti-lock brake system. The light will speed in turns, following another vehicle too come on when the ignition switch is turned to closely, or hydroplaning.
Page 498: Electronic Brake Control System
496 STARTING AND OPERATING Warning Light” does not come on when the ignition Traction Control System (TCS) switch is turned to the ON position, have the bulb The Traction Control System (TCS) monitors the amount repaired as soon as possible. of wheel spin of each of the driven wheels.
Page 499: Brake Assist System (Bas)
STARTING AND OPERATING 497 your speed and driving to the prevailing road conditions, Brake Assist System (BAS) and do not switch off the ESC or TCS. The Brake Assist System (BAS) is designed to optimize the vehicle’s braking capability during emergency brak- WARNING! ing maneuvers.
Page 500: Electronic Stability Control (Esc)
498 STARTING AND OPERATING wheel to assist in counteracting the over/under steer WARNING! condition. Engine power may also be reduced to help the • The BAS cannot prevent the natural laws of phys- vehicle maintain the desired path. ics from acting on the vehicle, nor can it increase ESC uses sensors in the vehicle to determine the vehicle the traction afforded by prevailing road conditions.
Page 501 STARTING AND OPERATING 499 ESC Operating Modes WARNING! The Electronic Stability Control System (ESC) cannot The “ESC Off” switch is located in the center prevent the natural laws of physics from acting on switch bank, next to the hazard flasher switch. the vehicle, nor can it increase the traction afforded by prevailing road conditions.
Page 502 500 STARTING AND OPERATING When in the “Partial Off” mode, the TCS portion of ESC, WARNING! (Continued) except for the “limited slip” feature described in the TCS reduction feature of TCS is disabled, and the section, has been disabled and the “ESC OFF Indicator enhanced vehicle stability offered by the ESC sys- Light”...
Page 503 STARTING AND OPERATING 501 ESC Activation/Malfunction Indicator Light And The “ESC Activation/Malfunction Indicator Light” (lo- ESC OFF Indicator Light cated in the instrument cluster) starts to flash as soon as the tires lose traction and the ESC system becomes active. The “ESC Activation/Malfunction Indicator Light”...
Page 504: Trailer Sway Control (Tsc)
502 STARTING AND OPERATING • The ESC system will make buzzing or clicking sounds recommendations. Refer to “Trailer Towing” in this sec- when it is active. This is normal; the sounds will stop tion for further information. When TSC is functioning, when ESC becomes inactive following the maneuver the “ESC Activation/Malfunction Indicator Light”...
Page 505 STARTING AND OPERATING 503 brake pedal. If the driver does not apply the throttle HSA will work in REVERSE and all forward gears when during this short period of time, the system will release the activation criteria have been met. The system will not brake pressure and the vehicle will roll down the hill.
Page 506 504 STARTING AND OPERATING For vehicles not equipped with the EVIC, perform the 7. Press the “ESC Off” switch (located in the lower following steps: switch bank below the climate controls) four times within 20 seconds. The “ESC Activation/Malfunction NOTE: You must complete Steps 1 through 8 within 90 Indicator Light”...
Page 507 STARTING AND OPERATING 505 Towing With HSA WARNING! (Continued) HSA will provide assistance when starting on a grade • HSA is not a parking brake. If you stop the vehicle when pulling a trailer. on a hill without putting the transmission in PARK and using the parking brake, it will roll down the WARNING! hill and could cause a collision with another ve-...
Page 508: Tire Safety Information
506 STARTING AND OPERATING TIRE SAFETY INFORMATION NOTE: • P (Passenger) - Metric tire sizing is based on U.S. Tire Markings design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. •...
Page 509 STARTING AND OPERATING 507 • Temporary spare tires are designed for temporary • High flotation tire sizing is based on U.S. design emergency use only. Temporary high pressure com- standards and it begins with the tire diameter molded pact spare tires have the letter “T” or “S” molded into into the sidewall.
Page 510 508 STARTING AND OPERATING EXAMPLE: 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.5 = Section width in inches (in) R = Construction code — R means radial construction — D means diagonal or bias construction 15 = Rim diameter in inches (in) Service Description: 95 = Load Index...
Page 511: Tire Identification Number (Tin)
STARTING AND OPERATING 509 EXAMPLE: Load Identification: ..blank..= Absence of any text on the sidewall of the tire indicates a Standard Load (SL) tire Extra Load (XL) = Extra load (or reinforced) tire Light Load (LL) = Light load tire C, D, E, F, G = Load range associated with the maximum load a tire can carry at a specified pressure Maximum Load—...
Page 512 510 STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation — This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards and is approved for highway use MA = Code representing the tire manufacturing location (two digits) L9 = Code representing the tire size (two digits) ABCD = Code used by the tire manufacturer (one to four digits)
Page 513: Tire Terminology And Definitions
STARTING AND OPERATING 511 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after Cold Tire Inflation Pressure the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
Page 514: Tire Loading And Tire Pressure
512 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. B-Pillar Location For Tire And Loading Information Placard...
Page 515 STARTING AND OPERATING 513 Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4.
Page 516 514 STARTING AND OPERATING Loading To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of The vehicle maximum load on the tire must not exceed occupants and cargo should never exceed XXX lbs or the load carrying capacity of the tire on your vehicle.
Page 517 STARTING AND OPERATING 515 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • If your vehicle will be towing a trailer, load from your “XXX” amount equals 1,400 lbs (635 kg) and there will trailer will be transferred to your vehicle.
Page 518 516 STARTING AND OPERATING...
Page 519: Tires - General Information
STARTING AND OPERATING 517 Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
Page 520: Tire Inflation Pressures
518 STARTING AND OPERATING Ride Comfort And Vehicle Stability WARNING! (Continued) Proper tire inflation contributes to a comfortable ride. • Unequal tire pressures from one side of the vehicle Over-inflation produces a jarring and uncomfortable to the other can cause the vehicle to drift to the ride.
Page 521 STARTING AND OPERATING 519 At least once a month: inflation pressure must not exceed the maximum infla- tion pressure molded into the tire sidewall. • Check and adjust tire pressure with a good quality Check tire pressures more often if subject to a wide range pocket-type pressure gauge.
Page 522: Tire Pressures For High Speed Operation
520 STARTING AND OPERATING Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds and WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
Page 523: Tire Types
STARTING AND OPERATING 521 Consult an authorized tire dealer for tire repairs and Summer Or Three Season Tires — If Equipped additional information. Summer tires provide traction in both wet and dry Damaged Run Flat tires, or Run Flat tires that have conditions, and are not intended to be driven in snow or experienced a loss of pressure should be replaced imme- on ice.
Page 524: Run Flat Tires - If Equipped
522 STARTING AND OPERATING If you need snow tires, select tires equivalent in size and Run Flat Tires — If Equipped type to the original equipment tires. Use snow tires only Run Flat tires allow you the capability to drive 50 miles in sets of four;...
Page 525: Spare Tires - If Equipped
STARTING AND OPERATING 523 Spare Tires — If Equipped rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended NOTE: For vehicles equipped with TIREFIT instead of a tire rotation pattern. spare tire, please refer to “TIREFIT KIT”...
Page 526 524 STARTING AND OPERATING Do not install a wheel cover or attempt to mount a front or rear axle of your vehicle, but it is not. This spare conventional tire on the compact spare wheel, since the tire may have limited tread life. When the tread is worn wheel is designed specifically for the compact spare tire.
Page 527: Tire Spinning
STARTING AND OPERATING 525 Refer to “Freeing A Stuck Vehicle” in “What To Do In WARNING! Emergencies” for further information. Limited-use spares are for emergency use only. In- WARNING! stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the Fast spinning tires can be dangerous.
Page 528: Life Of Tire
526 STARTING AND OPERATING tread wear indicators, the tire should be replaced. Refer to “Replacement Tires” in this section for further infor- mation. Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: •...
Page 529: Replacement Tires
STARTING AND OPERATING 527 Information placard or the Vehicle Certification Label for WARNING! the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original Tires and the spare tire should be replaced after six equipment tire sidewall.
Page 530: Tire Chains (Traction Devices)
528 STARTING AND OPERATING WARNING! WARNING! (Continued) • Failure to equip your vehicle with tires having • Do not use a tire, wheel size or rating other than that adequate speed capability can result in sudden tire specified for your vehicle. Some combinations of failure and loss of vehicle control.
Page 531 STARTING AND OPERATING 529 • Install on front tires only. CAUTION! • On a 225/65R16 100H use of a traction device that To avoid damage to your vehicle or tires, observe the meets the SAE type “Class S” specification is recom- following precautions: mended.
Page 532: Tire Rotation Recommendations
530 STARTING AND OPERATING These effects can be reduced by timely rotation of tires. CAUTION! (Continued) The benefits of rotation are especially worthwhile with • Observe the traction device manufacturer’s instruc- aggressive tread designs such as those on all season type tions on the method of installation, operating tires.
Page 533: Tire Pressure Monitor System (Tpms)
STARTING AND OPERATING 531 The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12°F (6.5°C). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure.
Page 534 532 STARTING AND OPERATING The TPMS will continue to warn the driver of low tire For example, your vehicle may have a recommended pressure as long as the condition exists, and will not turn cold (parked for more than three hours) tire placard off until the tire pressure is at or above recommended pressure of 35 psi (241 kPa).
Page 535 STARTING AND OPERATING 533 NOTE: CAUTION! • The TPMS is not intended to replace normal tire care • The TPMS has been optimized for the original and maintenance, or to provide warning of a tire equipment tires and wheels. TPMS pressures have failure or condition.
Page 536: Base System
534 STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, Tire Pressure Monitoring Low Tire Pressure and the TPMS will monitor the actual tire pressure in Warnings the tire. The “Tire Pressure Monitoring Telltale Light” Base System will illuminate in the instrument cluster, a The TPMS uses wireless technology with wheel rim “LOW TIRE PRESSURE”...
Page 537 STARTING AND OPERATING 535 • Accumulation of excessive snow and/or ice around NOTE: The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this infor- the wheels or wheel housings. mation. •...
Page 538: Premium System - If Equipped
536 STARTING AND OPERATING • After driving for up to 20 minutes above 15 mph Premium System — If Equipped (24 km/h), the “Tire Pressure Monitoring Telltale The TPMS uses wireless technology with wheel rim- Light” will flash on and off for 75 seconds and then mounted electronic sensors to monitor tire pressure lev- remain on solid.
Page 539 STARTING AND OPERATING 537 TPMS Low Pressure Warnings NOTE: The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this infor- The “Tire Pressure Monitoring Telltale Light” will illumi- mation. nate in the instrument cluster, and an audible chime will be activated when one or more of the four active road tire SERVICE TPM SYSTEM Message pressures are low.
Page 540 538 STARTING AND OPERATING message will not be present, and a pressure value will be message is then followed by a graphic display with displayed instead of dashes. A system fault can occur by pressure values still shown. This indicates that the pres- any of the following scenarios: sure values are still being received from the TPM sensors but they may not be in the correct vehicle position.
Page 541 STARTING AND OPERATING 539 • After driving the vehicle for up to 20 minutes above pressure value instead of dashes (- -), as long no tire 15 mph (24 km/h), the “Tire Pressure Monitoring pressure is below the low pressure warning limit in Telltale Light”...
Page 542: Fuel Requirements
540 STARTING AND OPERATING The TPM sensors are regulated under one of the follow- Light spark knock at low engine speeds is not harmful to ing licenses: your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is United States MRXC4W4MA4 required.
Page 543: Reformulated Gasoline
STARTING AND OPERATING 541 Reformulated Gasoline CAUTION! Many areas of the country require the use of cleaner DO NOT use gasoline containing Methanol or gaso- burning gasoline referred to as “Reformulated Gasoline”. line containing more than 10% Ethanol. Use of these Reformulated gasolines contain oxygenates and are spe- blends may result in starting and drivability prob- cifically blended to reduce vehicle emissions and im-...
Page 544: E-85 Usage In Non-Flex Fuel Vehicles
542 STARTING AND OPERATING E-85 Usage In Non-Flex Fuel Vehicles To fix a Non-FFV vehicle inadvertently fueled once with E-85 perform the following: Non-Flex Fuel Vehicles (FFV) are compatible with gaso- • Drain the fuel tank (see your authorized dealer). line containing 10% ethanol (E10).
Page 545: Materials Added To Fuel
STARTING AND OPERATING 543 without MMT be used in your vehicle. The MMT content Fuel System Cautions of gasoline may not be indicated on the gasoline pump, therefore, you should ask your gasoline retailer whether CAUTION! the gasoline contains MMT. MMT is prohibited in Federal Follow these guidelines to maintain your vehicle’s and California reformulated gasoline.
Page 546: Carbon Monoxide Warnings
544 STARTING AND OPERATING Carbon Monoxide Warnings CAUTION! (Continued) • The use of fuel additives, which are now being WARNING! sold as octane enhancers, is not recommended. Carbon monoxide (CO) in exhaust gases is deadly. Most of these products contain high concentrations Follow the precautions below to prevent carbon of methanol.
Page 547: Flexible Fuel - If Equipped
STARTING AND OPERATING 545 WARNING! (Continued) • Guard against carbon monoxide with proper main- tenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. FLEXIBLE FUEL —...
Page 548: Ethanol Fuel (E-85)
546 STARTING AND OPERATING WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap) or filling the tank.
Page 549: Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles
E-85 fuel, you may experience tensive fleet testing, to provide additional protection to hard starting and rough idle following start up even if Chrysler Group LLC engines. Use MOPAR® or an the above recommendations are followed, especially equivalent oil meeting the specification MS-6395.
Page 550: Starting
548 STARTING AND OPERATING Starting Replacement Parts The characteristics of E-85 fuel make it unsuitable for use Many components in your Flexible Fuel Vehicle (FFV) are when ambient temperatures fall below 0°F (-18°C). In the designed to be compatible with ethanol. Always be sure range of 0°F (-18°C) to 32°F (0°C), you may experience an that your vehicle is serviced with correct ethanol com- increase in the time it takes for your engine to start, and...
Page 551: Starting And Operating Adding Fuel
STARTING AND OPERATING 549 ADDING FUEL NOTE: The driver’s side sliding door cannot be opened while the fuel door is open. This feature operates only Fuel Filler Cap (Gas Cap) when the sliding door is fully closed prior to opening the The gas cap is located behind the fuel filler door on the fuel door.
Page 552: Loose Fuel Filler Cap Message
550 STARTING AND OPERATING • Tighten the fuel filler cap until you hear a “clicking” WARNING! sound. This is an indication that the fuel filler cap is • Never have any smoking materials lit in or near the properly tightened. vehicle when the gas cap is removed or the tank is •...
Page 553: Vehicle Loading
STARTING AND OPERATING 551 properly tightened. Refer to “Onboard Diagnostic Sys- The label contains the following information: tem” in “Maintaining Your Vehicle” for further informa- • Name of manufacturer tion. • Month and year of manufacture If the problem continues, the message will appear the •...
Page 554 552 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) Rim Size The GAWR is the maximum capacity of the front and rear This is the rim size that is appropriate for the tire size axles. Distribute the load over the front and rear axles listed.
Page 555 STARTING AND OPERATING 553 Overloading Loading The load carrying components (axle, springs, tires, To load your vehicle properly, first figure out its empty wheels, etc.) of your vehicle will provide satisfactory weight, axle-by-axle and side-by-side. Store heavier items service as long as you do not exceed the GVWR and the down low and be sure you distribute their weight as front and rear GAWR.
Page 556: Trailer Towing
554 STARTING AND OPERATING TRAILER TOWING exceed the GVWR. Refer to “Vehicle Loading/Vehicle Certification Label” in “Starting and Operating” for In this section you will find safety tips and information further information. on limits to the type of towing you can reasonably do with your vehicle.
Page 557 STARTING AND OPERATING 555 rear GAWR. Refer to “Vehicle Loading/Vehicle Certifica- Frontal Area tion Label” in “Starting and Operating” for further The frontal area is the maximum height multiplied by the information. maximum width of the front of a trailer. Trailer Sway Control WARNING! The trailer sway control can be a mechanical telescoping...
Page 558 556 STARTING AND OPERATING Weight-Carrying Hitch Trailer sway control and a weight distributing (load equalizing) hitch are recommended for heavier Tongue A weight-carrying hitch supports the trailer tongue Weights (TW) and may be required depending on vehicle weight, just as if it were luggage located at a hitch ball or and trailer configuration/loading to comply with Gross some other connecting point of the vehicle.
Page 559 STARTING AND OPERATING 557 Trailer Hitch Classification Trailer Hitch Classification Definitions The following chart provides the industry standard for Class Max. Trailer Hitch In- the maximum trailer weight a given trailer hitch class can dustry Standards tow and should be used to assist you in selecting the Class III - Heavy Duty 5,000 lbs (2 268 kg) correct trailer hitch for your intended towing condition.
Page 560 558 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. GCWR (Gross Engine/ Max. GTW (Gross Max. Tongue Combined Weight Frontal Area Transmission Trailer Weight) Weight Rating) 8,750 lbs (3 969 kg)
Page 561 STARTING AND OPERATING 559 NOTE: The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the Tire and Loading Information placard. Refer to “Tire Safety Information”...
Page 562 560 STARTING AND OPERATING NOTE: Remember that everything put into or on the CAUTION! trailer adds to the load on your vehicle. Also, additional • Do not tow a trailer at all during the first 500 miles factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.
Page 563 STARTING AND OPERATING 561 WARNING! WARNING! (Continued) • Safety chains must always be used between your Improper towing can lead to a collision. Follow these vehicle and trailer. Always connect the chains to guidelines to make your trailer towing as safe as the hook retainers of the vehicle hitch.
Page 564 562 STARTING AND OPERATING • Proper tire inflation pressures are essential to the safe WARNING! (Continued) and satisfactory operation of your vehicle. Refer to • Total weight must be distributed between the tow “Tires – General Information” in “Starting And Oper- vehicle and the trailer such that the following four ating”...
Page 565 STARTING AND OPERATING 563 Towing Requirements — Trailer Brakes WARNING! • Do not interconnect the hydraulic brake system or • Do not connect trailer brakes to your vehicle’s hydrau- vacuum system of your vehicle with that of the trailer. lic brake lines. It can overload your brake system and This could cause inadequate braking and possible cause it to fail.
Page 566 564 STARTING AND OPERATING Towing Requirements — Trailer Lights And Wiring Whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a four- and seven- pin wiring harness.
Page 567: Towing Tips
STARTING AND OPERATING 565 Towing Tips Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Automatic Transmission The DRIVE gear can be selected when towing. However, if frequent shifting occurs while in DRIVE, use the Electronic Range Select (ERS) shift control to select a lower gear range.
Page 568 566 STARTING AND OPERATING If you REGULARLY tow a trailer for more than 45 Cooling System minutes of continuous operation, then change the trans- To reduce potential for engine and transmission over- mission fluid and filter as specified for “police, taxi, fleet, heating, take the following actions: or frequent trailer towing.”...
Page 569: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 567 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheels OFF the Ground All Models Flat Tow NONE NOT ALLOWED Dolly Tow Front Rear NOT ALLOWED On Trailer...
Page 570: Recreational Towing - All Models
568 STARTING AND OPERATING Recreational Towing — All Models CAUTION! Recreational towing is allowed ONLY if the front wheels DO NOT flat tow this vehicle. Damage to the drive- are OFF the ground. This may be accomplished using a train will result. tow dolly or vehicle trailer.
Page 571: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS HAZARD WARNING FLASHERS ...571 JACKING AND TIRE CHANGING — IF EQUIPPED ......585 IF YOUR ENGINE OVERHEATS .
Page 572 570 WHAT TO DO IN EMERGENCIES ▫ Road Tire Installation ....603 FREEING A STUCK VEHICLE ... . .609 JUMP-STARTING .
Page 573: Hazard Warning Flashers
WHAT TO DO IN EMERGENCIES 571 HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located in the In any of the following situations, you can reduce the lower center area of the instrument panel. potential for overheating by taking the appropriate action. •...
Page 574: Tirefit Kit - If Equipped
572 WHAT TO DO IN EMERGENCIES TIREFIT KIT — IF EQUIPPED CAUTION! Small punctures up to ¼” (6 mm) in the tire tread can be Driving with a hot cooling system could damage sealed with TIREFIT. Foreign objects (e.g., screws or your vehicle.
Page 575 WHAT TO DO IN EMERGENCIES 573 TIREFIT Kit Location TIREFIT Kit 1. Open the liftgate. 2. Turn the two rear left side trim panel latches to release the trim panel.
Page 576: Tirefit Kit Components And Operation
574 WHAT TO DO IN EMERGENCIES TIREFIT Kit Components And Operation Using The Mode Select Knob And Hoses Your TIREFIT kit is equipped with the following symbols to indicate the air or sealant mode. Selecting Air Mode Push in the Mode Select Knob (5) and turn to this position for air pump operation only.
Page 577: Tirefit Usage Precautions
WHAT TO DO IN EMERGENCIES 575 Using The Power Button Push and release the Power Button (4) once to turn On the TIREFIT kit. Push and release the Power Button (4) again to turn Off the TIREFIT kit. Using The Deflation Button Press the Deflation Button (2) to reduce the air pressure in the tire if it becomes over-inflated.
Page 578 576 WHAT TO DO IN EMERGENCIES • When the TIREFIT sealant is in a liquid form, clean • Do not lift or carry the TIREFIT kit by the hoses. water, and a damp cloth will remove the material from the vehicle or tire and wheel components. Once the WARNING! sealant dries, it can easily be peeled off and properly •...
Page 579 WHAT TO DO IN EMERGENCIES 577 WARNING! (Continued) WARNING! (Continued) • Take care not to allow the contents of TIREFIT to – If you are unsure of the condition of the tire or the wheel. come in contact with hair, eyes, or clothing. TIRE- •...
Page 580: Sealing A Tire With Tirefit
578 WHAT TO DO IN EMERGENCIES Sealing A Tire With TIREFIT (B) Setting Up To Use TIREFIT: (A) Whenever You Stop To Use TIREFIT: 1. Push in the Mode Select Knob (5) and turn to the Sealant Mode position. 1. Pull over to a safe location and turn on the vehicle’s Hazard Warning flashers.
Page 581 WHAT TO DO IN EMERGENCIES 579 (C) Injecting TIREFIT Sealant Into The Deflated the Sealant Hose (6) to the valve stem. Check that the Tire: Mode Select Knob (5) is in the Sealant Mode position and not Air Mode. Press the Power Button (4) to turn •...
Page 582 580 WHAT TO DO IN EMERGENCIES If the sealant (white fluid) does flow through the If the tire does not inflate to at least 26 psi (1.8 Bar) Sealant Hose (6): pressure within 15 minutes: • The tire is too badly damaged. Do not attempt to drive 1.
Page 583 WHAT TO DO IN EMERGENCIES 581 3. Immediately disconnect the Sealant Hose (6) from the (D) Drive Vehicle: valve stem, reinstall the cap on the fitting at the end of Immediately after injecting sealant and inflating the tire, the hose, and place the TIREFIT kit in the vehicle drive the vehicle 5 miles (8 km) or 10 minutes to ensure storage location.
Page 584 582 WHAT TO DO IN EMERGENCIES (E) After Driving: If the tire pressure is 19 psi (1.3 Bar) or higher: Pull over to a safe location. Refer to “Whenever You Stop 1. Press the Power Button (4) to turn on TIREFIT and to Use TIREFIT”...
Page 585: Wheel And Tire Torque Specifications
WHAT TO DO IN EMERGENCIES 583 5. Replace the Sealant Bottle (1) and Sealant Hose (6) 5. Position the new Sealant Bottle (1) in the housing so assembly at your authorized dealer as soon as pos- that the Sealant Hose (6) aligns with the hose slot in sible.
Page 586: Torque Specifications
100 Ft-Lbs (135 N·m) M12 x 1.25 19 mm **Use only Chrysler recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.
Page 587: Jacking And Tire Changing - If Equipped
WHAT TO DO IN EMERGENCIES 585 WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. JACKING AND TIRE CHANGING —...
Page 588: Jack Location
586 WHAT TO DO IN EMERGENCIES Jack Location WARNING! (Continued) The jack, jack handle and winch handle tools are stowed • Being under a jacked-up vehicle is dangerous. The behind the rear left side trim panel in the rear cargo area. vehicle could slip off the jack and fall on you.
Page 589: Spare Tire Removal
WHAT TO DO IN EMERGENCIES 587 Spare Tire Removal The spare tire is stowed inside a protective cover located under the center of the vehicle between the front doors by means of a cable winch mechanism. The “spare tire drive” nut is located on the floor, under a plastic cap at the front of the floor console or under front super console forward bin liner.
Page 590: To Access Spare Tire Winch Drive Nut
588 WHAT TO DO IN EMERGENCIES To Access Spare Tire Winch Drive Nut To access the spare tire winch drive nut and lower the spare tire, you will need to refer to one of the following center console configurations. Super Console For vehicles equipped with the Super Console, the spare tire winch assembly drive nut is located beneath the console.
Page 591 WHAT TO DO IN EMERGENCIES 589 2. Open the front drawer to expose the storage compart- Premium/Base/Cargo Center Console ment. Pull the Winch Cover assembly plug (if equipped) to access the winch drive nut. 3. Remove the liner from the console’s storage compart- ment to access the spare tire winch drive nut.
Page 592: Spare Tire Tools
590 WHAT TO DO IN EMERGENCIES Spare Tire Tools The tool pouch contains three pieces and can be as- sembled into a spare tire hook; to remove the compact spare tire/cover assembly from under the vehicle, or a Winch T-handle; to raise/lower the compact spare tire/ cover assembly.
Page 593: Spare Tire Removal Instructions
WHAT TO DO IN EMERGENCIES 591 Spare Tire Removal Instructions The spare tire is located under the vehicle beneath the center console area. Assembling The Spare Tire Hook A — Spare Tire Hook/T-handle B — Extension 1 C — Extension 2 Spare Tire And Cover 1.
Page 594 592 WHAT TO DO IN EMERGENCIES 2. Rotate the nut to the left until the winch mechanism stops turning freely. This will allow enough slack in the cable to allow you to pull the spare tire out from underneath the vehicle. CAUTION! The winch mechanism is designed for use with the winch T-handle only.
Page 595: Preparations For Jacking
WHAT TO DO IN EMERGENCIES 593 4. Stand the tire/cover assembly upright and remove the Preparations For Jacking wheel spacer by squeezing the winch retaining tabs 1. Park the vehicle on a firm, level surface. Avoid ice or together. Push the retainer through the spare tire to slippery areas.
Page 596: Jacking Instructions
594 WHAT TO DO IN EMERGENCIES 6. Block both the front and rear of the wheel diagonally Jacking Instructions opposite of the jacking position. For example, if changing the right front WARNING! tire, block the left rear wheel. Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: •...
Page 597 WHAT TO DO IN EMERGENCIES 595 WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a Jack Warning Label service center where it can be raised on a lift.
Page 598 596 WHAT TO DO IN EMERGENCIES 2. There are two jack engagement locations on each side Rear jack locations are between a pair of down-facing of the vehicle body. These locations are on the sill tabs on the sill flange of the vehicle side body. flange of the vehicle body.
Page 599 WHAT TO DO IN EMERGENCIES 597 Rear Jack Engaged Front Jack Locations Front jack location is on the sill flange of the vehicle body and is located 6 in (150 mm) from door edge.
Page 600 598 WHAT TO DO IN EMERGENCIES WARNING! Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.
Page 601 WHAT TO DO IN EMERGENCIES 599 WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the wheel lug nuts, for vehicles with wheel covers, remove the cover from the wheel by hand.
Page 602 600 WHAT TO DO IN EMERGENCIES NOTE: Do not install the wheel cover on the compact 10. Place the deflated (flat) tire and compact spare tire spare. cover assembly in the rear cargo area. Do not stow the deflated tire in the compact spare tire location. 7.
Page 603: Securing The Compact Spare Tire
WHAT TO DO IN EMERGENCIES 601 Securing The Compact Spare Tire CAUTION! 1. Assemble the winch handle extensions to form a The winch mechanism is designed for use with the T-handle and fit the winch T-handle over the drive winch T-handle only. Use of an air wrench or other nut.
Page 604 602 WHAT TO DO IN EMERGENCIES 4. Using the winch T-handle, rotate the drive nut to the CAUTION! right until the compact spare tire/cover assembly is drawn into place against the underside of the vehicle. The compact spare tire/cover assembly must be used when the compact spare tire is stored.
Page 605: Road Tire Installation
WHAT TO DO IN EMERGENCIES 603 Road Tire Installation Vehicles Equipped With Wheel Covers 1. Mount the road tire on the axle. 2. To ease the installation process for steel wheels with wheel covers, install two lug nuts on the mounting studs which are on each side of the valve stem.
Page 606 604 WHAT TO DO IN EMERGENCIES 3. Align the valve notch in the wheel cover with the 6. Refer to “Torque Specifications” in this section for valve stem on the wheel. Install the cover by hand, proper wheel lug nut torque. snapping the cover over the two lug nuts.
Page 607: Jump-Starting
WHAT TO DO IN EMERGENCIES 605 3. Lower the vehicle to the ground by turning the jack NOTE: When using a portable battery booster pack handle counterclockwise. follow the manufacturer’s operating instructions and precautions. 4. Refer to “Torque Specifications” in this section for proper wheel lug nut torque.
Page 608: Preparations For Jump-Start
606 WHAT TO DO IN EMERGENCIES Preparations For Jump-Start WARNING! The battery in your vehicle is located on the left side of • Take care to avoid the radiator cooling fan when- the engine compartment. ever the hood is raised. It can start anytime the ignition switch is ON.
Page 609: Jump-Starting Procedure
WHAT TO DO IN EMERGENCIES 607 3. If using another vehicle to jump-start the battery, park CAUTION! the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. Failure to follow these procedures could result in damage to the charging system of the booster vehicle WARNING! or the discharged vehicle.
Page 610 608 WHAT TO DO IN EMERGENCIES 4. Connect the opposite end of the negative (-) jumper 6. Once the engine is started, remove the jumper cables cable to a good engine ground (exposed metal part of in the reverse sequence: the discharged vehicle’s engine) away from the battery Disconnecting The Jumper Cables and the fuel injection system.
Page 611: Freeing A Stuck Vehicle
WHAT TO DO IN EMERGENCIES 609 CAUTION! CAUTION! Accessories plugged into the vehicle power outlets Racing the engine or spinning the wheels may lead to draw power from the vehicle’s battery, even when not transmission overheating and failure. Allow the en- in use (i.e., cellular phones, etc.).
Page 612: Shift Lever Override
610 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! (Continued) explode and injure someone. Do not spin your vehi- • When “rocking” a stuck vehicle by shifting be- cle’s wheels faster than 30 mph (48 km/h) or for tween DRIVE and REVERSE, do not spin the longer than 30 seconds continuously without stop- wheels faster than 15 mph (24 km/h), or drivetrain ping when you are stuck and do not let anyone near...
Page 613 WHAT TO DO IN EMERGENCIES 611 3. Using a small screwdriver or similar tool, remove the 4. Press and maintain firm pressure on the brake pedal. shift lever override access cover (located near the top 5. Insert the screwdriver or similar tool into the access right of the shift lever in the instrument panel).
Page 614: Towing A Disabled Vehicle
612 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial wrecker service. Towing Condition Wheels OFF the Ground ALL MODELS Flat Tow NONE If transmission is operable: • Transmission in NEUTRAL Wheel lift Rear •...
Page 615 WHAT TO DO IN EMERGENCIES 613 Proper towing or lifting equipment is required to prevent CAUTION! damage to your vehicle. Use only tow bars and other • Do not use sling type equipment when towing. equipment designed for this purpose, following equip- ment manufacturer’s instructions.
Page 616 614 WHAT TO DO IN EMERGENCIES The manufacturer recommends towing your vehicle with CAUTION! all four wheels OFF the ground using a flatbed. If flatbed equipment is not available, and the transmission is Towing faster than 25 mph (40 km/h) or farther than operable, the vehicle may be flat towed (with all four 15 mi (24 km) with front wheels on the ground can wheels on the ground) under the following conditions:...
Page 617: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS ▫ Engine Air Cleaner Filter ....625 ENGINE COMPARTMENT — 3.6L ..617 ▫ Exhaust System ..... .626 ONBOARD DIAGNOSTIC SYSTEM —...
Page 618 616 MAINTAINING YOUR VEHICLE ▫ Appearance Care And Protection From ▫ Front Side Marker Lamp ....662 Corrosion ......645 ▫...
Page 619: Engine Compartment - 3.6L
MAINTAINING YOUR VEHICLE 617 ENGINE COMPARTMENT — 3.6L 1 — Air Filter 6 — Engine Coolant Reservoir 2 — Power Steering Fluid Reservoir 7 — Engine Oil Dipstick 3 — Brake Fluid Reservoir 8 — Engine Oil Fill 4 — Battery 9 —...
Page 620: Onboard Diagnostic System - Obd Ii
618 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated Onboard • Prolonged driving with the MIL on could cause Diagnostic system called OBD II. This system monitors further damage to the emission control system. It the performance of the emissions, engine, and automatic could also affect fuel economy and driveability.
Page 621: Emissions Inspection And Maintenance Programs
MAINTAINING YOUR VEHICLE 619 “Electronic Vehicle Information Center (EVIC)” in ”Un- EMISSIONS INSPECTION AND MAINTENANCE derstanding Your Instrument Panel” for further informa- PROGRAMS tion. Tighten the gas cap until a clicking sound is heard. In some localities, it may be a legal requirement to pass This is an indication that the gas cap is properly tight- an inspection of your vehicle’s emissions control system.
Page 622 620 MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition key-actuated test, the ignition or start the engine. This means that your which you can use prior to going to the test station. To vehicle’s OBD II system is not ready and you should check if your vehicle’s OBD II system is ready, you must not proceed to the I/M station.
Page 623: Replacement Parts
MAINTAINING YOUR VEHICLE 621 before going to the I/M station. The I/M station can fail NOTE: Intentional tampering with emissions control your vehicle because the MIL is on with the engine systems may void your warranty and could result in civil running.
Page 624 622 MAINTAINING YOUR VEHICLE Besides those maintenance items specified in the fixed CAUTION! (Continued) “Maintenance Schedule”, there are other components • Your vehicle has been built with improved fluids which may require servicing or replacement in the future. that protect the performance and durability of your vehicle and also allow extended maintenance inter- CAUTION! vals.
Page 625: Engine Oil
MIN mark will result in a MAX reading on these recommends engine oils that are API Certified and meet engines. the requirements of Chrysler Material Standard MS-6395. CAUTION! Overfilling or underfilling will cause oil aeration, or loss of oil pressure. This could damage your engine.
Page 626 American Petroleum Institute (API) Engine Oil Engine Oil Viscosity — 3.6L Engine Identification Symbol MOPAR® SAE 5W-20 engine oil approved to Chrysler Material Standard MS-6395 such as Pennzoil®, Shell This symbol means that the oil has Helix® or equivalent. is recommended for all operating been certified by the American temperatures.
Page 627: Engine Oil Filter
MAINTAINING YOUR VEHICLE 625 Synthetic Engine Oils station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in You may use synthetic engine oils provided the recom- your area. mended oil quality requirements are met, and the recom- mended maintenance intervals for oil and filter changes Engine Oil Filter are followed.
Page 628: Exhaust System
626 MAINTAINING YOUR VEHICLE Exhaust System WARNING! The best protection against carbon monoxide entry into The air induction system (air cleaner, hoses, etc.) can the vehicle body is a properly maintained engine exhaust provide a measure of protection in the case of engine system.
Page 629 MAINTAINING YOUR VEHICLE 627 WARNING! CAUTION! • Exhaust gases can injure or kill. They contain • The catalytic converter requires the use of un- carbon monoxide (CO), which is colorless and leaded fuel only. Leaded gasoline will destroy the odorless. Breathing it can make you unconscious effectiveness of the catalyst as an emissions control and can eventually poison you.
Page 630: Maintenance-Free Battery
628 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter dam- verter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage.
Page 631 MAINTAINING YOUR VEHICLE 629 WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can • It is essential when replacing the cables on the burn or even blind you. Do not allow battery fluid battery that the positive cable is attached to the to contact your eyes, skin, or clothing.
Page 632: Air Conditioner Maintenance
630 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance WARNING! (Continued) For best possible performance, your air conditioner should • The air conditioning system contains refrigerant be checked and serviced by an authorized dealer at the start under high pressure. To avoid risk of personal of each warm season.
Page 633 MAINTAINING YOUR VEHICLE 631 Refrigerant Recovery And Recycling WARNING! R-134a Air Conditioning Refrigerant is a hydrofluoro- Do not remove the A/C air filter while the blower is carbon (HFC) that is endorsed by the Environmental operating or personal injury may result. Protection Agency and is an ozone-saving product.
Page 634: Body Lubrication
632 MAINTAINING YOUR VEHICLE CAUTION! The A/C air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 7. Rotate the glove compartment door back into position. Body Lubrication Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate,...
Page 635: Windshield Wiper Blades
MAINTAINING YOUR VEHICLE 633 attention should also be given to hood latching compo- Avoid using the wiper blades to remove frost or ice from nents to ensure proper function. When performing other the windshield. Keep the blade rubber out of contact with underhood services, the hood latch, release mechanism petroleum products such as engine oil, gasoline, etc.
Page 636: Cooling System
634 MAINTAINING YOUR VEHICLE The washer fluid reservoir will hold a full gallon of fluid Cooling System when the Low Washer Fluid Light illuminates. WARNING! WARNING! • When working near the radiator cooling fan, Commercially available windshield washer solvents disconnect the fan motor lead or turn the ignition are flammable.
Page 637 MAINTAINING YOUR VEHICLE 635 Coolant Checks bottle. DO NOT REMOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT. Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where Cooling System — Drain, Flush And Refill applicable).
Page 638 636 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! (Continued) • Do not use water alone or alcohol-based engine • Mixing of engine coolant (antifreeze) other than coolant (antifreeze) products. Do not use additional specified Organic Additive Technology (OAT) en- rust inhibitors or antirust products, as they may not gine coolant (antifreeze), may result in engine be compatible with the radiator engine coolant and damage and may decrease corrosion protection.
Page 639 Please review these recommendations for using Organic engine cooling system. Additive Technology (OAT) engine coolant (antifreeze) that meets the requirements of Chrysler Material Stan- Please note that it is the owner’s responsibility to main- dard MS-12106. When adding engine coolant (antifreeze):...
Page 640 638 MAINTAINING YOUR VEHICLE • Mixing engine coolant (antifreeze) types is not recom- WARNING! mended and can result in cooling system damage. If • The warning words “DO NOT OPEN HOT” on the HOAT and OAT coolant are mixed in an emergency, have a authorized dealer drain, flush, and refill with cooling system pressure cap are a safety precaution.
Page 641 OAT coolant that meets puddles on the ground. If ingested by a child or pet, seek the requirements of Chrysler Material Standard MS- emergency assistance immediately. Clean up any ground 12106 should be added to the coolant bottle. Do not spills immediately.
Page 642: Brake System
640 MAINTAINING YOUR VEHICLE • Keep the front of the radiator clean. If your vehicle is If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be equipped with air conditioning, keep the front of the safely driven.
Page 643 MAINTAINING YOUR VEHICLE 641 Clean the top of the master cylinder area before removing WARNING! the cap. Add fluid to bring the level up to the top of the “FULL” mark on the side of the master cylinder reservoir. Riding the brakes can lead to brake failure and possibly a collision.
Page 644 642 MAINTAINING YOUR VEHICLE WARNING! WARNING! (Continued) • To avoid contamination from foreign matter or • Use only manufacturer’s recommended brake moisture, use only new brake fluid or fluid that has fluid. Refer to “Fluids, Lubricants, and Genuine been in a tightly closed container. Keep the master Parts”...
Page 645: Automatic Transmission
MAINTAINING YOUR VEHICLE 643 WARNING! (Continued) CAUTION! • Do not allow petroleum based fluid to contaminate Using a transmission fluid other than the manufactur- the brake fluid. Brake seal components could be er’s recommended fluid may cause deterioration in damaged, causing partial or complete brake failure. transmission shift quality and/or torque converter This could result in a collision.
Page 646 644 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! If a transmission fluid leak occurs, visit your autho- Do not use chemical flushes in your transmission as rized dealer immediately. Severe transmission dam- the chemicals can damage your transmission compo- age may occur. Your authorized dealer has the proper nents.
Page 647: Appearance Care And Protection From
MAINTAINING YOUR VEHICLE 645 Appearance Care And Protection From Corrosion What Causes Corrosion? Corrosion is the result of deterioration or removal of Protection Of Body And Paint From Corrosion paint and protective coatings from your vehicle. Vehicle body care requirements vary according to geo- graphic locations and usage.
Page 648 646 MAINTAINING YOUR VEHICLE • If insects, tar, or other similar deposits have accumu- Special Care lated on your vehicle, use MOPAR® Super Kleen Bug • If you drive on salted or dusty roads or if you drive and Tar Remover to remove. near the ocean, hose off the undercarriage at least once •...
Page 649 MAINTAINING YOUR VEHICLE 647 • If you carry special cargo such as chemicals, fertilizers, • For aluminum wheels, use MOPAR® Wheel Cleaner de-icer salt, etc., be sure that such materials are well (Part# 04796239AB) or equivalent. packaged and sealed. CAUTION! •...
Page 650 648 MAINTAINING YOUR VEHICLE • Blot any remaining stain with a clean, damp towel. Cleaning Interior Trim • For tough stains, apply MOPAR® Total Clean, or a Interior trim should be cleaned starting with a damp mild soap solution to a clean, damp cloth and remove cloth, a damp cloth with MOPAR®...
Page 651 MAINTAINING YOUR VEHICLE 649 liquid. Please do not use polishes, oils, cleaning fluids, To minimize the possibility of scratching the lenses and solvents, detergents, or ammonia-based cleaners to clean reducing light output, avoid wiping with a dry cloth. To your leather upholstery. Application of a leather condi- remove road dirt, wash with a mild soap solution fol- tioner is not required to maintain the original condition.
Page 652: Cleaning The Instrument Panel Cupholders
650 MAINTAINING YOUR VEHICLE Cleaning Plastic Instrument Cluster Lenses Replace the belts if they appear frayed or worn or if the buckles do not work properly. The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care Cleaning The Instrument Panel Cupholders must be taken to avoid scratching the plastic.
Page 653: Fuses
MAINTAINING YOUR VEHICLE 651 Installation WARNING! (Continued) Place the liner into the cupholder drawer and press the • Before replacing a fuse, make sure that the ignition liner into place so that the retention tabs seat into the is off and that all the other services are switched off corresponding openings in the drawer.
Page 654 652 MAINTAINING YOUR VEHICLE CAUTION! • When installing the Totally Integrated Power Mod- ule cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure.
Page 655 MAINTAINING YOUR VEHICLE 653 Cavity Cartridge Fuse Mini-Fuse Description 40 Amp Green — Power Folding Seat 30 Amp Pink — Power Liftgate Module 30 Amp Pink — Rear Door Module 25 Amp Natural — Driver Door Node 25 Amp Natural —...
Page 656 654 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description 60 Amp Yellow — Ignition Off Draw (IOD) – Main 40 Amp Green — Rear Window Defogger 40 Amp Green — Front Blower 40 Amp Green — Starter Solenoid 20 Amp Blue —...
Page 657 MAINTAINING YOUR VEHICLE 655 Cavity Cartridge Fuse Mini-Fuse Description — 20 Amp Yellow Power Outlet #1 (ACC), Rain Sensor, Cigar Lighter (Instrument Panel or with Console Rear) — 20 Amp Yellow Power Outlet #2 (BATT/ACC SELECT) – Cen- ter Seat or with Console Rear —...
Page 658 656 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description — 20 Amp Yellow Rear View Mirror, Instrument Cluster, Multi- Function Control Switch, Tire Pressure Moni- tor, Glow Plug Module – If Equipped — 10 Amp Red Airbag Module/Occupant Classification Module —...
Page 659 MAINTAINING YOUR VEHICLE 657 Cavity Cartridge Fuse Mini-Fuse Description — 10 Amp Red Power Mirror Switch, Driver Window Switch — 10 Amp Red Wireless Control Module, Keyless Entry Module — 10 Amp Red Powertrain, Transmission Control Module — 10 Amp Red Occupant Classification Module —...
Page 660: Vehicle Storage
658 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description — 10 Amp Red Antilock Brakes, Stability Control, Stop Lamp, Fuel Pump — 25 Amp Natural Door Lock/Unlock Motors, Liftgate Lock/ Unlock Motors • Or, disconnect the negative cable from the battery. The power windows are fused by a 25 Amp circuit breaker located in the Totally Integrated Power Module.
Page 661: Replacement Bulbs
MAINTAINING YOUR VEHICLE 659 REPLACEMENT BULBS Bulb Number Removable Console Interior Bulbs Lamp – If Equipped Bulb Number Visor Vanity Lamps 6501966 Center & Rear Dome NOTE: For lighted switches, see your authorized dealer Lamp for replacement instructions. Center & Rear Reading Lamps Exterior Bulbs Front Door Courtesy...
Page 662: Bulb Replacement
660 MAINTAINING YOUR VEHICLE High Intensity Discharge Headlamps (HID) — If Bulb Number Equipped Rear Turn Signal Lamp 3757A The headlamps are a type of high voltage discharge tube. Rear Tail, Stop, and Side LED (Serviced at Autho- High voltage can remain in the circuit even with the Marker Lamp rized Dealer) headlamp switch off and the key removed.
Page 663: Quad Headlamps
MAINTAINING YOUR VEHICLE 661 NOTE: On vehicles equipped with High Intensity Dis- CAUTION! charge (HID) headlamps, when the headlamps are turned on, there is a blue hue to the lamps. This dimin- Do not touch the new bulb with your fingers. Oil ishes and becomes more white after approximately 10 contamination will severely shorten bulb life.
Page 664: Front Side Marker Lamp
662 MAINTAINING YOUR VEHICLE Front Side Marker Lamp Front Fog Lamp 1. Raise the hood to access the rear of the headlamp NOTE: Access to the fog lamp bulb is from the rear of the housing. fascia. On the left rear side of the fascia, remove the push pin and lower the hinged access door on the air dam.
Page 665: Rear Turn Signal And Backup Lamp
MAINTAINING YOUR VEHICLE 663 2. Disconnect wire harness from the bulb. 3. Reconnect the wiring harness to the new bulb and reinstall the bulb by twisting clockwise. Rear Turn Signal And Backup Lamp 1. Raise the liftgate. 2. Remove the tail lamp assembly by removing the two screws from the inboard side.
Page 666: Center High-Mounted Stop Lamp (Chmsl)
664 MAINTAINING YOUR VEHICLE 3. Twist the socket and remove it from the lamp assem- License Lamp bly. The license plate lamp is located under the tailgate light bar and above the license plate. 4. Pull the bulb to remove it from the socket. 1.
Page 667: Fluid Capacities
Engine Coolant 10 Year/ 150,000 Mile Formula or equiva- lent) meeting the requirements of Chrysler Material Standard MS-12106. * Includes heater and coolant recovery bottle filled to MAX level. Add 2.9 Qts (2.8 L) if equipped with a rear heater.
Page 668: Fluids, Lubricants And Genuine Parts
Engine Oil We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the require- ments of Chrysler Material Standard MS-6395 such as MOPAR®, Pennzoil®, and Shell Helix®. Refer to your engine oil filler cap for correct SAE grade. Engine Oil Filter We recommend you use MOPAR®...
Page 669: Chassis
MAINTAINING YOUR VEHICLE 667 Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Use Only ATF+4® Automatic Transmission Fluid. Fail- ure to use ATF+4® fluid may affect the function or performance of your transmission. We recommend MOPAR® ATF+4® Fluid. Brake Master Cylinder We recommend you use MOPAR®...
Page 671: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS ▫ Maintenance Chart ....672 MAINTENANCE SCHEDULE ... . .670...
Page 672 670 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE than your authorized dealer, the message can be reset by referring to the steps described under “Electronic Vehicle Your vehicle is equipped with an automatic oil change Information Center (EVIC)/Oil Change Required” in indicator system. The oil change indicator system will “Understanding Your Instrument Panel”...
Page 673 MAINTENANCE SCHEDULES 671 • Check tire pressure and look for unusual wear or At Every Oil Change Interval As Indicated By Oil damage. Rotate tires at the first sign of irregular wear, Change Indicator System: even if it occurs before the oil indicator system turns on. •...
Page 674 672 MAINTENANCE SCHEDULES Maintenance Chart Refer to the Maintenance Schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, boot seals, and replace if necessary.
Page 675 MAINTENANCE SCHEDULES 673 Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Maintenance Replace engine air filter. Replace cabin/air conditioning filter. Replace spark plugs (3.6L engine). ** Flush and replace the engine cool- ant at 10 years or 150,000 miles (240,000 km) whichever comes first.
Page 676 674 MAINTENANCE SCHEDULES Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Change automatic transmission fluid and filter if using your ve- hicle for any of the following: po- lice, taxi, fleet, or frequent trailer towing. Change automatic transmission fluid and filter.
Page 677 MAINTENANCE SCHEDULES 675 WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 679 IF YOU NEED ASSISTANCE ....679 REPORTING SAFETY DEFECTS ... .683 ▫ Chrysler Group LLC Customer Center..680 ▫ In The 50 United States And Washington, D.C..
Page 680 678 IF YOU NEED CONSUMER ASSISTANCE ▫ Traction Grades ..... . .685 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES ....685 ▫...
Page 681: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 679 SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 682: Chrysler Group Llc Customer Center
• Vehicle delivery date and mileage This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer service manager first. Most matters can be re- solved with this process.
Page 683: In Mexico Contact
IF YOU NEED CONSUMER ASSISTANCE 681 In Mexico Contact: Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered Av. Prolongacion Paseo de la Reforma, 1240 by Bell Canada. For TTY teletypewriter users, dial 711 Sante Fe C.P.
Page 684: Warranty Information
See the Warranty Information Booklet, located on the the ownership experience. You will be pleased with their DVD, for the terms and provisions of Chrysler Group sincere efforts to resolve any warranty issues or related LLC warranties applicable to this vehicle and market.
Page 685: Mopar® Parts
IF YOU NEED CONSUMER ASSISTANCE 683 MOPAR® PARTS campaign. However, NHTSA cannot become involved in individual problems between you, your authorized MOPAR® fluids, lubricants, parts, and accessories are dealer, and the manufacturer. available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle To contact NHTSA, you may either call the Auto Safety operating at its best.
Page 686: Publication Order Forms
Chrysler Group LLC vehicles. ing, servicing, and repairing Chrysler Group LLC ve- Included are starting, operating, emergency and mainte- hicles.
Page 687: Department Of Transportation Uniform Tire Quality Grades
IF YOU NEED CONSUMER ASSISTANCE 685 Call toll free at: Treadwear • 1–800–890–4038 (U.S.) The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled • 1–800–387–1143 (Canada) conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded Visit us on the Worldwide Web at:...
Page 688: Temperature Grades
686 IF YOU NEED CONSUMER ASSISTANCE Vehicle Safety Standard No. 109. Grades B and A repre- WARNING! sent higher levels of performance on the laboratory test wheel, than the minimum required by law. The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not WARNING! include acceleration, cornering, hydroplaning, or...
Page 689 INDEX...
Page 690 688 INDEX Adding Engine Coolant (Antifreeze) ... .636 Air Conditioning System, Zone Control..443 Adding Fuel ......549 Air Pressure, Tires.
Page 691 INDEX 689 Fluid and Filter Changes ....644 Brake System ......640 Fluid Change .
Page 692 690 INDEX Car Washes ......645 Compact Spare Tire ......523 Cellular Phone .
Page 693 INDEX 691 Disposal of Used Coolant ....639 Oil (Engine) ......623 Drain, Flush, and Refill .
Page 694 692 INDEX Electronic Speed Control (Cruise Control) ..243 Fails to Start ......471 Electronic Stability Control (ESC) .
Page 695 INDEX 693 FCC General Information (Sentry Key) ...18 Floor Console ......294 Filler Location Fuel .
Page 696 694 INDEX Ethanol ......541 Gas Cap (Fuel Filler Cap) ....549 Filler Cap (Gas Cap) .
Page 697 INDEX 695 Hazard Hood Release ......224 Driving Through Flowing, Rising, or Shallow Hook, Coat......293 Standing Water .
Page 698 696 INDEX iPod®/USB/MP3 Control Light Bulbs......128 Bluetooth® Streaming Audio ....186 Lights .
Page 699 INDEX 697 Headlights On Reminder ....228 Side Marker ......662 High Beam Indicator .
Page 700 698 INDEX Malfunction Indicator Light (Check Engine)..326 Monitor, Tire Pressure System ....531 Manual, Service ......684 Mopar Parts .
Page 701 INDEX 699 Materials Added to ..... .625 Pets, Transporting ......120 Recommendation .
Page 702 700 INDEX Programmable Electronic Features ... . .353 Remote Sound System (Radio) Controls ..441 Radial Ply Tires ......520 Remote Starting System.
Page 703 INDEX 701 Satellite Radio Antenna .....383 Reclining ......196 Schedule, Maintenance .
Page 704 702 INDEX Spare Tire.......523 Storage, Vehicle......658 Speed Control (Cruise Control).
Page 705 INDEX 703 Air Pressure ......517 Spare Tire ......587 Chains .
Page 706 704 INDEX Cooling System Tips .....566 Uconnect® Hitches ......557 Advanced Phone Connectivity .
Page 707 INDEX 705 Universal Transmitter ..... .264 Warnings and Cautions..... . .6 Unleaded Gasoline .
Page 708 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s The antenna cable should be as short as practical and routed away electronic system to provide immunity to radio frequency signals. from the vehicle wiring when possible. Use only fully shielded Mobile two-way radios and telephone equipment must be installed coaxial cable.
Page 709 Chrysler Group LLC 14Y531-126-AC Printed in U.S.A. Third Edition 14C482-126-AA First Edition Printed in U.S.A.

This manual is also suitable for:

2014 town & country

Chrysler 2014 Town&Country Owner's Manual

Table of Contents

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Quick Links

Chapters

Related Manuals for Chrysler 2014 Town&Country Chrysler

Summary of Contents for Chrysler 2014 Town&Country Chrysler