Advertisement
Control panel
Sleeve
A
B
INSTALLATION
The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
In dash-mounting
Rubber cushion
Do the required electrical
connections.
When using the optional stay
Fire wall
*
Washer (ø5)
Lock nut (M5)
Dashboard
Screw (option)
Mounting bolt—M4 × 5 mm
(M4 × 1/4"); M5 × 12.5 mm
(M5 × 1/2")
ELECTRICAL CONNECTIONS
Typical connections
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this
unit. The leads of the power cord and those of the connector from the car body may be different in color.
1
Connect the colored leads of the power cord in the order specified in the illustration below.
2
Connect the antenna cord.
3
Finally connect the wiring harness to the unit.
Rear line out
Rear ground terminal
Antenna
terminal
Black
Connect only the front speakers if your
speaker system is two-speaker system.
White with black stripe
Yellow *
Front speaker (left)
White
Gray with black stripe
Red
Front speaker (right)
Gray
Blue with white
Green with black stripe
stripe
Rear speaker (left)
Green
Purple with black stripe
Rear speaker (right)
Purple
Parts list for installation and connection
Trim plate
C
When you stand the unit,
be careful not to damage
*
the fuse on the rear.
Mounting bolt—M4 × 5 mm
(M4 × 1/4"); M5 × 12.5 mm
*
(M5 × 1/2")
Bend the appropriate tabs
to hold the sleeve firmly
in place.
* Not supplied for this unit.
Stay (option)
* Not supplied for this unit.
*
Install the unit at an angle of
*
less than 30˚.
15 A fuse
To the metallic body
or chassis of the car
To a live terminal in the
fuse block connecting to the
2
car battery (bypassing the
ignition switch) (constant
12 V)
Fuse block
To an accessory terminal in
the fuse block
To the remote lead of other
equipment or automatic antenna if
any (200 mA max.)
Power cord
D
Before removing the unit, release the rear section.
When installing the unit without using the sleeve
In a Toyota car for example, first remove the car radio and install the unit in its place.
Flat type screws—M5 × 8 mm (M5 × 3/8")*
Bracket*
Flat type screws
—M5 × 8 mm (M5 × 3/8")*
Pocket
Bracket*
Connecting the external amplifier or subwoofer
Set "L/O MODE" to "REAR"
(See "General settings—PSM.")
You can connect a power amplifier for
rear speakers.
JVC Amplifier
Rear
speakers
Ignition switch
Set "L/O MODE" to "WOOFER"
(See "General settings—PSM.")
You can also connect a subwoofer to
the REAR LINE OUT terminals.
JVC Amplifier
Subwoofer
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be
seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.
4 – EN
Handles
Remote controller
E
F
Removing the unit
* Not supplied for this unit.
Remote lead
Remote lead (blue with white stripe)
To the remote lead of other equipment
or automatic antenna if any
Right
Left
*
1
Not supplied for this unit.
*
2
Before checking the operation of this unit prior to installation, this
lead must be connected, otherwise the power cannot be turned on.
or
*
3
Firmly attach the ground wire to the metallic body or to the chassis
of the car—to the place uncoated with paint (if coated with paint,
remove the paint before attaching the wire). Failure to do so may
cause damage to the unit.
*
4
Signal cord (not supplied for this unit)
Battery
G
Y-connector *
1
Front speakers
Hide quick links:
Advertisement
