Table of Contents
Advertisement
USING YOUR GARAGE DOOR OPENER
Your opener can be activated by any of the following devices:
• The LCD Motion Detecting Control. Hold the PUSH BAR
down until door starts to move.
• The Outside Keyswitch or Keyless Entry System (if you
have installed either of these accessories).
• The Remote Control Transmitter. Hold the push button
down until the door starts to move.
Opening the Door Manually: Door should be fully closed if
possible. Weak or broken springs could allow an open
door to fall rapidly. Property damage or serious personal
injury could result.
The door can be opened manually by pulling the release
handle down. To reconnect the door, pull the release handle
down and toward the opener.
Do not use the manual release handle to pull the door
opener or closed. When the Opener is Activated by
Remote Control or LCD Motion Detecting Control:
1. If open, the door will close. If closed, the door will open.
2. If closing, the door will stop.
3. If opening, the door will stop (allowing space for entry and
exit of pets and for fresh air).
4. If the door has been stopped in a partially open or closed
position, it will reverse direction.
5. If an obstruction is encountered while closing, the door will
reverse.
6. If an obstruction is encountered while opening, the door will
reverse and stop.
7. The optional Protector System™ uses an invisible beam
which, when broken by an obstruction, causes a closing
door to open and prevents an open door from closing. It is
STRONGLY RECOMMENDED for homeowners with young
children.
The opener lights will turn on under the following conditions:
when the opener is initially plugged in; when power is restored
after interruption; when the opener is activated.
They will turn off automatically after 2-1/2 minutes or provide
constant light when the Light feature on the LCD Motion
Detecting Control is activated. Bulb size is E27. Bulb power is
40 watts maximum.
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
or
THE REMOTE CONTROL BATTERY
To replace battery, use a screwdriver
blade to pry open the case as shown.
Insert battery positive side up.
Dispose of old battery properly.
Carefully
Remove Battery
30
SPECIFICATIONS
Input Voltage.....
Max. Pull Force
Rated Load .......
Standby Power .
Max. Door Mass
Max. Door Area
Motor
Type..................
Drive Mechanism
Drive .................
Length of Travel
Travel Rate .......
Lamp.................
Door Linkage ....
Safety
Personal ...........
Electronic..........
Electrical ...........
Limit Device ......
detector.
Limit Adjustment
Start Circuit.......
Dimensions
Length (Overall)
Headroom Required
Hanging Weight
Receiver
Memory Registers
Operating Frequency
SPECIAL NOTE: Chamberlain strongly recommends
that The Protector System
on all garage door openers.
CARE OF YOUR OPENER
MAINTENANCE SCHEDULE
Once a Month
• Manually operate door. If it is unbalanced or binding,
call a qualified door technician.
• Check to be sure door opens & closes fully. Adjust
limits and/or force if necessary, refer pages 20 and 21.
• Repeat the safety reverse test. Make any necessary
adjustments, refer page 22.
Once a Year
• Oil door rollers, bearings and hinges. The opener
does not require additional lubrication. Do not grease
the door tracks.
230-240 VAC, 50Hz
800N
8Nm
2.9W
130kg (spring balanced)
16.5m
2
DC gearmotor permanent
lubrication
Belt with two-piece trolley on
steel rail.
Adjustable to 3m
127-178mm per second
On when door starts, off 2-1/2
minutes after stop.
Adjustable door arm. Pull cord
trolley release.
Push button stop in UP and
DOWN direction. Automatic
safety reverse in UP and
DOWN direction.
Automatic force adjustment
Transformer overload protector
and low voltage push button
wiring.
Optical RPM/Passpoint
Electronic, Semi and Fully
Automatic.
Low voltage push button circuit.
3.2m for standard 2.3m rail
30mm
14.5 kg
64
433.92MHz
(IR Beams) be installed
TM
Hide quick links:
Advertisement
Table of Contents
