Table of Contents
Advertisement
www.chamberlainanz.com
MT5580P
Sectional and Tilt Garage Door Opener
Installation and Operating Instructions
Owners Copy: Please keep these instructions for future reference
This manual contains IMPORTANT SAFETY information.
DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THOROUGHLY.
N2966
N2966
N2966
N2966
Advertisement
Table of Contents
Related Manuals for Chamberlain merlin MT5580P
Summary of Contents for Chamberlain merlin MT5580P
- Page 1 www.chamberlainanz.com MT5580P Sectional and Tilt Garage Door Opener Installation and Operating Instructions Owners Copy: Please keep these instructions for future reference This manual contains IMPORTANT SAFETY information. DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THOROUGHLY. N2966 N2966 N2966 N2966...
-
Page 2: Table Of Contents
START BY READING THESE IMPORTANT SAFETY INSTRUCTIONS WARNING • Failure to comply with the following instructions may result in serious personal injury or property damage. • Read and follow all instructions carefully. • The garage door opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the instructions in this manual. -
Page 3: Door Types
DOOR TYPES A. One-piece door with horizontal track only B. Sectional door with curved track C. One-piece door without track To suit spring balanced doors up to 15.5m TOOLS REQUIRED 4mm hex 10mm, 8mm, head driver 4,5mm, 4mm 11mm, 13mm HARDWARE PROVIDED Vibration Isolator: (a) Vibration isolator (2) -
Page 4: Chain
HARDWARE PROVIDED (1) MT5580 opener (2) Angled door arm (3) Door mounting bracket (4) Straight door arm (5) Header bracket (6) Stop collar and grub screw (7) Pole kit adaptor (8) Trolley assembly (9) Idler (10) Chain and joiner 3m Chain Pack and Joiner Pole Adaptor Kit POLE OPTIONS 7527SP1 (optional accessory) -
Page 5: Before You Begin
BEFORE YOU BEGIN 1. Look at the wall or ceiling above the garage door. The header bracket must be securely fastened to structural supports. 2. Do you have a finished ceiling in your garage? If so, a support bracket and additional fastening hardware (not supplied) may be required. - Page 6 INSTALL THE TROLLEY AND IDLER PULLEY Slide the trolley assembly (1) onto the pole (3) taking note of the door direction arrow (fig 1). The trolley should be located midway along the pole. fig 1 Insert the pole (3) into the idler pulley (2) end as illustrated.
- Page 7 INSTALL THE CHAIN Fitting the Chain: Wrap the chain around the idler pulley (1) and desired drive sprocket (as illustrated in fig 1 and 2 below), ensuring the chain passes through the trolley assembly (3). NOTE: Locate the chain connector (2) as illustrated above approximately 300mm from the Idler pulley.
-
Page 8: Installation
INSTALLATION SECTION Wear protective goggles when working overhead to protect your eyes from injury. Disengage all existing garage door locks to avoid damage to the garage door. To avoid serious personal injury from entanglement, remove all ropes connected to the garage door before installing the opener. - Page 9 ATTACH POLE ASSEMBLY TO HEADER BRACKET Position opener on garage floor below the header bracket. Use packing material to protect the cover. NOTE: To enable the Pole to clear sectional door springs, it may be necessary to lift opener onto a tem- porary support.
- Page 10 INSTALL VIBRATION ISOLATORS Fit the vibration isolators as indicated to help eliminate vibration often transmitted through the mounting surface. Vibration Isolator Washer HANG THE OPENER The opener must be securely fastened to a structural support of the garage. Three representative installations are shown. Yours may be different. Hanging brackets (1) should be angled (Figure A) to provide rigid support.
- Page 11 ATTACH MANUAL RELEASE ROPE & HANDLE Thread one end of rope (1) through hole in top of red handle so "NOTICE" reads right side up as shown (3). Secure with an overhand knot (2). Knot should be at least 25mm (1") from end of the rope to prevent slipping.
-
Page 12: Carriage
FASTEN DOOR BRACKET Sectional and One-Piece Door Installation Procedure: Door bracket (1) has left and right side fastening holes. If your installation requires top and bottom fastening holes use both the door bracket and door bracket plate (2) as shown. 1. - Page 13 CONNECT DOOR ARM FOR (SECTIONAL DOORS) Figure 1 Trolley Pulley Make sure garage door is fully closed. Pull the emer- gency release handle to disengage the trolley. Slide the trolley assembly back 200mm from the idler pul- ley. Ring Clevis Pin Fastener Figure 1.
-
Page 14: Adjustment
ADJUSTMENT SECTION ADJUST THE TRAVEL LIMITS Limit adjustment settings regulate the point at which the Without a properly installed safety reversal system, persons door will stop whilst moving up or down. (particularly small children) could be SERIOUSLY INJURED or To set the limits: KILLED by a closing garage door. -
Page 15: Safety Reverse System
TEST THE SAFETY REVERSE SYSTEM The safety reverse system test is important. The garage door must reverse on contact with a 40mm obstacle laid flat on the floor. Failure to properly adjust opener may result in serious personal injury from a closing garage door. Repeat test once a month and adjust as needed. Procedure: Place a 40mm obstacle (1) laid flat on the floor under the garage door. -
Page 16: Wired Door Controls
INSTALL WIRED DOOR CONTROLS (optional accessory) Locate wired door controls where the garage door is visible, away from door and door hardware, out of the reach of children and at a height of at least 1.5m. Serious personal injury from a moving garage door may result from misuse of opener. Do not allow children to operate the wired door controls or transmitters. -
Page 17: Wireless Programming
WIRELESS PROGRAMMING (OPTIONAL ACCESSORY) Activate the opener only when door is in full view, free of obstruction and properly adjusted. No one should enter or leave garage while door is in motion. Do not allow children to operate push button(s) or transmitter(s). -
Page 18: Special Features
INSTALLING YOUR CM128 WIRELESS WALL BUTTON INSTALL: Carefully pry open the CM128 and locate the two screw for mounting. To attach to the wall, use the two screws and wall anchors provided, if mount to plaster wall (If using a recessed wall box do not use anchors). NOTE: Tightening the wall mount screws will reduce clearance between bracket and wall. -
Page 19: Accessories
On when door starts, off Headroom required: 60mm 2-1/2 minutes after stop. Hanging Weight: 12.5kg Door Linkage: Adjustable door arm. Pull cord Receiver Memory trolley release. Registers: SPECIAL NOTE: Chamberlain strongly recommends that the Protector System be installed on all garage door openers. -
Page 20: Operation Of Your Opener
OPERATION OF YOUR OPENER Your opener can be activated by any of the following devices: • Wireless Wall Button (CM128). Press button down until door starts to move. • The Outside Keyswitch or Keyless Entry System (if you have installed either of these accessories). •... -
Page 21: Replacement Parts
REPLACEMENT PARTS 178B0086B 091B0019 012B0905 178B0034B 012B0906 083A0011-1 171A0828 002A0958 035A0070 001A6698 ADR10068 012B0921 7527SP1 Segmented Pole Pack 001A6793-1 001A4208-2 001A4627 001A6829... -
Page 22: Replacement Parts
REPLACEMENT PARTS If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid hazard. 041A3261-1 (Dual Sprocket) 041A5833 026B0072 175B0174 041B4375 041A5813 108D0068-1 041A5831-10 041A5809 030B0415 081C0253 041C4398A 041A5432 041A5525-71... -
Page 23: Troubleshooting
Troubleshooting 8. Door stops but doesn't close completely: Review Limit Adjustment section. 1. Opener doesn't operate from either door control or trans- Repeat safety reverse test after any adjustment of door arm mitter: length, close force or down limit. • Does the opener have electric power? Plug lamp into outlet. If 9. -
Page 24: Warranty
Zealand Limited (Seller) warrants to the original purchas- law or contract or for negligence, exceed the cost of repairing er of the Merlin MT5580P Garage Door Opener (Unit) that or replacing the Unit or refunding the purchase price of the it is free from defects in material and/or workmanship for Unit.