JVC GR-DZ7 Instructions Manual page 49

Although Snapshot is attempted, flash does not
take place.
The subject is too bright with the flash set to " ±0A" or
"C ±0A".
HSet the flash mode to "ON". (
If blinks, the flash is being charged.
HIt can take up to 10 seconds to charge the flash.
The camcorder is in the Record mode.
HSet the camcorder in the Record-Standby mode.
( pg. 33, 35)
Although a Snapshot is taken with the flash, Red-
Eye Reduction does not take place.
The subject does not look straight toward the flash.
The subject does not look at the first flash, which is an
important part of Red-Eye Reduction.
HThe subject should look straight toward the flash,
especially the first flash. If the subject does not see the first
flash, it will be difficult for Red-Eye Reduction to take place.
( pg. 33)
The camcorder is too far from the subject.
HThe flash is effective for subjects at a distance of approx.
0.7 m (2 ft) to 2 m (6.5 ft) from the camcorder. (
Other problems
The POWER/CHARGE lamp on the camcorder does
not light during charging.
Charging is difficult in places subject to extremely high/low
temperatures.
HTo protect the battery, it is recommended to charge it in
places with a temperature of 10°C to 35°C (50°F to 95°F).
( pg. 52)
The battery pack is not attached firmly.
HDetach the battery pack once again and re-attach it firmly.
( pg. 12)
"SET DATE/TIME!" appears.
The built-in clock's battery has run out.
HConsult your nearest JVC dealer for replacement.
The previously set date/time is erased.
Files stored in the memory card cannot be deleted.
Files stored in the memory card are protected.
HRemove protection from the files stored in the memory
card and delete them. (
When the image is printed from the printer, a black
bar appears at the bottom of the screen.
This is not a malfunction.
HBy recording with "DIS" activated (
be avoided.
pg. 29)
pg. 33)
pg. 27)
pg. 29, 30) this can
When the camcorder is connected via the DV
connector, the camcorder does not operate.
The DV cable was plugged/unplugged with power turned
on.
HTurn the camcorder's power off and on again, then operate
it.
Images on the LCD monitor appear dark or whitish.
In places subject to low temperature, images become dark
due to the characteristics of the LCD monitor. This is not a
malfunction.
HAdjust the brightness and angle of the LCD monitor.
( pg. 15, 17)
When the LCD monitor's fluorescent light reaches the end
of its service life, images on the LCD monitor become dark.
HConsult your nearest JVC dealer.
Colored bright spots appear all over the LCD
monitor or the viewfinder.
The LCD monitor and the viewfinder are made with high-
precision technology. However, black spots or bright spots
of light (red, green or blue) may appear constantly on the
LCD monitor or the viewfinder. These spots are not
recorded on the tape. This is not due to any defect of the
unit. (Effective dots: more than 99.99 %)
The cassette will not load properly.
The battery's charge is low.
HInstall a fully charged battery. (
The memory card cannot be removed from the
camcorder.
HPush in the memory card a few more times. (
The memory card lock switch is set to the lock position.
HSlide the memory card switch to the unlock position.
( pg. 16)
Picture does not appear on the LCD monitor.
The viewfinder is pulled out and "PRIORITY" is set to
"FINDER".
HPush the viewfinder back in or set "PRIORITY" to "LCD".
( pg. 17, 29, 31)
The LCD monitor's brightness setting is too dark.
HAdjust the brightness of the LCD monitor. (
HIf the monitor is tilted upward 180 degrees, open the
monitor fully. ( pg. 17)
An error indication (E01 – E04 or E06) appears.
A malfunction of some kind has occured. In this case the
camcorder's functions become unusable.
H
pg. 51
The remote control does not work.
"REMOTE" is set to "OFF".
HSet "REMOTE" to "ON". (
The remote control does not point at the remote sensor.
HPoint at the remote sensor. (
The remote control batteries are exhausted.
HReplace the batteries with fresh ones. (
TROUBLESHOOTING
EN
pg. 12)
pg. 16)
pg. 15)
pg. 29, 31)
pg. 21)
pg. 21)
49