Sylvania SRT2227X Service Manual page 15

3-1. Setting for 7F and FRENCH
data Values
General
1. Enter the Service mode. (See page 5-1)
2. Press " VOL p " button on the Service remote con-
trol unit. Display changes " C/D ", " 7F ", " FRENCH
", " ACCESS CODE ", " STEREO ", " VIDEO TONE
", " FM-MODE ", and " V-OUT " cyclically when "
VOL p " button is pressed.
7F
1. Press " VOL p " button on the Service remote con-
trol unit. Then select 7F display.
2. Press " CH o / p " buttons on the Service remote
control unit. Then choose 7F=FF.
FRENCH
1. Press " VOL p " button on the Service remote con-
trol unit. Then select FRENCH display.
2. Press " CH o / p " buttons on the Service remote
control unit. Then choose FRENCH=OFF.
ACCESS CODE ---- set to ON
VIDEO TONE ---- set to ON
FM-MODE ---- set to OFF
V-OUT ---- set to OFF
STEREO ---- set to ON
Note: C/D and VCO data values do not need to be
adjusted at this moment.
3-2. Setting for CONTRAST,
COLOR, TINT, V-TINT and
SHARP data Values
General
1. Enter the Service mode. (See page 5-1)
2. Press " MENU " button on the Service remote control
unit. Display changes " BRIGHT ", " CONTRAST ",
" COLOR ", " TINT ", " V-TINT " and " SHARP "
cyclically when " MENU " button is pressed.
CONTRAST (CNT)
1. Press " MENU " button on the Service remote con-
trol unit. Then select " CONTRAST " (CNT) display.
2. Press " CH o / p " buttons on the Service remote
control unit so that the value of " CONTRAST "
(CNT) becomes 84.
COLOR (CLR)
1. Press " MENU " button on the Service remote con-
trol unit. Then select " COLOR " (CLR) display.
2. Press " CH o / p " buttons on the Service remote
control unit so that the value of " COLOR " (CLR)
becomes 58.
TINT (TNT)
1. Press " MENU " button on the Service remote con-
trol unit. Then select " TINT " (TNT) display.
2. Press " CH o / p " buttons on the Service remote
control unit so that the value of " TINT " (TNT) be-
comes 62.
V-TINT (V-TNT)
1. Press " MENU " button on the Service remote con-
trol unit. Then select " V-TINT " (V-TNT) display.
2. Press " CH o / p " buttons on the Service remote
control unit so that the value of " V-TINT " (V-TNT)
becomes 59.
SHARP (SHARP)
1. Press " MENU " button on the Service remote con-
trol unit. Then select " SHARP " (SHARP) display.
2. Press " CH o / p " buttons on the Service remote
control unit so that the value of " SHARP "
(SHARP) becomes 47.
Note: BRIGHT data value does not need to be adjust-
ed at this moment.
4. Black Level Adjustment
Purpose: Set Black Level
Symptom of Misadjustment: If black level is incor-
rect, Proper brightness can not be obtained by adjust-
ing the Brightness Control.
1. Enter the Service mode. (See page 5-1).
2. Press " MENU " button on the Service remote con-
trol unit and select " BRT "mode. (Display changes
" BRT ", " CNT ", " CLR ", " TNT ", " V-TINT ", and
" SHRAP " cyclically when MENU button is
pressed).
3. Press " CH o / p " buttons on the Service remote
control unit so that the value of " BRT " becomes
128.
4. Turn the power off and on again. (Main power but-
ton on the TV unit.)
5-2 L6600EA