Advertisement
Revo Burst™
operating Modes: The Revo Burst can operate in three dif-
ferent modes. In each mode you can run the fixture as a stand
alone fixture or in a master/slave confiugration. This next section
will detail the differences in the operating modes.
• Sound Active mode -
The fixture will react to sound, chasing through the built-in programs.
• Show mode -
Choose 1 of 12 show modes to run.
• DMX control mode -
This function will allow you to control each individual fixtures traits
with a standard DMX-512 controller such as the Elation
Designer.
™
Master-Slave Operation
This function will allow you to link up to 16
units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The first unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. On the Master unit find your desired show and set that show by
pressiing the ENTER button.
3. On the slave units
tap the MENU button until "SLND" is dis-
played, and Press ENTER.
4. The slave units will now follow the Master unit.
Universal DMX Control:
universal DMX-512 controller to control the chases and patterns, dim-
mer and strobe. A DMX controller allows you to create unique pro-
grams tailored to your individual needs.
1. The Revo Burst can either be a 4 or 10 Channel fixture. See page
14 for detailed description of the DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
American DJ Supply
- www.americandj.com - Revo Burst™ User Manual Page 12
©
®
Operating Instructions
This function allows you to use a Elation
Revo Burst™
SHND: SH 0 - 12
show mode to run properly, make sure sound active mode is
off.
1. Tap the MENU button until "SHND" is displayed, press ENTER.
2. "Sh X" will now be displayed, "X" representing a number
between 0-10. Programs 1-12 are factory programs, while "Sh
0" is random mode. Press the UP or DOWN buttons to find your
desired show and press the ENTER, then press and hold the
MENU button for at least 3 seconds to confirm.
Show
SOUN -
®
Sound Active mode.
1. Tap the MENU button until "SOUN" is displayed, press ENTER.
2. The display will show either "ON" or "OFF". Press the UP or
DOWN buttons to select "ON" to activate sound active mode, or
"OFF" to deactivate sound active mode.
3. Press the ENTER, and then press and hold the MENU button
for at least 3 seconds to confirm.
SENS
- Using this mode, you can set the sound sensitivity
level. 0 for least sensitive, 100 for more sensitive.
1. Tap the MENU button until "SENS" is displayed, press ENTER.
2. Using the UP or DOWN buttons adjust the sensivity level to your
desire.
3. When you found your desired level, press the ENTER, and then press
and hold the MENU button for at least 3 seconds to confirm.
®
BLND -
Blackout or Stand by mode.
1. Tap the MENU button until "BLND" is displayed, press ENTER.
Either Yes or No will be displayed.
2. To activate Blackout tap the UP or DOWN buttons until "Yes"
American DJ Supply
©
- Show modes 0-12 (Factory programs). For
- www.americandj.com - Revo Burst™ User Manual Page 9
®
System Menu
Advertisement
