1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Laptop
  5. STREAMLINE-S 10
  6. Maintenance manual

Toshiba STREAMLINE-S 10 Maintenance Manual

Personal computer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Toshiba Personal Computer
STREAMLINE-S 10
Maintenance Manual
TOSHIBA CORPORATION
[CONFIDENTIAL]

Advertisement

Table of Contents
loading

Related Manuals for Toshiba STREAMLINE-S 10

Summary of Contents for Toshiba STREAMLINE-S 10

  • Page 1 Toshiba Personal Computer STREAMLINE-S 10 Maintenance Manual TOSHIBA CORPORATION [CONFIDENTIAL]...
  • Page 2 © 2010 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein.
  • Page 3 NOTE: “Note” contains general information that relates to your safe maintenance service. Improper repair of the computer may result in safety hazards. Toshiba requires service technicians and authorized dealers or service providers to ensure the following safety precautions are adhered to strictly.
  • Page 4 The manual is divided into the following parts: Chapter 1 Hardware Overview describes the SATELLITE T210/T215/PRO T210/T215/PORTEGE T210 MAINTENANCE MANUALL Series system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service.
  • Page 5 Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus (+) sign. For example, Ctrl + Pause (Break) means you must hold down Ctrl and at the same time press Pause (Break). If three keys are used, hold down the first two and at the same time press the third.

  • Page 6: Table Of Contents

    Table of Contents Chapter 1 Features................Error! Bookmark not defined. 9.5mm (2.5-inch) HDD............Error! Bookmark not defined. Power Supply..............Error! Bookmark not defined. Batteries ................Error! Bookmark not defined. 1.4.1 Main Battery............Error! Bookmark not defined. 1.4.2 Battery Charging Control........Error! Bookmark not defined. 1.4.3 RTC Battery ............Error! Bookmark not defined. Chapter 2 Troubleshooting Introduction ....................3 Troubleshooting Flowchart....................4...
  • Page 7 RTC Test..........................26 3.15 G-sensor Test........................28 3.16 HDD Test………………...………..............……..31 3.17 Read DMI Test………….……..............……..………...34 3.18 Write DMI Test..………… ................…...……….35 3.19 Toshiba Logo Set………….…....................37 3.20 Dynabook Logo Set….… ..................….…39 3.21 TP Type R/W Test….….….…… .................….…….41 3.22 EE-PROM SETTING…….…......……………………….……...……….…..44 ONFIDENTIAL] SATELLITE T210/T215/PRO T210/T215/PORTEGE T210 MAINTENANCE MANUALL...
  • Page 8 Chapter 4 General................Error! Bookmark not defined. Safety Precautions..............Error! Bookmark not defined. Before You Begin ..............Error! Bookmark not defined. Disassembly Procedures ............Error! Bookmark not defined. Assembly Procedures............Error! Bookmark not defined. Tools and Equipment ............Error! Bookmark not defined. Screw Tightening Torque ..........Error! Bookmark not defined. Colors of Screw Shanks .............Error! Bookmark not defined.
  • Page 9 Installing the Touch Pad Assembly ........Error! Bookmark not defined. WLAN Card...............Error! Bookmark not defined. Removing the WLAN Card ..........Error! Bookmark not defined. Installing the WLAN Card..........Error! Bookmark not defined. 4.10 WWAN Card ..............Error! Bookmark not defined. Removing the WWAN Card..........Error! Bookmark not defined. Installing the WWAN Card ..........Error! Bookmark not defined.
  • Page 10 Removing the Speakers............Error! Bookmark not defined. Installing the Speakers ............Error! Bookmark not defined. 4.20 Thermal Module ..............Error! Bookmark not defined. Removing the Thermal Module .........Error! Bookmark not defined. Installing the Thermal Module...........Error! Bookmark not defined. 4.21 LCD Bezel .................Error! Bookmark not defined. Removing the LCD Bezel ..........Error! Bookmark not defined.
  • Page 11 Figure 2-11 2 in 1 card troubleshooting process ...............31 Figure 2-12 HDD troubleshooting process................33 Figure 2-13 CRT troubleshooting process ................35 Figure 2-14 LAN troubleshooting process ................37 Figure 2-15 MIC troubleshooting process.................39 Figure 2-16 3D sensor troubleshooting process .................41 Figure 2-17 3G troubleshooting process ..................43 Figure 4.1 Removing the battery pack........Error! Bookmark not defined.
  • Page 12 Figure 4.25 Removing the HDD board........Error! Bookmark not defined. Figure 4.26 Removing the Bluetooth module......Error! Bookmark not defined. Figure 4.27 Removing the RGB board ........Error! Bookmark not defined. Figure 4.28 Removing the display assembly .......Error! Bookmark not defined. Figure 4.29 Removing motherboard from logic lower assembly Error! Bookmark not defined. Figure 4.30 Installing the motherboard ........Error! Bookmark not defined.
  • Page 13 Appendix F Series Screw Torque List..................F-1 Appendix G Reliability......................G-1 ONFIDENTIAL] SATELLITE T210/T215/PRO T210/T215/PORTEGE T210 MAINTENANCE MANUALL xiii...
  • Page 14 Chapter 1 Hardware Overview...
  • Page 15 1 Hardware Overview Chapter 1 Contents Features ........................1-1 9.5mm (2.5-inch) HDD ..................1-10 Power Supply ....................... 1-11 Batteries........................ 1-13 1.4.1 Main Battery ..................1-13 1.4.2 Battery Charging Control ..............1-13 1.4.3 RTC Battery..................1-14 Satellite T210/T215/Pro T210/T215/PORTEGE T210 Maintenance Manual 1-ii...
  • Page 16 1 Hardware Overview Figures Figure 1-1A ID Parts Description Placement Part A............1-6 Figure 1-2 SATA HDD ....................1-10 Tables Table 1-1 HDD Specifications ..................1-10 Table 1-2 Quick/Normal Charging Time ..............1-13 Satellite T210/T215/Pro T210/T215/PORTEGE T210 Maintenance Manual 1-iii...

  • Page 18: Features

    Error! No text of specified style in document. Error! No text of specified style in document. Hardware Overview Features The Toshiba Satellite T210/T215/Pro T210/T215/PORTEGE T210 series portable personal computer is based on a Dual Core/Quad Core Processor, providing high-speed processing capabilities and advanced features. The computer employs a lithium ion battery that allows it to be battery-operated for a long period of time.
  • Page 19  HDMI V1.3 support (without CEC)  Keyboard (BTO) The computer is equipped with a Toshiba NB200 keyboard with 86 keys. It is a Win7 compliant keyboard, featuring a Windows key and other application keys.  Pointing Device The integrated Wide Touch Pad and two control buttons in the palm rest allow control of the on-screen pointer and support functions such as multi-touch touchpad gestures and window scrolling.
  • Page 20 Error! No text of specified style in document. Error! No text of specified style in document. Hardware Overview function. Satellite T210/T215/Pro T210/T215/PORTEGE T210 Maintenance Manual...
  • Page 21 1 Hardware Overview Error! No text of specified style in document. Error! No text of specified style in document.  Bridge Media Slot This slot allows you to insert SD, MiniSD/ MicroSD (through adapter), Memory Stick/Memory Stick Duo (through adaptor), Memory Stick Pro/Memory Stick Duo (through adaptor), xD and MMC memory cards.
  • Page 22 Error! No text of specified style in document. Error! No text of specified style in document. Hardware Overview  Wireless LAN (BTO) Some computers in this series are equipped with a Wireless LAN card. This WLAN module may come in with the following types (depending on the model): ...
  • Page 23 1 Hardware Overview Error! No text of specified style in document. Error! No text of specified style in document.  Figure 1-1A shows the computer and its system unit configuration. Camera Camera LED Lens Blue Kensington Lock Power BTN DC-IN RJ-45 Thermal Van Holes HDMI...

  • Page 24: Hardware Overview

    Error! No text of specified style in document. Error! No text of specified style in document. Hardware Overview Compal Confidential Clock Generator Mobile SLG8SP587VTR Model Name :NDU00/NDU10 page 12 File Name : LA-6031P Arrandale CPU BGA 1288pins Memory BUS(DDRIII) 200pin DDRIII-SO-DIMM X2 Dual Channel BANK 0, 1, 2, 3...
  • Page 25 1 Hardware Overview Error! No text of specified style in document. Error! No text of specified style in document. The system unit of the computer consists of the following components:  Processor (BTO) ® The computer is equipped with one of the following Intel processors: ...
  • Page 26  Graphics Controller ®  Intel Arrandale with Ibex Peak HM55 for integrated graphics.  Toshiba Value Added Package support featuring VideoStream Playback for external monitor under simultaneous display mode.  Dual external monitor support.  HDMI V1.3 support (without CEC) ...

  • Page 27: Mm (2.5-Inch) Hdd

    1 Hardware Overview Error! No text of specified style in document. Error! No text of specified style in document. 9.5mm (2.5-inch) HDD The computer contains an extremely low-profile and lightweight, high-performance HDD. The 9.5 mm HDD incorporates HDD Protection, and NCQ and 3D sensor support. The HDD interface conforms to Serial ATA.

  • Page 28: Power Supply

    Error! No text of specified style in document. Error! No text of specified style in document. Hardware Overview Power Supply The power supply unit provides constant voltage (19V) for the system board and performs the following functions: 1. Power input monitor ...
  • Page 29 1 Hardware Overview Error! No text of specified style in document. Error! No text of specified style in document. 6. Output monitor  Monitors the voltage output to the system block (load/logic circuit side).  Monitors the voltage, over-voltage, input/output current of the battery pack. ...

  • Page 30: Batteries

    Error! No text of specified style in document. Error! No text of specified style in document. Hardware Overview Batteries The computer has the following two types of batteries:  Main Battery Pack  Real Time Clock (RTC) Battery 1.4.1 Main Battery The main battery pack serves as the computer's main power source when the AC adapter is not attached.

  • Page 31: Rtc Battery

    1 Hardware Overview Error! No text of specified style in document. Error! No text of specified style in document. NOTE: The time required for normal charge depends on the power consumption by the system. Using a fluorescent lamp and frequently accessing the disk consumes more power and lengthens the charge time.
  • Page 32 Chapter 2 Troubleshooting Procedures...
  • Page 34 2 Troubleshooting Procedures Chapter 2 Contents Troubleshooting Introduction ..................3 Troubleshooting Flowchart..................4 Power Supply Troubleshooting ...................9 Display Troubleshooting ...................14 Keyboard Troubleshooting ..................17 2.6 External USB Devices Troubleshooting................19 2.7 Touch pad Troubleshooting .....................21 2.8 Speaker Troubleshooting ....................23 Wireless LAN Troubleshooting..................25 2.10 Camera Troubleshooting....................27 2.11 Bluetooth Troubleshooting ..................29 2.12...
  • Page 35 2 Troubleshooting Procedures Figures Figure 2-1 Troubleshooting flowchart (1/2)……………………………………………….5 Figure 2-1 Troubleshooting flowchart (2/2)……………………………………………….6 Figure 2-2 Power Supply Troubleshooting Process……………………………………….9 Figure 2-3 Display troubleshooting process……………………………………………...14 Figure 2-4 Keyboard troubleshooting process……………………………………………17 Figure 2-5 External USB device troubleshooting process………………………………..19 Figure 2-6 TouchPad troubleshooting process…………………………………………...21 Figure 2-7 Speaker troubleshooting process……………………………………………...23 Figure 2-8...

  • Page 36: Troubleshooting Introduction

    2 Troubleshooting Procedures Troubleshooting Introduction Chapter 2 describes how to determine if a Field Replaceable Unit (FRU) in the computer is causing the computer to malfunction. The FRUs covered are: 1. Display 7. Wireless LAN 13. 4 in 1 card 19.

  • Page 37: Troubleshooting Flowchart

    Ask the user if a password is registered, if it is, ask him or her to enter the password.  Verify with the customer that Toshiba Windows XP/Win7/Linux is installed on the hard disk. Operating systems that were not preinstalled by Toshiba can cause the computer to malfunction. ...

  • Page 38: Figure 2-1 Troubleshooting Flowchart (1/2)

    2 Troubleshooting Procedures S T A R T C o n n e c t th e A C a d a p te r to th e D C - IN s o c k e t P e rfo rm th e P o w e r S u p p ly T ro u b le s h o o tin g p ro c e d u re s Is th e D C -IN L E D o n ? in s e c tio n 2 .3...

  • Page 39: Figure 2-1 Troubleshooting Flowchart (2/2)

    2 Troubleshooting Procedures Perform the Keyboard Does typed characters appear correctly? Troubleshooting procedures in section 2.5 Insert USB memory disk. Then run the diagnostics test program Perform the HDD Is the diagnostics test loaded? Troubleshooting procedures in section 2.13 Allow each test to perform automatically After confirming which diagnostics test has detected...
  • Page 40 2 Troubleshooting Procedures If the diagnostics program cannot detect an error, the problem may be intermittent. The test program should be executed several times to isolate the problem. When a problem has been located, perform the appropriate troubleshooting procedures as follows: 1.
  • Page 41 2 Troubleshooting Procedures Other problems that are not covered by the diagnostics program may be discovered by a user. 1. If an error is detected when using an external USB device, perform the external USB Devices Troubleshooting procedures in Section 2.6 2.

  • Page 42: Power Supply Troubleshooting

    2 Troubleshooting Procedures Power Supply Troubleshooting ST A R T C heck P ower Supply Status (P rocedure 1) A re the D C -IN and R eplace adaptor / battery B attery LE D s lit? (P rocedure 2) C heck power supply connections (P rocedure 3)
  • Page 43 2 Troubleshooting Procedures as instructed. The flowchart in Figure 2-2 gives a summary of the process. The procedures described in this section are: Procedure 1: Power status check Procedure 2: Adaptor / battery replacement Procedure 3: Power supply connection check Procedure 4: Diagnostic check Procedure 5: Internal connection check Procedure 1...
  • Page 44 2 Troubleshooting Procedures Table 2-2 DC-IN LED DC-IN LED Power supply status Solid on AC power exists (LED is Green). No AC power exists. To check the power supply status, install a battery pack and connect an AC adaptor to the DC-IN port on the computer and to a power supply.
  • Page 45 2 Troubleshooting Procedures Procedure 3 Power supply connection check The power supply wiring diagram is shown below: AC adaptor cord AC power cord System Battery adaptor board Any of the connectors may be disconnected. Perform Check 1. Check 1 Disconnect the AC power cord from wall outlet. Check the power cable for breaks.
  • Page 46 2 Troubleshooting Procedures Procedure 4 Diagnostic check The power supply may not charge the battery pack. Perform the following procedures: 1. Reinstall the battery pack. 2. Attach the AC adaptor and turn on the power. If you cannot turn on the power, go to Procedure 5.

  • Page 47: Display Troubleshooting

    2 Troubleshooting Procedures Display Troubleshooting S T A R T P e r fo r m e x te r n a l d is p la y c h e c k (P r o c e d u re 1 ) D o e s th e e x te r n a l d is p la y f u n c tio n o k ? P e r fo r m d ia g n o s tic c h e c k...
  • Page 48 2 Troubleshooting Procedures This section describes how to determine if the computer’s display is functioning properly. The process is outlined in Figure 2-3. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: External display check Procedure 2: Diagnostic check Procedure 3: Connector and replacement check Procedure 1...
  • Page 49 2 Troubleshooting Procedures Procedure 3 Connector and replacement check The LCD module and system board are connected to the display circuits. Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: Check 1 Make sure the DDR module is seated properly.

  • Page 50: Keyboard Troubleshooting

    2 Troubleshooting Procedures Keyboard Troubleshooting S T A R T P e r f o r m d ia g n o s tic c h e c k ( P r o c e d u r e 2 ) K e y b o a r d is n o t W a s a k e y b o a rd f a u lty .
  • Page 51 2 Troubleshooting Procedures To determine if the computer’s keyboard is functioning properly, perform the following procedures. Figure 2-4 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic check Procedure 2: Connector and replacement check Procedure 1 Diagnostic check test and Diagnostics...

  • Page 52: 2.6 External Usb Devices Troubleshooting

    2 Troubleshooting Procedures 2.6 External USB Devices Troubleshooting S T A R T P e r f o r m e x t e r n a l d e v i c e a n d c o n n e c t i o n c h e c k ( P r o c e d u r e 1 ) D o e s t h e d e v i c e f u n c t i o n c o r r e c t l y w h e n...
  • Page 53 2 Troubleshooting Procedures To determine if the computer’s external USB devices are functioning properly, perform the following procedures. Figure 2-5 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: External device and connection check Procedure 2: Replace system board Procedure 1 External device and connection check The USB device may be damaged or the connection may be faulty.

  • Page 54: 2.7 Touch Pad Troubleshooting

    2 Troubleshooting Procedures 2.7 Touch pad Troubleshooting S T A R T P e r f o r m T o u c h p a d c h e c k ( P r o c e d u r e 1 ) D o e s T o u c h p a d f u n c t i o n o k ? P e r f o r m d i a g n o s t i c...
  • Page 55 2 Troubleshooting Procedures To determine if the computer’s built-in TouchPad is functioning properly, perform the following procedures. Figure 2-6 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: Perform Touchpad test Procedure 2: Touchpad connection check Procedure 3: Touchpad replacement check Procedure 1 Perform Touchpad test...

  • Page 56: Speaker Troubleshootin

    2 Troubleshooting Procedures 2.8 Speaker Troubleshooting S T A R T P e r f o r m a u d io s o u r c e te s t ( P r o c e d u r e 1 ) S p e a k e r s a r e n o t D o a ll s o u r c e s h a v e f a u lty .
  • Page 57 2 Troubleshooting Procedures To determine if the computer’s built-in speakers are functioning properly, perform the following procedures. Figure 2-7 outlines the process. First adjust the speaker volume to an appropriate level. Start with Procedure 1 and continue as instructed. Procedure 1: Audio source test Procedure 2: Earphone test Procedure 3: Connection check Procedure 4: Replacement check...

  • Page 58: Wireless Lan Troubleshooting

    2 Troubleshooting Procedures Wireless LAN Troubleshooting START Perform Wireless LAN connection check (Procedure 1) Wireless LAN system is not faulty. Continue Was a wireless LAN problem delected? troubleshooting - refer to Figure 2-1 Perform connector and replacement check (Procedure 2) Replace wireless LAN antenna/unit Replace system board Figure 2-8 Wireless LAN troubleshooting process...
  • Page 59 2 Troubleshooting Procedures The wireless LAN antenna wire, wireless LAN unit or system board may each be the source of a wireless LAN fault. Any of these components may be damaged. To determine if the computer’s wireless LAN system is functioning properly, perform the following procedures. Figure 2-8 outlines the process.

  • Page 60: Camera Troubleshooting

    2 Troubleshooting Procedures 2.10 Camera Troubleshooting Figure 2-9 Camera troubleshooting process Satellite T210/T215 Series Maintenance Manual...
  • Page 61 2 Troubleshooting Procedures The Camera board or system board may be the reason of a Camera fault. Either of these two components may be damaged. To determine if the computer’s Camera is functioning properly, perform the following procedures. Figure 2-9 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.

  • Page 62: Figure 2-10 Bluetooth Troubleshooting Process

    2 Troubleshooting Procedures 2.11 Bluetooth Troubleshooting Figure 2-10 Bluetooth troubleshooting process Satellite T210/T215 Series Maintenance Manual...
  • Page 63 2 Troubleshooting Procedures The Bluetooth antenna wire, Bluetooth module or system board may be the reason of a Bluetooth fault. Any of these components may be damaged. To determine if the computer’s Bluetooth is functioning properly, perform the following procedures. Figure 2-10 outlines the process.

  • Page 64: Figure 2-11 2 In 1 Card Troubleshooting Process

    2 Troubleshooting Procedures 2.12 4in1 card Troubleshooting START Perform 4 in 1 CARD test (Procedure 1) Do errors occur during 4 4 IN 1 unit is not IN 1 CARD test? faulty. Perform 4 IN 1 card socket replacement check (Procedure 2) Replace system board Figure 2-11 4 in 1 card troubleshooting process...
  • Page 65 2 Troubleshooting Procedures Procedure 2: 4 in 1 card socket check Procedure 1 4 in 1card test The 4 in 1 Card test card contains a 4 in 1 card test program. Ensure the card in fully inserted into the socket before running the program. If an error occurs during the 4 in 1 card test, perform Procedure 2.

  • Page 66: Figure 2-12 Hdd Troubleshooting Process

    2 Troubleshooting Procedures 2.13 HDD Troubleshooting Figure 2-12 HDD troubleshooting process Satellite T210/T215 Series Maintenance Manual...
  • Page 67 2 Troubleshooting Procedures The HDD or system board may be the reason of a HDD fault. Either of these two components may be damaged. To determine if the computer’s HDD is functioning properly, perform the following procedures. Figure 2-12 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.

  • Page 68: Figure 2-13 Crt Troubleshooting Process

    2 Troubleshooting Procedures 2.14 CRT Troubleshooting S T A R T P e r f o r m C R T c o n n e c t i o n c h e c k ( P r o c e d u r e 1 ) D o e s r e p l a c e m e n t R e p l a c e C R T C R T c a b l e...
  • Page 69 2 Troubleshooting Procedures Procedure 2: CRT set check Procedure 1 CRT connection check The CRT cable may be damaged or the connections may be loose. Perform Check 1: Check 1 Make sure CRT cable is firmly plugged into both the CRT set and the CRT port of the computer.

  • Page 70: Figure 2-14 Lan Troubleshooting Process

    2 Troubleshooting Procedures 2.15 LAN Troubleshooting S T A R T P e r f o r m d i a g n o s t i c c h e c k ( P r o c e d u r e 2 ) L A N i s n o t f a u l t y .
  • Page 71 2 Troubleshooting Procedures To determine if the computer’s LAN port is functioning properly, perform the following procedures. Figure 2-14 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: Diagnostic test Procedure 2: Connection and replacement check Procedure 1 Diagnostic test Run T&D Program on DOS model, which will display the LAN test result.

  • Page 72: Figure 2-15 Mic Troubleshooting Process

    2 Troubleshooting Procedures 2.16 MIC Troubleshooting Figure 2-15. MIC troubleshooting process The MIC module or system board may be the reason of a MIC fault. Either of these two components may be damaged. To determine if the computer’s MIC is functioning properly, perform the following procedures.
  • Page 73 2 Troubleshooting Procedures Procedure 2: Connector and replacement check Procedure 1 Windows Application test Run the functioning Program (record.exe) on Windows model, which will display the MIC test result. If tests and diagnostics result abnormal go to Procedure 2. If an error is not located, the MIC module functioning is properly.

  • Page 74: Figure 2-16 3D Sensor Troubleshooting Process

    2 Troubleshooting Procedures 2.17 3D Sensor Troubleshooting Figure 2-16. 3D sensor troubleshooting process The operation or system board may be the reason of 3D sensor fault. Either of these two may be damaged. To determine if the computer’s 3D is functioning properly, perform the following procedures.
  • Page 75 2 Troubleshooting Procedures Procedure 2 Replacement check Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks. Check 1 Make sure that 3D sensor test operation is correct, go to Check 2. Check 2 The system board may be damaged.

  • Page 76: Figure 2-17 3G Troubleshooting Process

    2 Troubleshooting Procedures 2.18 3G Troubleshooting S T A R T P e r f o r m W in d o w s a p p lic a tio n te s t ( P r o c e d u r e 1 ) 3 G s y s te m is n o t f a u lty .
  • Page 77 Procedure 2: Connector and replacement check Procedure 1 Windows Application check 1.> Please use TOSHIBA wireless manager. It displays the name of telecommunication company, and intensity of an electric wave. 2.> Please choose “About” and click “System Info”. “System Info” the Following data is displayed.
  • Page 78 2 Troubleshooting Procedures Procedure 2 Connector and replacement check The 3G antenna, 3G unit or system board may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks. Check 1 Make sure that the 3G antenna is firmly connected to the 3G module (refer to Chapter 4 for instructions) and that the 3G module is securely slotted into the system board.

  • Page 79: Hdmi Troubleshooting

    2 Troubleshooting Procedures 2.19 HDMI Troubleshooting S T A R T P e r fo rm H D M I c o n n e c tio n c h e c k (P r o c e d u re 1 ) D o e s re p la c e m e n t H D M I R e p la c e H D M I Y e s...
  • Page 80 2 Troubleshooting Procedures Procedure 1: HDMI connection check Procedure 2: HDMI set check Procedure 1 HDMI connection check The CRT cable may be damaged or the connections may be loose. Perform Check 1: Check 1 Make sure HDMI cable is firmly plugged into both the CRT set and the CRT port of the computer.

  • Page 81: E-Sata Troubleshooting

    2 Troubleshooting Procedures 2.20 E-SATA Troubleshooting START Perform E-SATA device check (Procedure 1) Is E-SATA transmission ok? Perform diagnostic check (Procedure 2) E-SATA port and transmission are not Was an E-SATA problem detected? faulty. Continue troubleshooting - refer to Figure 2-1 Perform connection and replacement check (Procedure 3) Replace system board...
  • Page 82 2 Troubleshooting Procedures To determine if the computer’s E-SATA system is functioning properly, perform the following procedures. Figure 2-19 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: E-SATA device check Procedure 2: Windows Application check Procedure 3: Connection and replacement check Procedure 1 E-SATA device check...

  • Page 83: 2.21 Wimax Troubleshooting

    2 Troubleshooting Procedures 2.21 Wimax Troubleshooting START Perform Wimax connection check (Procedure 1) Wimax system is not faulty. Continue Was a Wimax problem delected? troubleshooting - refer to Figure 2-1 Perform connector and replacement check (Procedure 2) Replace Wimax antenna/unit Replace system board Figure 2-20 Wimax troubleshooting process Notes: Wimax Antenna assemble rule as below:...
  • Page 84 2 Troubleshooting Procedures The Wimax antenna wire, Wimax unit or system board may each be the source of a Wimax fault. Any of these components may be damaged. To determine if the computer’s Wimax system is functioning properly, perform the following procedures. Figure 2-20 outlines the process.
  • Page 85 Chapter 3 Tests and Diagnostic...
  • Page 86 3.14 RTC Test ..........................26 3.15 G-sensor Test………..…………..………….…….……………..……………...……...28 3.16 HDD Test ………………...…………...…….………….……………..….…………..31 3.17 Read DMI Test………………...………………………………………...…..……………...34 3.18 Write DMI Test …………….…………………………….…………….…...…………….35 3.19 Toshiba Logo Set…………………………………..............37 3.20 Dynabook Logo Set………………………………...………...…….…………………….…39 3.21 TP Type R/W Test…….…………………….………………..…….……………………….41 3.22 EE-PROM SETTING…….…………………….……………………….……...……….…..44 Satellite T210/T215 Series Maintenance Manual...

  • Page 87: 3.1 The Diagnostic Test

     G-SENSOR TEST  HDD TEST  READ DMI TEST  WRITE DMI TEST  TOSHIBA LOGO SET  DYNABOOK LOGO SET  TP TYPE R/W TEST  EE-PROM SETTING You will need the following equipment to perform some of the Diagnostic test programs.

  • Page 88: 3.2 Executing The Diagnostic Test

    J. MAGNETIC SWITCH K. LAN TEST L. RTC TEST M. HDD TEST N. READ DMI O. WRITE DMI P. TP TYPE R/W TEST Q. EE-PROM SETTING R. G-SENSOR TEST S. TOSHIBA LOGO SET T. DYNABOOK LOGO SET Satellite T210/T215 Series Maintenance Manual...
  • Page 89 3. Tests and Diagnostics The below display will show up at the beginning of T&D program If the test result passes, the following display will show up: Satellite T210/T215 Series Maintenance Manual...
  • Page 90 3. Tests and Diagnostics If an error is detected and a test fails, the following message displays: Then press any key for next actions, the below display presented. Satellite T210/T215 Series Maintenance Manual...

  • Page 91: 3.3 Display Configuration

    3. Tests and Diagnostics 3.3 Display Configuration This Item will show the unit configuration. It includes:  CPU (CPU type; Cache ; CPU speed ;CPU FSB)  DDRAM SIZE  Panel ID  HDD type (Vendor ID. Model.)  VRAM size / VGA CHIP TYPE ...

  • Page 92: 3.4 Audio Sound Test

    3. Tests and Diagnostics 3.4 Audio sound test The audio sound test allows the user to aurally confirm the speaker functions. And the speaker will send out music during test. Before the Audio Test, you will see below note: Press any key, then the program will test below item: 1.
  • Page 93 3. Tests and Diagnostics If the function test fail, you can press “N” to stop test, and then it will display as below; Satellite T210/T215 Series Maintenance Manual...
  • Page 94 3. Tests and Diagnostics Press any key, the program will return to the below display, and you can press “Y” or “N” to judge the result. Satellite T210/T215 Series Maintenance Manual...

  • Page 95: 3.5 Fan On/Off Test

    3. Tests and Diagnostics 3.5 Fan ON/OFF Test The fan test allows the user to test aurally whether the fan is working. And follow the below procedures for this test:  The computer will let the fan be “ON” after any key pressed. Feel the wind or listen the rotating sound to check whether the fan is working or not.
  • Page 96 3. Tests and Diagnostics If FAN RPM check is OK, it will show as below: If FAN RPM check is NG, it will show as below: Satellite T210/T215 Series Maintenance Manual...

  • Page 97: Main Battery Charge Test

    3. Tests and Diagnostics 3.6 Main Battery Charge Test NOTE: The AC adaptor should be connected to successfully run this test . 45W with 19V DC for ALL SKU This test shows and measures the main battery:  Battery type (Lion) ...

  • Page 98: 3. 7 Fdd Test

    3 Tests and Diagnostics 3. 7 FDD Test NOTE: Before running the FDD test, prepare a formatted work diskette (1.44 MB). Need to insert FDD when power on machine. Otherwise the Floppy can not be detected. The Floppy Disk Test includes three subtests of the: 1.

  • Page 99: Memory Check

    3. Tests and Diagnostics 3.8 Memory check This test will check if the computer’s Memory Frequency and Size is correct in every slot. Before Memory test start, you should choice the below item: 1. Memory Read test 2. Memory Write test 3.
  • Page 100 3 Tests and Diagnostics When you execute this test, after you press the related number, the test picture will show as below: Memory Read Test Memory Write Test Satellite T210/T215 Series Maintenance Manual...
  • Page 101 3. Tests and Diagnostics Memory Read & Write Test Memory Info Test NOTE: Base on normal status, the Memory Info speed show 800/667, then the RAM is DDR2; if speed show 1066, and then the RAM is DDR3. Satellite T210/T215 Series Maintenance Manual...

  • Page 102: 3. 9 Keyboard Test

    3 Tests and Diagnostics 3. 9 Keyboard Test The keyboard test checks the all keys function. NOTE: The Num Lock and the Overlay mode must be off to execute the keyboard test. Before keyboard test starts, the keyboard matrix code should be chosen as below display: 1.
  • Page 103 3. Tests and Diagnostics Japan keyboard UK keyboard Satellite T210/T215 Series Maintenance Manual...

  • Page 104: 3.10 Mouse (Pad) Test

    3. Tests and Diagnostics 3.10 Mouse (Pad) Test The Mouse test allows the user to select and assign values to the following, using the Touch Pad or “Tab” key to move between selections: Mouse Speed (on a scale from slow to fast) Acceleration (Off, Low, Medium, High) Button Assignments (Left + Right / Right button, either Unassigned or Drag Lock)

  • Page 105: Lcd Pixels Mode Test

    3. Tests and Diagnostics 3.11 LCD Pixels Mode Test This LCD pixels mode test checks whether video display is fine. This test includes two modes of the test: 1. Text Mode - including 40*25 (16 colors) and 80*25 (2/16colors). 2. VGA Mode - including 320*200 (2/4/16 colors), 640*200 (2/16 colors), 640*350 (2/16 colors), 640*480 (2/16/256 colors).

  • Page 106: 3.12 Magnetic Switch Test

    3. Tests and Diagnostics 3.12 Magnetic Switch Test The Magnetic switch test checks the Magnetic function of the unit. When LCD cover closed, the Magnetic should enable to turn off the display. Follow below steps to run this test: 1. Close the LCD cover. 2.
  • Page 107 3. Tests and Diagnostics Satellite T210/T215 Series Maintenance Manual...

  • Page 108: 3.13 Lan Test

    3. Tests and Diagnostics 3.13 LAN Test The LAN test checks the LAN full-duplex environment. NOTE: LAN loopback needs to plug in before test begins. And LAN information will show on the test screen:  IO Base – Port: A000H ...
  • Page 109 3. Tests and Diagnostics The screen should display as below, indicating whether the subtests pass or fail when finished. If an error is detected and a test fails, the following message displays: Satellite T210/T215 Series Maintenance Manual...

  • Page 110: 3.14 Rtc Test

    3. Tests and Diagnostics 3.14 RTC Test Checks the computer’s RTC (Real Time Clock) and calendar functions by comparing the Free- DOS and CMOS values. The test runs automatically. The screen should display as below, indicating whether the test is passed or failed when finished. The screen will show below picture, if RTC test is OK.
  • Page 111 3. Tests and Diagnostics The screen will show below picture, if RTC test is FAIL. Satellite T210/T215 Series Maintenance Manual...

  • Page 112: G-Sensor Test

    3. Tests and Diagnostics 3.15 G-sensor test NOTE: please keep 90 degree between logic upper and LCD panel when test The display of a test program and the set method of PC are shown below. Display of a Test Program, The portion which PC and Test-Fixture contact is green. Upper Set method of PC <1>...
  • Page 113 3. Tests and Diagnostics Front Uppe 90° Set method of PC <4> Test 5: Left Uppe 90° Set method of PC <5> Test Result A test result is displayed when a test is completed. A display of result is O.K. or NG. And an error flag is returned at the end of a program.

  • Page 114: Hdd Test

    3. Tests and Diagnostics If the picture shows as below, it means the 3D G-sensor function is NG 3.16 HDD Test Satellite T210/T215 Series Maintenance Manual...
  • Page 115 3. Tests and Diagnostics NOTE: You can press “Ctrl + Fn + Break” key to stop HDD test if you want The HDD test allows the user to verify the HDD ok or not. First, please select HDD test method, Screen would display as below: After you select the method, then input password: “hard disk”, if input password is Right, the screen would display as below:...
  • Page 116 3. Tests and Diagnostics The screen will display as below picture to show the subtest is passed or failed when finished: If it is show the picture as below, it means HDD function is OK If the picture shows as below, it means he HDD function is NG Satellite T210/T215 Series Maintenance Manual...
  • Page 117 3. Tests and Diagnostics Satellite T210/T215 Series Maintenance Manual...

  • Page 118: Read Dmi

    3. Tests and Diagnostics 3.17 Read DMI Compal write Toshiba Part No (version), Toshiba Serial No (Serial No), Product Name, OEM string and UUID, If you want to double check the DMI data, please select Read DMI item, the figure below will be displayed:...

  • Page 119: Write Dmi

    3. Tests and Diagnostics 3.18 Write DMI When you want to write DMI data, please select which data you want to write, the figure below will be displayed: 1. Write Product (32) 2. Write Serial (32) 3. Write Version (32) 4.
  • Page 120 3. Tests and Diagnostics NOTE: should input correct DMI data, and should reboot the system that can make the setting effective. Satellite T210/T215 Series Maintenance Manual...

  • Page 121: Toshiba Logo Set

    3. Tests and Diagnostics 3.19 Toshiba Logo set Set the computer’s Toshiba Logo for other region except Japan SKU. The screen should display as below, indicating whether the test is passed or failed when finished. Press any key continue to auto set, if write OK, the following message displays:...
  • Page 122 3. Tests and Diagnostics When Toshiba Logo set finish, please restart machine, when show below Logo: Satellite T210/T215 Series Maintenance Manual...

  • Page 123: Dynabook Logo Set

    3. Tests and Diagnostics 3.20 Dynabook Logo set Set the computer’s Dynabook Logo for Japan SKU. The screen should display as below, indicating whether the test is passed or failed when finished. Press any key continue to auto set, if write OK, the following message displays: Satellite T210/T215 Series Maintenance Manual...
  • Page 124 3. Tests and Diagnostics When Dynabook Logo set finish, please restart machine, when show below Logo: Satellite T210/T215 Series Maintenance Manual...

  • Page 125: Tp Type R/W Test

    3. Tests and Diagnostics 3.21 TP TYPE R/W TEST This T/P TYPE R/W test checks the computer’s T/P TYPE and users write T/P vendor ID into EEPROM. The test runs automatically. The screen should display as below, indicating whether the test is passed or failed when finished. If write T/P type fail, the screen would display as below Satellite T210/T215 Series Maintenance Manual...
  • Page 126 3. Tests and Diagnostics If read T/P type fail, the screen would display as below If W/R T/P type passes, the screen would display as below Satellite T210/T215 Series Maintenance Manual...
  • Page 127 3. Tests and Diagnostics Satellite T210/T215 Series Maintenance Manual...

  • Page 128: Ee-Prom Setting

    3. Tests and Diagnostics 3.22 EE-PROM SETTING This EE-PROM SETTING will set the computer’s function status into EEPROM, included supported function and no support function. NOTE: Should perform EE-PROM SETTING once change M/B. It defined as normal rule. The screen should display as below: If press “1”...
  • Page 129 3. Tests and Diagnostics If this unit has MIC function, press “Y” then program will set MIC enable automatically as below: If this unit has no MIC function, press “N” then program will set MIC disable automatically as below: Then press any key go back to EE-PROM SETTING option as below: Satellite T210/T215 Series Maintenance Manual...
  • Page 130 3. Tests and Diagnostics If press “7” to disable all no support function, program will perform automatically as below: Satellite T210/T215 Series Maintenance Manual...
  • Page 131 3. Tests and Diagnostics Then press any key to go back to EE-PROM SETTING option as below: Satellite T210/T215 Series Maintenance Manual...
  • Page 132 3. Tests and Diagnostics If press “9” program will go back to test title as below: Satellite T210/T215 Series Maintenance Manual...
  • Page 133 Chapter 4 Replacement Procedures...
  • Page 134 4 Replacement Procedures Chapter 4 Contents General ........................4-1 Safety Precautions ..................4-3 Before You Begin................... 4-5 Disassembly Procedures................. 4-6 Assembly Procedures ..................4-6 Tools and Equipment ..................4-7 Screw Tightening Torque................4-7 Colors of Screw Shanks ................. 4-8 Symbols of Screws on the Laptop Body ............4-8 Symbol examples ...................
  • Page 135 4 Replacement Procedures Touch Pad Assembly.................... 4-24 Removing the Touch Pad Assembly ............4-24 Installing the Touch Pad Assembly.............. 4-26 WLAN Card ......................4-27 Removing the WLAN Card................4-27 Installing the WLAN Card ................4-27 4.10 WWAN Card......................4-28 Removing the WWAN Card ................ 4-28 Installing the WWAN Card................
  • Page 136 4 Replacement Procedures Installing the LED Cable and LED Board ........... 4-40 4.19 Speakers ....................... 4-41 Removing the Speakers................4-41 Installing the Speakers ................. 4-41 4.20 Thermal Module ....................4-42 Removing the Thermal Module ..............4-42 Installing the Thermal Module..............4-43 4.21 LCD Bezel......................
  • Page 137 4 Replacement Procedures Figures Figure 4.1 Removing the battery pack................... 4-9 Figure 4.2 Removing the bottom door................. 4-11 Figure 4.3 Removing the right hand RAM from the laptop ..........4-12 Figure 4.4 Removing left hand RAM from the laptop............4-12 Figure 4.5 Removing the bottom door.................
  • Page 138 4 Replacement Procedures Figure 4.32 Removing the LED board................. 4-40 Figure 4.33 Removing the speakers..................4-41 Figure 4.34 Disconnecting the thermal fan cable from the motherboard ......4-42 Figure 4.35 Removing the four screws from the thermal module ........4-43 Figure 4.36 Applying Shinetsu 7762 grease on the thermal module........

  • Page 139: General

    4.14 Bluetooth Module 4 Replacement Procedures General This chapter explains how to disassemble the laptop and replace Field Replaceable Units (FRUs). Some replacement procedures may not require you to remove all the surrounding FRUs to replace only one FRU. The chart below shows the FRUs in the order in which they should be removed in a top-down manner, irrespective of their physical locations.
  • Page 140 4 Replacement Procedures 4.14 Bluetooth Module 4.2 Battery 4.3 Memory 4.4 HDD 4.7 Power Button Board 4.5 Keyboard 4.6 Logic Upper Assembly 4.8 Touch Pad Assembly 4.9 WLAN Card 4.10 IO Board 4.11 Minicard Brackets 4.20 LCD Bezel 4.12 HDD Board 4.13 Bluetooth 4.14 VGA Board 4.21 LCD Module...

  • Page 141: Safety Precautions

    DANGER: Always use the original batteries or replacement batteries authorized by Toshiba. Batteries other than those differ in specifications and are incompatible with the laptop. They may burst or explode. To avoid leakage of alkaline solutions, never heat or disassemble the battery packs.
  • Page 142 For AC input, be sure to use the AC adapter and AC power cable that come with your laptop or Toshiba-recommended equivalents. To avoid the risk of electrical shock, make sure that all the replacement components meet the specifications of the laptop and that all the cables and connectors are fastened securely.

  • Page 143: Before You Begin

    4.14 Bluetooth Module 4 Replacement Procedures Before You Begin Before you begin to disassemble the laptop, keep in mind the precautions and advice in this section. Always begin disassembly by removing the AC adapter and battery pack. Remove the optional parts and accessories as well. The procedures for removing the batteries will be explained later.

  • Page 144: Disassembly Procedures

    4 Replacement Procedures 4.14 Bluetooth Module Disassembly Procedures The cable connectors come in these two basic types:  Pressure plate connectors  Normal pin connectors To remove a pressure plate connector, pull up the tabs on either side of the connector's plastic pressure plate and gently pull the cable out of the connector.

  • Page 145: Tools And Equipment

    4.14 Bluetooth Module 4 Replacement Procedures Tools and Equipment For your safety and that of other people in the working environment, it is strongly recommended that you use electrostatic discharge (ESD) equipment. The proper use of this equipment will ensure successful repair work and reduce the costs for repairing damaged components. The equipment and tools required for disassembly and reassembly are: ...

  • Page 146: Colors Of Screw Shanks

    4 Replacement Procedures 4.14 Bluetooth Module Colors of Screw Shanks For easy identification of the correct screws, the screw shanks are colored according to their lengths, as follows:  Screws of an odd-numbered length Blue  Screws of a special length Black Screws of a special length are those of a length having decimal places (i.e.

  • Page 147: Figure 4.1 Removing The Battery Pack

    4.14 Bluetooth Module 4 Replacement Procedures Battery Removing the Battery Pack Remove the battery pack according to the following procedures and Figure 4.1. CAUTION: When handling the battery packs, use care not to short circuit the terminals. Do not drop, hit, twist, or bend the battery packs. Do not scratch or break up their casing. 1.

  • Page 148: Installing The Battery Pack

    Always dispose of the battery packs as required by local ordinances or regulations. Use only replacement batteries recommended by Toshiba. NOTE: Visually check the battery's terminals. If they are dirty, clean them with a dry cloth.

  • Page 149: Figure 4.2 Removing The Bottom Door

    4.14 Bluetooth Module 4 Replacement Procedures Memory Removing the Optional Memory Remove the optional memory according to the following procedures and Figure 4.2 after checking that the laptop is turned off. CAUTION: Remove the optional memory after turning off the laptop. If this is violated, the laptop or memory can be damaged.

  • Page 150: Figure 4.3 Removing The Right Hand Ram From The Laptop

    4 Replacement Procedures 4.14 Bluetooth Module 4. Pull the two memory lock latches outward so that the memory pops up. 5. Pull the memory up and out at a 45 degree angle, using care to avoid touching the connectors. Figure 4.3 Removing the right hand RAM from the laptop 6.

  • Page 151: Installing The Optional Memory

    4.14 Bluetooth Module 4 Replacement Procedures Installing the Optional Memory Install the optional memory according to the following procedures after checking that the laptop is turned off. CAUTION: Install the optional memory after turning off the laptop. If this is violated, the laptop or memory can be damaged.

  • Page 152: Figure 4.5 Removing The Bottom Door

    4 Replacement Procedures 4.14 Bluetooth Module Removing the HDD CAUTION: Do not press on the top or bottom of the drive. Applying such pressure can either corrupt the data in the drive or damage the drive. Remove the HDD (hard disk drive) according to the following procedures and Figures 4.5 and 4.6.

  • Page 153: Figure 4.6 Removing The Hdd Pack From The Hdd Bay

    4.14 Bluetooth Module 4 Replacement Procedures 4. Remove the two M2x3 screws securing the HDD pack to the HDD bay. 5. Pull the tab in the direction indicated in Figure 4.6 to release the HDD, and then remove the HDD pack. M2x3*2 Figure 4.6 Removing the HDD pack from the HDD bay NOTE: Do not disassemble the HDD pack when it is working normally.

  • Page 154: Figure 4.7 Removing The Hdd Foil

    4 Replacement Procedures 4.14 Bluetooth Module M3x3*4 Figure 4.7 Removing the HDD foil CAUTION: Do not apply pressure to the top or bottom of the drive. Installing the HDD Install the HDD according to the following procedures. CAUTION: To avoid damage, always hold the HDD only by its sides. 1.

  • Page 155: Figure 4.8 Removing The Keyboard

    4.14 Bluetooth Module 4 Replacement Procedures Keyboard Removing the Keyboard Remove the keyboard according to the following procedures and Figures 4.8, 4.9. 4.10 and 4.11. 1. Close the laptop and turn it upside down. 2. Remove the two M2x6 screws securing the keyboard to the logic lower assembly as shown in Figure 4.8.

  • Page 156: Figure 4.9 Releasing The Keyboard Hooks

    4 Replacement Procedures 4.14 Bluetooth Module 3. Open the laptop screen and hold the unit upside down, taking care not to put undue stress on the screen hinges. Use a slim object such as a paperclip or a flathead screwdriver to release the three hooks securing the keyboard to the logic assembly as shown in Figure 4.9.

  • Page 157: Figure 4.11 Removing The Keyboard

    4.14 Bluetooth Module 4 Replacement Procedures 5. Shift the keyboard upward to expose the connectors as shown in Figure 4.11. 6. Unlock and disconnect the keyboard FCC cable from the logic upper assembly, and then remove the keyboard. Figure 4.11 Removing the keyboard Installing the Keyboard Install the keyboard according to the following procedures.

  • Page 158: Logic Upper Assembly

    4 Replacement Procedures 4.14 Bluetooth Module Logic Upper Assembly Removing the Logic Upper Assembly Remove the logic upper assembly according to the following procedures and Figures 4.12, 4.13 and 4.14. 1. Close the laptop and turn it upside down. 2. Remove the eight M2x6 screws securing the logic upper assembly to the logic lower assembly.
  • Page 159 4.14 Bluetooth Module 4 Replacement Procedures 3. Turn the laptop right side up and open it. 4. Disconnect the power board FFC, touch pad FFC and RGB board FFC. 5. Remove the two M2x3 and one M2x6 screws securing the logic upper assembly to the logic lower assembly.

  • Page 160: Installing The Logic Upper Assembly

    4 Replacement Procedures 4.14 Bluetooth Module 7. Work your way around the edges and across the bottom edge, and remove the logic upper assembly. Figure 4.14 Prying up the logic upper assembly Installing the Logic upper assembly Install the logic upper assembly according to the following procedures. 1.

  • Page 161: Power Button Board

    4.14 Bluetooth Module 4 Replacement Procedures Power Button Board Removing the Power Button Board Remove the power button board according to the following procedures and Figure 4.15. 1. Remove one M2x3 screw securing the power button board to the back of the logic upper assembly.

  • Page 162: Touch Pad Assembly

    4 Replacement Procedures 4.14 Bluetooth Module Touch Pad Assembly Removing the Touch Pad Assembly Remove the touch pad assembly according to the following procedures and Figures 4.16, 4.17 and 4.18. 1. Turn the logic upper assembly upside down. 2. Disconnect the touch pad FFC and remove the two M2x2 and one M2x3 screws securing the touch pad assembly to the logic upper assembly as shown in Figure 4.16.
  • Page 163 4.14 Bluetooth Module 4 Replacement Procedures 3. Raise the touch pad assembly from the top edge, and remove it from the logic upper assembly. Figure 4.17 Removing the touch pad assembly 4. Place the touch pad assembly on a flat surface such as a desk. 5.

  • Page 164: Installing The Touch Pad Assembly

    4 Replacement Procedures 4.14 Bluetooth Module Installing the Touch Pad Assembly Install the touch pad assembly according to the following procedures. 1. Place the touch pad button board on the touch pad bracket in the correct position and secure it with one M2x2 screw. 2.

  • Page 165: Wlan Card

    4.14 Bluetooth Module 4 Replacement Procedures WLAN Card Removing the WLAN Card Remove the WLAN card according to the following procedures and Figure 4.19. 1. Disconnect the two antennas from the WLAN card. 2. Remove the two M2x3 screws securing the WLAN card to the motherboard. The card pops up automatically.

  • Page 166: Wwan Card

    4 Replacement Procedures 4.14 Bluetooth Module 4.10 WWAN Card Removing the WWAN Card Remove the WWAN card according to the following procedures and Figure 4.20. 1. Disconnect two antenna cables from the WWAN card. 2. Remove the two M2x3 screws securing the WWAN card. The card pops up automatically. 3.

  • Page 167: Io Board

    4.14 Bluetooth Module 4 Replacement Procedures 4.11 IO Board Removing the IO Board Remove the IO board according to the following procedures and Figures 4.21 and 4.22: 1. Remove the two M2x3 screws securing the IO board to the logic lower assembly. 2.

  • Page 168: Installing The Io Board

    4 Replacement Procedures 4.14 Bluetooth Module 3. Lift the IO board up to an angle and then remove it from the logic lower assembly. Take care to disengage the connectors from their respective ports without damaging them. Figure 4.22 Sliding out the IO Board Installing the IO Board Install the IO board according to the following procedure: 1.

  • Page 169: Minicard Brackets

    4.14 Bluetooth Module 4 Replacement Procedures 4.12 Minicard Brackets Removing the Minicard Brackets There are two minicard brackets on the logic lower assembly. Remove each of the minicard brackets according to the following procedures and Figures 4.23 and 4.24: 1. Remove one M2x3 screw securing the minicard bracket to the logic lower assembly, as shown in Figure 4.23.

  • Page 170: Installing The Minicard Brackets

    4 Replacement Procedures 4.14 Bluetooth Module 2. Remove one M2x3 screw securing the minicard bracket to the logic lower assembly as shown in Figure 4.24. M2x3*1 Figure 4.24 Removing the minicard bracket 2 Installing the Minicard Brackets Install the minicard brackets according to the following procedures: 1.

  • Page 171: Figure 4.25 Removing The Hdd Board

    4.14 Bluetooth Module 4 Replacement Procedures 4.13 HDD Board Removing the HDD Board Remove the HDD board according to the following procedures and Figure 4.25: 1. Disconnect the HDD board cable from the motherboard and remove the two M2x3 screws securing the HDD board to the logic lower assembly, as shown in Figure 4.25.

  • Page 172: Figure 4.26 Removing The Bluetooth Module

    4 Replacement Procedures 4.14 Bluetooth Module 4.14 Bluetooth Module Removing the Bluetooth Module Remove the Bluetooth module according to the following procedure and Figure 4.26: 1. Disconnect the Bluetooth cable from the motherboard and then remove the Bluetooth module. Figure 4.26 Removing the Bluetooth module Installing the Bluetooth Module Install the Bluetooth module according to the following procedure: 1.

  • Page 173: Figure 4.27 Removing The Rgb Board

    4.14 Bluetooth Module 4 Replacement Procedures 4.15 RGB Board Removing the RGB Board Remove the RGB board according to the following procedures and Figure 4.27: 1. Disconnect the RGB board cable and remove one M2x3 screw securing the RGB board to the logic lower assembly, as shown in Figure 4.27.

  • Page 174: Figure 4.28 Removing The Display Assembly

    4 Replacement Procedures 4.14 Bluetooth Module 4.16 Display Assembly Removing the Display Assembly Remove the display assembly according to the following procedures and Figure 4.28. 1. Peel back the tape on the LVDS cable and disconnect it from the motherboard. Pull the LVDS cable out from the routing channel on the logic lower assembly.

  • Page 175: Motherboard

    4.14 Bluetooth Module 4 Replacement Procedures 4.17 Motherboard Removing the Motherboard Remove the motherboard according to the following procedures and Figure 4.29: 1. Disconnect the speaker cable and LED cable from the motherboard as shown in Figure 4.29. 2. Pull the DC-in connector upward and disengage it from the port. 3.

  • Page 176: Figure 4.30 Installing The Motherboard

    4 Replacement Procedures 4.14 Bluetooth Module Installing the Motherboard Install the motherboard according to the following procedures and Figure 4.30. 1. Seat the motherboard in the correct position and secure it with two M2x4 screws as shown in figure 4.30. 2.

  • Page 177: Figure 4.31 Disconnecting The Led Cable

    4.14 Bluetooth Module 4 Replacement Procedures 4.18 LED Cable and LED Board Removing the LED Cable and Board Remove the LED cable and LED board according to the following procedures and Figures 4.31 and 4.32. 1. Disconnect the LED cable from the LED board as shown in Figure 4.31 and remove it. Figure 4.31 Disconnecting the LED cable Satellite T210/T215/Pro T210/Pro T215 Maintenance Manual 4-39...

  • Page 178: Figure 4.32 Removing The Led Board

    4 Replacement Procedures 4.14 Bluetooth Module 2. Depress the catches as shown in Figure 4.32 and remove the LED board. Figure 4.32 Removing the LED board Installing the LED Cable and LED Board Install the LED cable and LED board according to the following procedures. 1.

  • Page 179: Figure 4.33 Removing The Speakers

    4.14 Bluetooth Module 4 Replacement Procedures 4.19 Speakers Removing the Speakers Remove the speakers according to the following procedures and Figure 4.33. 1. Peel up the tape and free the speaker cables from the channels. 2. Pry up the speakers as shown in Figure 4.33 and remove them. Figure 4.33 Removing the speakers Installing the Speakers Install the speakers according to the following procedures.

  • Page 180: Thermal Module

    4 Replacement Procedures 4.14 Bluetooth Module 4.20 Thermal Module Removing the Thermal Module Remove the thermal module according to the following procedures and Figures 4.34 and 4.35. CAUTION: When removing the thermal module, keep in mind that he thermal module can become very hot during operation.

  • Page 181: Installing The Thermal Module

    4.14 Bluetooth Module 4 Replacement Procedures 2. Turn over the motherboard assembly and remove the four M2x4 screws in the order shown in Figure 4.35. M2x4*4 Figure 4.35 Removing the four screws from the thermal module 3. Remove the thermal module from the motherboard. Installing the Thermal Module CAUTION: When installing the thermal module, keep the following in mind:...
  • Page 182 4 Replacement Procedures 4.14 Bluetooth Module Install the thermal module according to the following procedures. 1. Apply Shinetsu 7762 grease on the thermal module as shown in Figure 4.36. If you are installing a new CPU thermal module, remove the release papers on the thermal pads first. Thermal Grease Thermal Pad Figure 4.36 Applying Shinetsu 7762 grease on the thermal module...
  • Page 183 4.14 Bluetooth Module 4 Replacement Procedures 3. Turn over the motherboard assembly. Seat the thermal fan in the correct position and secure with one M2x4 screw. Connect the thermal fan cable, as shown in Figure 4.38. M2x4 Figure 4.38 Connecting the thermal fan cable to the motherboard Satellite T210/T215/Pro T210/Pro T215 Maintenance Manual 4-45...

  • Page 184: Figure 4.39 Prying Up The Lcd Bezel

    4 Replacement Procedures 4.14 Bluetooth Module 4.21 LCD Bezel Removing the LCD Bezel Remove the LCD bezel according to the following procedures and Figures 4.39 and 4.40. 1. Remove the two screw rubbers on the LCD bezel. 2. Remove the two M2x6 screws securing the LCD bezel to the LCD cover assembly. 3.

  • Page 185: Figure 4.40 Removing The Lcd Bezel

    4.14 Bluetooth Module 4 Replacement Procedures 4. Work your way along the top and bottom inside edges of the LCD bezel until it is free of the LCD cover assembly, as indicated in Figure 4.40. Figure 4.40 Removing the LCD bezel 5.

  • Page 186: Figure 4.41 Removing The Lcd Panel

    4 Replacement Procedures 4.14 Bluetooth Module 4.22 LCD Module Removing the LCD Module Remove the LCD module to the following procedures and Figures 4.41 and 4.42. 1. Remove the six M2x4 screws securing the LCD panel to the LCD cover assembly, as shown in Figure 4.41.

  • Page 187: Figure 4.42 Disconnecting The Camera Cable

    4.14 Bluetooth Module 4 Replacement Procedures 2. If there is a piece of tape covering the connector, peel it up. Disconnect the camera cable as shown in Figure 4.42. Figure 4.42 Disconnecting the camera cable 3. Remove the four M2x3 screws securing the LCD hinges to the LCD panel in order as shown in Figure 4.43 and remove the LCD hinges.

  • Page 188: Figure 4.44 Removing The Lvds Cable

    4 Replacement Procedures 4.14 Bluetooth Module 4. Turn the LCD module over and place it face down on a protective surface, such as a foam pad. 5. Gently peel the clear connector tape from the back of the LCD panel and disconnect the LVDS cable connector.

  • Page 189: Installing The Lcd Module

    4.14 Bluetooth Module 4 Replacement Procedures Installing the LCD Module Install the LCD module according to the following procedures. 1. Connect the LVDS cable to the LCD panel connector, and adhere the clear tape to the back of the LCD panel. 2.

  • Page 190: Figure 4.45 Prying Up The Camera

    4 Replacement Procedures 4.14 Bluetooth Module 6. Camera Module Removing the Camera Module Remove the camera module according to the following procedures and Figure 4.45. 1. Gently pry up the camera as shown in Figure 4.45. 2. Pull the WLAN antennas out from channels and remove them from the LCD cover. Figure 4.45 Prying up the camera Installing the Camera Module Install the camera module according to the following procedures.

  • Page 191: Figure 4.46 Removing The Wlan Antennas

    4.14 Bluetooth Module 4 Replacement Procedures 4.23 WLAN Antennas Removing the WLAN Antennas Remove the WLAN antennas according to the following procedures and Figure 4.46. 1. Peel the bases of the WLAN antennas up from the LCD cover as shown in Figure 4.46, taking care not to damage the aluminium foil on the LCD cover.

  • Page 192: Figure 4.47 Installing The Wlan Antennas

    4 Replacement Procedures 4.14 Bluetooth Module Installing the WLAN Antennas Install the WLAN antennas according to the following procedures and Figure 4.47. 1. Adhere the bases of the white and black WLAN antennas to the LCD cover. Note that the white antenna is in the top left corner and the black antenna is in the top right corner of the LCD cover.

This manual is also suitable for:

Portege t210 seriesSatellite t215 seriesSatellite pro t210 series

Table of Contents