Preparation; Features; Tools And Supplies - Jensen VM9411 Instruction Manual

VM9411

PREPARATION

Congratulations on your purchase of the Jensen VM9411
Mobile Multimedia Receiver.
It's a good idea to read all of the instructions before beginning
the installation. We recommend having your Jensen VM9411
installed by a reputable installation shop.

Features

MULTI-ZONE
Allows up front passengers to listen to the radio while rear
passengers listen to a CD, MP3, WMA or watch DVDs
DVD
• Compatible formats: DVD-R, DVD-RW, DVD+R,
DVD+RW, CD-R, CD-RW, CD-DA, MP3, WMA, SVCD,
VCD and MPEG1, MPEG2 and JPEG
• Region 1 playback
• 16:9 Aspect ratio- Wide / Normal / Cinema
• Front panel DVD control
• High-speed Fast Forward / Fast Rewind 2X, 4X, 8X, 32X
• Play, Pause, Stop, Slow
• Chapter Up / Down
• MultiZone output 'Kid-Zone'
• Wolfson Microelectronics high performance 24-bit, 192
kHz DAC supports 6-channel and 2-channel "Down-Mix"
audio modes
• 16Mbit high-speed flash memory - 80nS access time
MP3/WMA
• GIGA MP3 - Store up to 999 MP3 files on a DVD
• ID3-tag compatible
• Direct track access
• Play, Pause, Stop, Track Up / Down
• 100 second (MP3), 200 second (WMA) ESP - Electronic
Skip Protection
CD
• CD-text compatible
• 4 second ESP - Electronic Skip Protection
AM/FM Tuner
• US/Euro/Latin/Asia Tuner
• 30 Station presets (18FM/12AM)
• JENSEN Plus Tuner II
Outboard Media Module
• Input adaptor for TV Tuner, XM Radio and iPod
TV Tuner (Included)
• VHF 2-13
• UHF 14-69
• TV antenna - (3.5mm antenna included)
• F-Connector/Coaxial Antenna Input (optional)
XM Ready
• Requires optional Terk XMD1000 tuner box
• Requires optional Terk XMDJEN100 or Jensen JXMC XM
cables
• Advanced display shows the artist, song title, and XM
channel and category at a glance
• Direct Channel entry
jLink Ready
• Controls and charges all iPod's except "Shuffle"
• Displays all text information including category, track
name, artist and channel number
Chassis
• 7-inch TFT active-matrix LCD - 336,960 pixels (1440W X
234H)
• Full automatic motorized TFT LCD flip-out and up
• 16-step TFT LCD tilt adjustment
• Beep Tone confirmation
• Heat management system - Incorporates forced air-
cooling to keep the chip-sets operating at nominal
temperatures
• Heavy duty galvanized chassis
General
• Full function infrared remote control
• Limited function infrared "Kid Zone" remote
• 1 NTSC composite video output for additional screens
• OSD- On Screen Display menu control
• High performance audio processor
• Electronic volume, bass, treble, balance and fader
• Bass center frequency adjustment - 60, 80, 100, 130,
150 and 200Hz
• Bass Q factor - 1.0, 1.25, 1.5 and 2.0
• Treble center frequency adjustment - 10, 12.5, 15 and
17kHz
• Subwoofer crossover - 80, 120 and 160Hz
• Subwoofer Phase - 0 - 180 degrees
• Subwoofer level - variable
• 100-ohm low impedance preamp outputs - all channels
• 5V Peak / 2V RMS RCA outputs - all channels
• 1-pair Front RCA outputs
• 1-pair Rear / Surround RCA outputs
• Single Subwoofer RCA output
• Center Channel RCA output
• 1-pair Headphone / Multi-ZONE RCA outputs
• 1-pair Auxiliary RCA A/V inputs
• Back-up camera input with reverse override
• Flex fader
• Front panel (when screen is closed) high contrast LCD
• Rotary encoder audio control
1
• Joystick menu navigation

Tools and Supplies

You will need these tools and supplies to install your
VM9411:
• Torx type, flat-head and Philips screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio (screwdriver, socket
wrench set or other tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16 – 18 gauge speaker wire
WARNING! Only connect the unit to a12-volt power
supply with proper grounding.
WARNING! Never install this unit where operation and
viewing could interfere with safe driving conditions.
WARNING! To reduce the risk of a traffic accident
(except when using for rear view video camera) never
use the video display function while driving the vehicle.
This is a violation of federal law.
WARNING! Never disassemble or adjust the unit.
WARNING! To prevent injury from shock or fire, never
expose this unit to moisture or water.
WARNING! Never use irregular discs.
WARNING! To prevent damage to the mechanism inside
this unit, avoid impact to the TFT monitor.
WARNING! Using an improper fuse may cause damage
to the unit and result in a fire.