Advertisement
11. Wall Vent Cutout (Figure 11)
oceeveasus
err. uareusua
0
c°s
center
to center.
II
_-
_
. WALLSTUD
• Willtheventductbe6" (15.24cm) round throughthewall or3-1/4" x 10"
(8.26 cmx 25.4 cm) rectangle, verticatlyinside the wall?
/"
• See Ducting Instructionsfor rear duct insidethe wall. Note: Cutout in the
wall must clear 3-1/4" x 10" (8.26 cm x 25.4 cm) transition elbow.
• Locate the closest stud to your proposed vent hole location. Use the r_ (/_._
followingchartto figurethe "X" dimension.Seethe illustrationfor the other
dimensions.
VERTICAL DUCT INSIDE WALL
. . .
6" Round (15.24cm)
3-1/4"x 10"
(Figure 11)
(8.26cmx 25.4cm)
THROUGH
THROUGH
"X" MINIMUM
4" (10.16 cm)
6"(15.24cm)
OUTSIDE W ALL
THE FLOOR
I"
)_
12.54cm
• A 1" (2.54cm) lengthof duct mustprotrudethroughthe wall for connection
_-
--
"=""_._"D'U'_Th
tOthe blower.
(_
NOTE:Optimum vent location is 11" to 17" from edge of cabinet. Vents _1_]
J'J_fT
locatedfrom 9-3/8"to 11" will requireunitto be raisedover blowerfor
_ / j f j
_r _.-iJ
/ _,3rf
/
_ _ _ Jr f Jttf
n_f
IF
•
installation.
METALJOUCTDucT
TAPE I DUCT
_TAPE
12. Install Blower (Prior To Installing Range) (Figure 12)
(Figure 12)
• Refertoyourvent plan. it may be desirableto attachpart of the ducting
to theblowerbeforeit is installed.
L'IOCATE
ELECTRICA
_'L
• Position theblower(seeillustration) and attachitto the floorwithat least
POWER IN
two (2)screws:
SHADED A REA I
• Applyducttape aroundblowerexhaust/duct j oint.
I
,3. Install Electrical (Figure 13)
• Note: Observe all localelectricalcodes.
• CAUTION:Makesure power to cable is OFF.
_
• Locatetheelectricpowersupplyinthe floor orwall, anyplace inthe shaded
/.-_,
5 FEET OF
areawhichwill clearthe blower.
_)
ELECTRICAL
CABLE
• DirectConnect.Pullthrough5' (152.4 cm)of electrical c able.
• Range Cord:Canadianunitsare equippedwitha range cord. Install a
(Figure 13)
corresponding r eceptacle.
• Usethree orfourconductor copperstandard powercable (seefront cover
__,_
w____
for properwire size.) If four conductorwire is used,see #15 for connection
/ _
cup
to range,
w_s,eR
• See frontcoverof theseinstructions for propersupplyconnection.
14. ConnectElectrical (Three ConductorWire)(Figure 14)
__o
t
• CAUTION:Makesure powerto cable is OFF.
• Remove the range electrical service cover, located on the back, lower
"-NEU'mAL(WHITE)
left-handcorner.
_CABLE
CLAMP _
• Installa 3/4" (1.91cm) clampin the hole providedbelowthe terminalblock. ,
• Strip 3" (7.62 cm) of outer insulationfrom the cable.
(Figure 14)
• Strip 1/2" (1.27 cm) of insulationfrom each wire,
• Pull the cable through the cable clamp. Attach the BLACK, RED, and
WHITE wires (see illustration.) Tighten the terminal block nuts and the
cable clamp and install cover.
• On ranges equippedwith a range cord, plug the cord into its receptacle.
• Skipto Step #16.
Advertisement
