Advertisement
INSPECTION
Please carefully unpack and inspect your machine
for shipping damage. Each unit is operated and thor-
oughly inspected before shipment, and any damage is
the responsibility of the delivering carrier who should
be notified immediately.
ELECTRICAL
This rotary polisher is designed to operate on a standard 15
amp,
volt,
60
hz, AC household curtent. Check that the
115
,
voltage shown on the serial number plate is suitable for the
supply available. Voltages below 105 volts or above
could cause damage to the motor.
NOTE: 230/250 volt
50
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This appliance is equipped with a cord hav-
ing an equipment-grounding conductor and grounding
plug. The plug must be inserted into an appropriate out-
let that is properly installed and grounded in accor-
dance with all local codes and ordinances.
WARN 1 NG :
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
Check with a qualified electrician or service person
if you are in doubt as to whether the outlet
Do
erly grounded.
not modify the plug provided
-
with the appliance
if it will not fit the outlet, have
a proper outlet installed by a qualified electrician.
This appliance is for use on a nominal 120-volt circuit,
and has a grounded plug that looks like the plug in "Fig.
A below. A temporary adaptor that looks like the adap-
.
tor in "Fig
below may be used to connect this plug
to a 2-pole receptacle as shown in "Fig. B below, if a
properly grounded outlet is not available. The tempo-
rary adaptor should be used only until a properly
grounded outlet (Fig. A) can be installed by a qualified
electrician. The green colored rigid ear, lug, or the like
extending from the adaptor must be connected to a per-
manent ground such as a properly grounded outlet box
cover. Whenever the adaptor is used, it must be held
in place by a metal screw.
PROPER GROUNDING
CONNECTION
Grounding Pin
I-
\ \
Grounded
Outlet
A
Tab For Groundina
Screw
ADAPTOR
Fig.
C
Page 2
125
volts
i s
prop-
GROUNDING
CONNECTION
USING
AN
ADAPTOR
Box
Grounded Outlet
flg. B
are
NOTE: Adaptors
not allowed In Canada.
OPERATION
U s e
CAUTION: For indoor
Only.
To prevent possible damage to the floor
when using the Brush optlon, use water or other
approved cleanlng solution while operating.
When using the pad optloln, always keep
the machine moving when In contact with the
WARNING:
HIGH STARTINQ TORQUE.
HOLD MACHINE FIRMLY WITH BOTH HANDS.
Ensure that the pad driver
1 . )
ly and in good shape. Install or change pad if necessary
for
(See Page 3
Plug the machine into a wall outlet
2. )
grounding instructions.
3 . )
Lower the handle by unlocking the adjustment handle
and moving the handle into position. Relock the handle
when it is in a comfortable position.
4.)
Check to be sure the pad driver or brush is installed
before starting.
With the switch lock@) rotated forward, squeeze one
5 . )
of the switch levers, turning the machine on. (These levers
can be operated independently of each other)
6.)
To stop the machine, release the switch lever
switch lock.
NOTE The machine is equipped with a circuit breaker to
protect the motor in the event
occurs. The circuit breaker is located
switch housing. Push the reset button to restart the ma-
chine. If the breaker trips again, correct the cause of over-
loading before proceeding.
7 . )
Do not let machine rest on pad. When finished with the
machine for the day return handle to the storage position.
safe
Be sure to leave machine in a
risk of being tipped over.
CONTROLS
or
brush is installed correct-
as
described in the
and
an
overload condition
at the bottom of the
place where there is no
Advertisement
