Page 1
Internal Use Only North/Latin America http://aic.lgservice.com Europe/Africa http://eic.lgservice.com Asia/Oceania http://biz.lgservice.com LED TV SERVICE MANUAL CHASSIS : LD34D MODEL: 55LA86** 55LA86**-Z* CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. P/NO : MFL67733205 (1304-REV01) Printed in Korea...
Page 54
2013 LED/LCD TV Engineering guide < Applicable Model : High-end Platform >...
Page 55
EPI Interface EPI(Embedded Point-Point Interface) TCON Features LOCK • Point-Point topology (support 2 Pair option) • CDR (Clock Data Recovery) • Bandwidth up to 1.85Gbps/pair at FHD 120Hz 10 bit application • Lock signal cascading and feedback to T-Con Figure1. Topology •...
Page 56
EPI Interface (mini-LVDS vs. EPI) Comparison What to change HF mini-LVDS LCM (T-con to S-Driver IC) FHD (10bit) HF mini-LVDS HF mini- LVDS 60Hz 120Hz 240Hz TCON No. of Signal 60pin 60pin 80pin Connector (2ea) (2ea) (2ea) -Difficult to upgrade bandwidth limit -Multiple number of wires needed for higher bandwidth (FHD 120Hz) EPI (Embedded clock P-to-P Interface)
Page 57
EPI Interface (mini-LVDS vs. EPI) HF mini-LVDS TCON TCON Lock Topology Protocol • Multi Drop • Point to Point Features • Data rate: 660Mbps • Data rate : 1.8Gbps @10bit, FHD120 • External clock • Embedded clock, Control • Fewer Lines : 12 •...
Page 58
NFC (Near field communication) Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimetres. Present and anticipated applications include contactless transactions, data exchange, and simplified setup of more complex communications such as Wi-Fi.
Page 59
Main PCB for Broadband Main + TCON all in one xxLA790V-Zx Chassis : LD34D PCB P/No : EAX65040103 Main processor, DDR Memory eMMC Memory Micom for Key/IR/Logo sensing To PSU PMIC Audio AMP EPI Wafer To module Level shifter WIFI/BT Front Spk Key+IR+Logo...
Page 60
Main PCB for Broadband Main + TCON all in one xxLA860V-Zx Chassis : LD34D To Camera PCB P/No : EAX65040103 Main processor, DDR Memory eMMC Memory Micom for Key/IR/Logo sensing To PSU PMIC Audio AMP EPI Wafer To module Level shifter USB 3.0 WIFI/BT Front Spk...
Page 61
Main PCB for Broadband Main + TCON all in one To LED Driver xxLA960V-Zx To Woofer To Camera Chassis : LD34D PCB P/No : EAX65040103 Main processor, DDR Memory eMMC Memory Micom for Key/IR/Logo sensing To PSU USB 3.0 Audio AMP LVDS Wafer To module WIFI/BT...
Page 72
Interconnection - 1 47LA790V-ZA [PCBs] Main PCB Power Board Local key Assy RF Assy WIFI Assy [Cables] Main / LPB 24Pin + Local Dimming Cable Main / Module EPI Cable 50& 50Pin LED driver / PSU IR 8Pin Cable WiFi 6Pin + RF 8Pin Cable SPK Cable...
Page 73
Interconnection - 2 47LA790V-ZA [PCBs] IR Assy [Cables] IR to Local Key 3Pin Cable IR to Logo Assy 4Pin Cable...
Page 74
Interconnection - 1 55LA860V-ZA [PCBs] Main PCB Power Board Local key Assy RF Assy WIFI Assy Camera Assy [Cables] Main / LPB 24Pin + Local Dimming Cable Main / Module EPI Cable 50& 50Pin LED driver / PSU WiFi 6Pin + RF 8Pin Cable SPK Cable Camera Cable...
Page 75
Interconnection - 2 55LA860V-ZA [PCBs] IR Assy [Cables] IR to Local Key 3Pin Cable IR cable...
Page 76
Interconnection - 1 60LA860V-ZA [PCBs] Main PCB Power Board Local key Assy RF Assy WIFI Assy Camera Assy [Cables] Main / PSU 18Pin Main / T-con LVDS Cable 41& 51Pin LED driver 14 Pin cable WiFi 6Pin + RF 8Pin Cable SPK Cable Camera Cable Local Dimming cable...
Page 77
Interconnection - 2 60LA860V-ZA [PCBs] IR Assy LED Driver T-con [Cables] IR to Local Key 3Pin Cable IR 8 Pin Cable...
Page 78
Interconnection - 1 47LA960V-ZA [PCBs] Main PCB Power Board Local key Assy RF Assy WIFI Assy Camera Assy [Cables] Main / PSU 18Pin Main / T-con LVDS Cable 41& 51Pin LED driver 14 Pin Cable WiFi 6Pin + RF 8Pin Cable SPK Cable Camera Cable Local Dimming cable...
Page 79
Interconnection - 2 47LA960V-ZA [PCBs] IR Assy LED Driver T-con [Cables] IR 5 Pin + Local Key 3 Pin Cable Woofer Cable...
Page 80
Introductions of 13Y RF ass’y + Magic Remote control 1. System 2. Remote Buttons 3. MR13 Block Diagram 4. Function List 5. Pairing/Un-pairing Method...
Page 81
1. System UART or USB RF Receiver Remote Pairing Information Transmission (Send to TV after Paired) • Static Calibration Data (Bypass only) • Remote FW ver. (Save also in Receiver) • BD_ADDR (Save also in Receiver) • Pairing Information Transmission Sequence •...
Page 82
2. Remote Buttons (M4 vs. MR13P) RF Unpaired RF Paired IR continuous BUTTON ETC. POWER IR_CODE RF_CODE repeat POWER 0x08 NONE IR only BACK 0x28 0x8028 VOICE SMART BACK POWER SMART 0x7C 0x807C ↑ BACK HOME 0x07 0x8007 ← 0x06 0x8006 →...
Page 83
3. MR13P Block Diagram MPU-6150 IR Emitter1 I2C ch1 Antenna (Gyro+ACC) (Invensense) IR Emitter2 512Kb BCM20702M (Voice Scene IR) (Serial F/M) BCM20733M A2 (BROADCOM) (BROADCOM) Bluetooth 4.0 Bluetooth 3.0 Light Key Button Control ( 4 x 4 ) 512Kbit Voice (Serial Flash) Antenna Partron...
Page 84
4. Function list 주요 Item Manufacturer Function Voice Codec WM8950 Wolfson 16KHz Sampling of Audio data Voice MEMS Mic. SPU0414HR5H Knowles Sensing Voice Sensing angular velocity of X, Y, Z-axis Gyro Sensor Motion MPU-6150 Invensense Sensor Accelerometer Sensing device tilt (Pitch & Roll angle) RF Antenna SDBTPTR3015 Partron...
Page 85
5. RF Pairing / Un-pairing Method Method Description • When do pairing, the remote should make pairing request IR signal(0x75) to TV. • When TV receive the IR signal, it Method1 should send "pairing request – If unpaired, just press "OK" button. packet"...
Page 86
Introductions of 13Y WIFI built in ass’y 1. Wi-Fi built in Ass’y feature 2. Wi-Fi built in Ass’y specification...
Page 89
Contents of LCD TV Standard Repair Process Error symptom (High category) Error symptom (Mid category) Page Remarks No video/Normal audio No video/No audio Video error, video lag/stop, fail tunning 3, 4 A. Video error Color error Vertical/Horizontal bar, residual image, light spot, external device color error No power B.
Page 90
Contents of LCD TV Standard Repair Process Detail Technical Manual Error symptom Content Page Remarks Check LCD back light with naked eye LED driver B+ 24V measuring method A. Video error_ No video/Normal audio Check White Balance value Power Board voltage measuring method TUNER input signal strength checking method A.
Page 91
Standard Repair Process Established A. Video error 2012. 12 .06 Error date LCD TV symptom No video/ Normal audio Revised date First of all, Check whether all of cables between board is inserted properly or not. (Main B/D↔ Power B/D, LVDS Cable,Speaker Cable,IR B/D Cable,,,) ☞A1 ☞A4 No video...
Page 92
Standard Repair Process Established A. Video error 2012. 12 .06 Error date LCD TV symptom No video/ No audio Revised date ☞A4 Check various voltages Check and of Power Board Normal No Video/ replace voltage? No audio ( 3.5V,12V,20V or 24V…) MAIN B/D Replace Power Board and repair...
Page 93
Standard Repair Process Established A. Picture Problem 2012. 12 .06 Error date LCD TV symptom Picture broken/ Freezing Revised date . By using Digital signal level meter ☞ A6 . By using Diagnostics menu on OSD ( Menu→ Set up→ Support → Signal Test ) Check RF Signal level - Signal strength (Normal : over 50%) - Signal Quality (Normal: over 50%)
Page 94
Standard Repair Process Established A. Picture Problem (DVB-S/S2) 2012. 12 .06 Error date LCD TV symptom Tuning fail, Picture broken/ Freezing Revised date Check RF signal cable (DVB satellite signal or not) ☞ A6 Check whether other equipments have problem or not. Check RF Signal level (By connecting RF Cable at other equipment) →...
Page 95
Standard Repair Process Established A. Video error 2012. 12 .06 Error date LCD TV symptom Color error Revised date ☞A8 ☞ A10/ A11 ※ Check and Check color by input replace Link -External Input Color Cable Color Color -COMPONENT Replace Main B/D Replace module error? (LVDS) and...
Page 96
Standard Repair Process Established A. Video error 2012. 12 .06 Error date LCD TV symptom Vertical / Horizontal bar, residual image, Revised date light spot, external device color error Vertical/Horizontal bar, residual image, light spot Replace Module ☞A8 ☞ A10/ A11 ☞...
Page 97
Standard Repair Process Established B. Power error 2012. 12 .06 Error date LCD TV symptom No power Revised date ☞A17 ☞A19 DC Power on Replace Check Power LED Normal Check Power by pressing Power Key Power On ‘”High” Power LED operation? On Remote control .
Page 98
Standard Repair Process Established B. Power error 2012. 12 .06 Error date LCD TV symptom Off when on, off while viewing, power auto on/off Revised date Check outlet ☞A22 Check A/C cord Check Power Off Replace Main B/D Error? Normal? Mode Abnormal Check for all 3- phase...
Page 99
Standard Repair Process Established C. Audio error 2012. 12 .06 Error date LCD TV symptom Revised date No audio/ Normal video ☞A24 ☞A25 Check user Check audio B+ 24V No audio Normal menu > of Power Board Screen normal voltage Speaker off Cancel OFF Replace Power Board and repair parts...
Page 100
Standard Repair Process Established C. Audio error 2012. 12 .06 Error date LCD TV symptom Wrecked audio/ discontinuation/noise Revised date → abnormal audio/discontinuation/noise is same after “Check input signal” compared to No audio ☞A25 Wrecked audio/ Check and replace Discontinuation/ Check audio speaker and Noise for...
Page 101
Standard Repair Process Established D. General Function Problem 2012. 12 .06 Error date LCD TV symptom Remote control & Local switch checking Revised date 1. Remote control(R/C) operating error Replace Main B/D ☞A27 ☞A27 ☞A27 Check & Repair Check R/C itself Normal Normal Check B+ 3.5V...
Page 102
Standard Repair Process Established D. Function error 2012. 12 .06 Error date LCD TV symptom External device recognition error Revised date Check technical Check External Input and information Signal Technical input Replace Main B/D Component - Fix information input? information? signal Recognition error - S/W Version...
Page 103
Standard Repair Process Established E. Noise 2012. 12 .06 Error date LCD TV symptom Circuit noise, mechanical noise Revised date Replace PSU(with LED driver) Check location Identify Circuit of noise noise type noise Replace LED driver Check location of Mechanical noise noise ※...
Page 104
Standard Repair Process Established F. Exterior defect 2012. 12 .06 Error date LCD TV symptom Exterior defect Revised date Zoom part with Module Replace module Adjust VCOM exterior damage damage ☞A28 Cabinet Replace cabinet damage Remote Replace remote controller controller damage Stand Replace stand...
Page 105
Standard Repair Process Established G. Network Error 2012. 12 .06 Error date LCD TV symptom Exterior defect Revised date Check Wired ethernet cable connection Check whether AP has a probelm or not. Check Network status Setting Network Networ Status ☞...
Page 106
Standard Repair Process Established G. CI+ Competibility Error 2012. 12 .06 Error date LCD TV symptom Exterior defect Revised date Check defect CI slot pin Check it’s worked CI+ 1.2 or 1.3 Check CI CAM status Setting Antenna CI information Check status of CI+ Key in the Read Is there...
Page 107
Contents of LCD TV Standard Repair Process Detail Technical Manual Continued from previous page Error symptom Content Page Remarks Check front display LED Check power input Voltage & ST-BY 3.5V B. Power error_No power Checking method when power is ON POWER BOARD voltage measuring method B.
Page 108
Standard Repair Process Detail Technical Manual Error Established A. Video error_No video/Normal audio 2012. 12 .06 symptom date LCD TV Revised Content Check White Balance value date <ALL MODELS> Entry method 1. Press the ADJ button on the remote controller for adjustment. 2.
Page 109
Standard Repair Process Detail Technical Manual Error Established A. Video error_No video/ Audio 2012. 12 .06 symptom date LCD TV Revised Content Power Board voltage measuring method date Check the DC 24V, 12V, 3.5V. 24 Pin (Power Board ↔ Main Board) SMAW200-H24S Power on Inverter On/off...
Page 110
Standard Repair Process Detail Technical Manual Error Established A. Video error_Video error, video lag/stop 2012. 12 .06 symptom date LCD TV Revised TUNER input signal strength checking method Content date <ALL MODELS> MENU support signal test select channel When the signal is strong, use the attenuator (-10dB, -15dB, -20dB etc.)
Page 111
Standard Repair Process Detail Technical Manual Error Established A. Video error_Video error, video lag/stop 2012. 12 .06 symptom date LCD TV Revised LCD-TV Version checking method Content date <ALL MODELS> 1. Checking method for remote controller for adjustment Version Press the IN-START with the remote controller for adjustment...
Page 112
Standard Repair Process Detail Technical Manual Error A. Video error _Vertical/Horizontal bar, residual Established 2012. 12 .06 symptom date image, light spot LCD TV Revised Content LCD TV connection diagram (1) date <ALL MODELS> As the part connecting to the external input, check the screen condition by signal...
Page 113
Standard Repair Process Detail Technical Manual Error Established A. Video error_Video error, video lag/stop 2012. 12 .06 symptom date LCD TV Revised TUNER checking part Content date <ALL MODELS> Checking method: 1. Check the signal strength or check whether the screen is normal when the external device is connected. 2.
Page 114
Standard Repair Process Detail Technical Manual Error Established A. Video error_Color error 2012. 12 .06 symptom date LCD TV Revised Adjustment Test pattern - ADJ Key Content date You can view 6 types of patterns using the ADJ Key Checking item : 1. Defective pixel 2.
Page 116
Appendix : Exchange EPI Cable or Main B/D (2) Abnormal Power Section Abnormal Power Section Solder defect, Short/Crack Abnormal Display Fuse Open, Abnormal power section Solder defect, Short/Crack Noise GRADATION GRADATION...
Page 117
Appendix : Exchange LPB(LED driver) No Light Dim Light Dim Light Dim Light...
Page 118
Appendix : Exchange the Module (1) Panel Mura, Light leakage Panel Mura, Light leakage Press damage Crosstalk Press damage Crosstalk Un-repairable Cases In this case please exchange the module. Press damage...
Page 119
Appendix : Exchange the Module (2) Vertical Line Vertical Block Vertical Block Source TAB IC Defect Source TAB IC Defect Source TAB IC Defect Horizontal Block Horizontal line Horizontal Block Gate TAB IC Defect Gate TAB IC Defect Gate TAB IC Defect Gate TAB IC Defect Gate TAB IC Defect Un-repairable Cases...
Page 120
LCD TV Revised Content Check front display LED date You can set the LG Logo Light to on or off by selecting OPTION in the main menus. Front LOGO LED control in the status of ST-BY Condition: Menu Option LG Logo Light ...
Page 121
Standard Repair Process Detail Technical Manual Error Established B. Power error _No power 2012. 12 .06 symptom date LCD TV Revised Content Check power input voltage and ST-BY 3.5V date For ’10 models, there is no voltage out for st-by purpose. When st-by, only 3.5V is normally on.
Page 122
Standard Repair Process Detail Technical Manual Error Established B. Power error _No power 2012. 12 .06 symptom date LCD TV Revised Content Checking method when power is ON date Check “power on” pin is high 24 Pin (Power Board ↔ Main Board) SMAW200-H24S Power on Inverter On/off...
Page 123
Standard Repair Process Detail Technical Manual Error Established B. Power error _Off when on, off whiling viewing 2012. 12 .06 symptom date LCD TV Revised Content POWER OFF MODE checking method date <ALL MODELS> Entry method 1. Press the IN-START button of the remote controller for adjustment 2.
Page 124
Standard Repair Process Detail Technical Manual Error Established C. Audio error_No audio/Normal video 2012. 12 .06 symptom date LCD TV Revised Content Checking method in menu when there is no audio date <ALL MODELS> Checking method 1. Press the MENU button on the remote controller 2.
Page 125
Standard Repair Process Detail Technical Manual Error Established C. Audio error_No audio/Normal video 2012. 12 .06 symptom date LCD TV Revised Voltage and speaker checking method Content date when there is no audio <ALL MODELS> 24 Pin (Power Board ↔ Main Board) ①...
Page 126
Standard Repair Process Detail Technical Manual Error D. Function error_ No response in remote controller, Established 2012. 12 .06 symptom key error date LCD TV Revised Content Remote controller operation checking method date <ALL MODELS> P4101 KEY1 KEY2 ③ +3.5V_ST LOGO/LED_R ④...
Page 127
Standard Repair Process Detail Technical Manual Error Established D. VCOM Adjustment 2012. 12 .06 symptom date LCD TV Revised Content Sequence of the Vcom adjustment date 1. Case ■ LCD module change ■ T-Con board change 2. Equipment ■ Service Remote controller 3.