LCD-Monitor Chassis LHA19PS Model 940Fn SERVICE Manual LCD Monitor Fashion Feature - Lustrous/Colorful Appearance(Design) - Integrated UI applied - Built-in Scaler Sync Separator - Connectivity : Analog (15p Dsub), Dual (24p DVI-D) - Power Consumption : 38W - DPMS : under 1 W (230Vac)
Page 2
Samsung Electronics Co.,Ltd. -This Service Manual is a property of Samsung 416, Maetan-3Dong, Yeongtong-Gu, Suwon City, Electronics Co., Ltd. Gyeonggi-Do, Korea, 443-742 Any unauthorized use of Manual can be punished Printed in Korea under applicable International and/or domestic P/N : BN82-00136C-00 law.
10 Operating Instructions and Installation 10 Operating Instructions and Installation 10-1 Front 1. Menu button For documentations or works involving heavy text. Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. 3) Internet : Medium brightness For working with a mixture of images such as text 2.
Page 4
10 Operating Instructions and Installation 4. Enter button / Source button 6. Power button Activates a highlighted menu item. / Use this button for turn the monitor on and off. Push the 'SOURCE', then selects the video signal while the OSD is off. (When the source button is 7.
10 Operating Instructions and Installation 10-3 Connecting the monitor Rear of Computer Rear of monitor New Model Macintosh Old Model Macintosh 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1.
10 Operating Instructions and Installation 10-4 Attaching a Base - This monitor accepts a 75mm x 75mm VESA-compliant mounting interface pad. A. Monitor B. Mounting interface pad 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3.
11 Disassembly and Reassembly 11 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the TFT-LCD monitors. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 11-1 Disassembly (Simple - Stand) Cautions: 1.
Page 8
11 Disassembly and Reassembly 3. Lift up the back cover and Use the jig to remove the shield lamp. 4. Disconnect cables. 5. Lift up the shield and disconnect LVDS cable. 11-2...
Page 9
11 Disassembly and Reassembly 6. Lift up the LCD panel. 11-2 Disassembly (HAS-Stand) 1. Place monitor face down on cushioned table. Remove 2 screws from the stand and remove front cover. 11-3...
Page 10
11 Disassembly and Reassembly 2. Lift up the back cover and Use the jig to remove the shield lamp. 3. Disconnect cables. 4. Lift up the shield and disconnect LVDS cable. 11-4...
Page 11
11 Disassembly and Reassembly 5. Lift up the LCD panel. 11-3 Reassembly Reassembly procedures are in the reverse order of disassembly procedures. 11-5...
Page 12
11 Disassembly and Reassembly Memo 11-6...
14 Reference Infomation 14 Reference Infomation 14-1 Technical Terms -TFT-LCD -Image Lock This means "Fineness adjustment " in LCD Monitor, (Thin film Transistor Liquid Crystal Display) ADC(Analog to Digital Converter) the features are "Fine" and "Coarse" This is a circuit that converts from analog signal to digital signals.
Page 16
14 Reference Infomation -Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm -Vertical Frequency The screen must be redrawn several times per sec- ond in order to create and display an image for the...
14 Reference Infomation 14-2 Pin Assignments Sync 15-Pin D-Sub Signal Cable Connector Type Separate Composite Sync-on-green Pin No. Green Green Green + H/V Sync. Blue Blue Blue DDC Return (GND) DDC Return (GND) DDC Return (GND) GND-R GND-R GND-R GND-G GND-G GND-G GND-B...
14 Reference Infomation 14-3 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer- generated video signals. Table 2-1 Timing Chart VESA Mode VGA2/ VGA3/ 640/75 Hz 800/60 Hz 800/75 Hz 1024/60 Hz 1024/75 Hz 1280/60 Hz...
14 Reference Infomation 14-4 Preset Timing Modes -If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on.
13 Circuit Descriptions 13 Circuit Descriptions 13-1 Overall Block Structure Power Tree 13-1-1 1. When the AD board is in DPMS state: 1.1 The Scaler consumes power up to 27mA 1.2 The power to the panel is switched off 1.3 The MCU consumes power up to 23mA. -->...
13 Circuit Descriptions Main Board Parts 13-1-2 1. Inverter: A conversion device that converts DC 6. MCU & EEPROM: I2C is a two-way serial bus of rated voltage/current to high ones necessary two lines that supports communications across for the panel lamp. the integrated circuits as well as between MCU, Scaler and EEPROM.
Page 29
13 Circuit Descriptions 13-1-3 IP BOARD BLOCK(POWER) Parts 13-1-4 IP BOARD BLOCK( INVERTER ) Parts I P BO A RD BO A RD B LO C K B LO C K ( I N V N V ERT ER ERT ER ) I N V ERT V ERT ER ER PA RT...
Page 30
13 Circuit Descriptions 13-1-5 IP BOARD ( inverter ) PROTECTION Parts BIZET INVERTER CONTROLER FAN7310 have 2-way of the PROTECTION MODE. 1. OVP[Over Voltage Protection] : If the Voltage of the series capacitors C10 & C15 is over the 2.0V, the Inverter latched-off.[See the Picture1] 2.
13 Circuit Descriptions 13-2 Trouble Shooting 13-2-1 IP BOARD(Power) Power On Change FUSE Check fuse 3 pin of FDM0565R Check the Vcc system Vcc system in normal: HIGH 1 pin of FDM0565R Check the drain system Check the main switching Normal: Switching Check the Check the...
Page 32
13 Circuit Descriptions 13-2-2 IP BOARD(Inverter) Power On Check the power system Check the IC drive 1 and 2 pins of FDM0565R Check MOSFET Check Protection Normal:0.6V~0.8V 1 and 2 pins of FDM0565R Check the OVP and OLR Check Protection circuits Normal:0.6V~0.8V Check any dimming...
13 Circuit Descriptions 13-4 IP BOARD(Inverter) Schematic Diagrams 13-8...
Page 35
4 Troubleshooting 4 Troubleshooting ’ • • • • • • “ ” 4-1 No Power When pin4 of CN600 is 0V does proper DC 5V appear at Change IP Board. Pin 6.7 of CN600 separately? When pin1 of IC600 is 5V does proper DC 3.3V appear Check IC600 related circuit at Pin 3 of IC600...
4 Troubleshooting 4-2 No Video (Analog) check signal cable connection and power Do X401,X901 oscillate Replace or check related circuit like as figure 1 properly? Is there R,G,B input at Check input part. R11,R106,R108,R117, R116,R115? Do Hsync,Vsync waveformgnal check input part appear at R147,R830,R142,R145 ? Does sync signal(figure 2,3) appear check IC400 and related circuit...
4 Troubleshooting 4-3 No Video (Digital) check signal cable connection and power Do X401,X901 oscillate Replace or check related circuit like as figure 1 properly? Is there R,G,B input at check input part R126 ~ R131 like as figure 4,5,6? Is there waveform figure 7 check input part at R132,R133,R140,R141?
3 Alignments and Adjustments 3 Alignments and Adjustments This section of the service manual explains how to use the RS232 JIG. This function is needed for AD board change and program memory (IC110) change. 3-1 Required Equipment The following equipment is necessary for adjusting the monitor: •...
3 Alignments and Adjustments 3-6 Service Function Spec. 3-6-1 How to Display Service Function OSD 1. The value for brightness and contrast should be changed to zero. 2. Within 5 seconds, press the (Enter/Source) key. 3. Service function OSD will be displayed. If you want to disable the service function OSD, you will have to power off.
Page 43
3 Alignments and Adjustments 3-6-3 How to Control Service Function OSD • After change the panel or lamp, you must reset service function OSD. • The case of panel change After changeing the panel, press the menu key within 5 seconds,. Then, panel Ch.
3 Alignments and Adjustments 3-7 How to execute DDC 1. Open file. 2. Select Port #1. 3. Select DDC file. 4.Click, "Next" Button 5. Type in the monitor serial number and press Enter. *Repeat this step 2 to 5 times in digital inputs after the analog input.
6 Electrical Parts List 6 Electrical Parts List -You can search for updated part codes through ITSELF web site. URL : http://itself.sec.samsung.co.kr/ 6-1 LS19HAPNSQ/EDC Parts list Level Loc. No. Code No. Description & Specification SA/SNA LS19HAPNSQ/EDC 940FN,SGT9/S19B0-LHA,19,LCD-MO,NETHERLAN M0002 BN90-00781N ASSY COVER REAR;LS19HAPASQ/EDC S.N.A...
5 Exploded View & Parts List 5 Exploded View and Parts List -You can search for updated part codes through ITSELF web site. URL : http://itself. sec. samsung.co.kr 5-1 Exploded View M0112 T0077 M0107 M0174 T0022 T0145 T0003 M0215 M0006...
1 Precautions 1 Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 Safety Precautions 1-1-1 Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
1 Precautions 1-2 Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1 Precautions 1-4 Installation Precautions 1. For safety reasons, more than two people are 6. Keep the antenna far away from any high-voltage required for carrying the product. cables and install it firmly. Contact with the high- voltage cable or the antenna falling over may 2.