Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt DC733-XE
Summary of Contents for DeWalt DC733-XE
- Page 1 INSTRUCTION MANUAL DC733-XE CORDLESS COMPACT 10 mm (3/8" ) DRILL/DRIVER...
-
Page 3: Definitions: Safety Guidelines
1) WORK AREA SAFETY Definitions: Safety Guidelines a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the The definitions below describe the level of severity for each signal presence of flammable liquids, gases or dust. -
Page 4: Electrical Safety
d) Remove any adjusting key or wrench before turning the power tool on. A performed. Use of the power tool for operations different from those intended wrench or a key left attached to a rotating part of the power tool may result in could result in a hazardous situation. -
Page 5: Extension Cords
Extension Cords WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects CAUTION: Use only extension cords that are approved by the country’s Electrical or other reproductive harm. Some examples of these chemicals are: Authority. -
Page 6: Important Safety Instructions For All Battery Packs
NOTE: Battery storage and carrying caps are provided for use n o ....no load speed ....Class I Construction whenever the battery is out of the tool or charger. Remove cap ....(grounded) .....earthing terminal before placing battery in charger or tool.... -
Page 7: Important Safety Instructions For All Battery Chargers
open eye for 15 minutes or until irritation ceases. If medical attention is needed, CAUTION: Burn hazard. To reduce the risk of injury, charge only D WALT the battery electrolyte is composed of a mixture of liquid organic carbonates and rechargeable batteries. -
Page 8: Charging Procedure
• Do not place any object on top of charger or place the charger on a soft 4. Once the Automatic Tune Up mode is complete, the charger will begin a surface that might block the ventilation slots and result in excessive internal maintenance charge;... -
Page 9: Important Charging Notes
HOT/COLD PACK DELAY b. Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. Some chargers have a Hot/Cold Pack Delay feature: when the charger detects a battery that is hot, it automatically starts a Hot Pack Delay, suspending charging c. -
Page 10: Operation
OPERATION A. Variable speed switch H. Grip B. Forward/reverse slider I. Battery pack WARNING: To reduce the risk of serious personal injury, turn tool off and C. Keyless chuck J. Release buttons disconnect tool from power source before making any adjustments or removing/ installing attachments or accessories. - Page 11 Forward/reverse Slider (Fig. 6) Inserting and Removing Bits FIG. 4 (Fig. 1, 4) To select forward or reverse rotation, use the forward/ reverse slider (B) as shown (see arrows on tool). 1. Open the chuck by turning the sleeve (P) counterclockwise and insert the bit WARNING:To reduce the risk of personal injury, always wait until the motor has shank.
-
Page 12: Maintenance
• Keep the motor running when pulling the bit back out of a drilled hole. This will 4. IF DRILL STALLS, it is usually because it is being overloaded or improperly used. help prevent jamming. RELEASE TRIGGER IMMEDIATELY, remove drill bit from work, and determine cause of stalling. - Page 13 WALT Industrial Tool Co., 20 Fletcher Road, Mooroolbark, VIC 3138 Australia or call 1800 654 155 or (NZ) 0800 339258. Guarantee 10mm (3/8”) DC733-XE Applicable to hand held Power Tools, Lasers and Nailers. CORDLESS DRILL DRIVER Three Year Limited Warranty...
- Page 16 20 Fletcher Road, Mooroolbark, VIC 3138 Australia (03 8720 5100) • 5 Te Apunga Place, Mt Wellington, New Zealand (0800 339258) (JUN09) Part No. N032278 DC733-XE Copyright © 2009 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...