Page 1 DCR-TRV890E/TRV900/TRV900E RMT-811/812 SERVICE MANUAL US Model Canadian Model DCR-TRV900 AEP Model UK Model DCR-TRV890E/TRV900E E Model Hong Kong Model Tourist Model DCR-TRV900/TRV900E Australian Model Photo: DCR-TRV900E RMT-811 Chinese Model Ver 1.0 1998.08 C MECHANISM DCR-TRV900E Difference table For MECHANISM ADJUSTMENTS, refer to the...
Page 2 MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
Page 3: Table Of Contents
TABLE OF CONTENTS SERVICE NOTE Deleting images ..............1-35 Copying the image recorded with the memory card slot to Power Supply During Repairs ..........6 mini DV tapes (DCR-TRV900E only) ......... 1-35 How to Take a Cassette Out When the Main Power Cannot Playing back images in a continuous loop - SLIDE SHOW ..
Page 4 • VI-151 (REC/PB AMP)(1/10) Setting the Switch ............5-4 Schematic Diagram ........4-51 Order of Adjustments ............5-4 • VI-151 (Timing Generator)(2/10) Subjects ................5-4 Schematic Diagram ........4-55 1-2. Initialization of F, E Page Data ........5-5 • VI-151 (Video Interface)(3/10) Initializing the F, E Page Data .........
Page 5 D Page Table ..............5-36 6-1-4. Cabinet (R) Section ............6-4 Initializing the B Page Data ........... 5-38 6-1-5. LCD Panel Section ............6-5 Modification of B Page Data ......... 5-38 6-1-6. Battery Panel Section ............6-6 B Page Table ..............5-38 6-1-7.
Page 6: Service Note
DCR-TRV890E/TRV900/TRV900E SERVICE NOTE POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied (8.4V) to the battery terminal using the service power cord (J-6082-223-A), the power is shut off so that the unit cannot operate. This following two methods are available to prevent this. Take note of which to use during repairs.
Page 7: Service Mode Display
DCR-TRV890E/TRV900/TRV900E SELF-DIAGNOSIS FUNCTION SELF-DIAGNOSIS DISPLAY SELF-DIAGNOSIS FUNCTION When problems occur while the unit is operating, the counter of the When problems occur while the unit is operating, the self-diagnosis viewfinder, LCD screen or LCD window consists of an alphabet function starts working, and displays on the viewfinder, LCD screen and 4-digit numbers, which blinks at 3.2 Hz.
Page 8 SELF-DIAGNOSIS CODE TABLE Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Condensation. Remove the cassette, and insert it again after one hour. Video head is dirty. Clean with the optional cleaning cassette. Non-standard battery is used. Use the info LITHIUM battery. LOAD direction.
Page 9 DCR-TRV890E/TRV900/TRV900E SECTION 1 This section is extracted from instruction GENERAL manual. (DCR-TRV890E/TRV900E model)
Page 18 1-10...
Page 19 1-11...
Page 20 1-12...
Page 21 1-13...
Page 22 1-14...
Page 23 1-15...
Page 24 1-16...
Page 25 1-17...
Page 26 1-18...
Page 27 1-19...
Page 28 1-20...
Page 29 1-21...
Page 30 1-22...
Page 31 1-23...
Page 32 1-24...
Page 33 1-25...
Page 34 1-26...
Page 35 1-27...
Page 36 1-28...
Page 37 1-29...
Page 38 1-30...
Page 39 1-31...
Page 40 1-32...
Page 41 1-33...
Page 42 1-34...
Page 43 1-35...
Page 44 1-36...
Page 45 1-37...
Page 46 1-38...
Page 47 1-39...
Page 48 1-40...
Page 49 1-41...
Page 50 1-42...
Page 51 1-43...
Page 52 1-44...
Page 53 1-45...
Page 54 1-46E...
Page 55: Cabinet (Upper) Assembly, Front Panel Assembly
DCR-TRV890E/TRV900/TRV900E SECTION 2 DISASSEMBLY NOTE: Follow the disassembly procedure as shown in the flow chart below. DCR-TRV890E/TRV900/TRV900E 2-1. Cabinet (upper) assembly, Front panel assembly 2-2. Battery panel assembly 2-3. Cabinet (R) assembly, Cabinet (L) assembly 2-4. SE-75 board @¢ - @¶...
Page 56: Battery Panel Assembly
1 Screw (M2 × 4) 2-2. BATTERY PANEL ASSEMBLY 2 Two screws (M2 × 4) 3 Screw (M2 × 4) 9 Cable CN3200 4P (VI-151 board) 4 CPC cover 6 Battery panel assembly Remove it by opening to a side a little together with the cabinet (R) assembly) 7 FP-18 flexible board CN7210 8P (CK-80 board) 8 Cable 3P, CN3201 3P (VI-151 board)
Page 57: Se-75 Boards
2-4. MECHANISM DECK, LENS ASSEMBLY, VC-208, VI-151, SE-75 BOARDS 1 - 5 Lens assembly 6 - !º VC-208 board !£ a flexible board (from capstan motor) !¡ - !• VI-151 board CN2912 27P (VI-151 board) !ª - @¡ Mechanism deck @™...
Page 58: Ck-80 Board
2-6. CK-80 BOARD !¶ Card ejector (Slide it in the direction 1 - 6 PM slider assembly of the arrow.) 7 - !¶ CK-80 board Insert the craw !• - @¡ Speaker into the slider when re-assembling. !∞ FP-9 flexible board CN7204 60P 1 Screw (M2 ×...
Page 59: Pd-101 Board
2-8. PD-101 BOARD !™ P cabinet (M) assembly 1 - 5 PD-101 board 6 - 8 FP-19 flexible board 9 - !™ LCD panel !º Light-conduction Craws plate insulation sheet !¡ LCD module Craws 9 Cold cathode fluorescent tube with light-conduction plate 2 Flexible board CN5701 10P 6 Panel frame...
Page 60: Ed-48, Vf-121 Boards
2-10.ED-48, VF-121 BOARDS 1 - 4 ED-48 board 5 - 8 EVF assembly 9 - !£ VF-121 board !¢ - !¶ VF slide base !∞ Slide here. !§ VF click plate !¶ VF slide base 4 Edit button !¢ Peel off the cushion. !£...
Page 61: Ma-333 Board
2-12.MA-333 BOARD !¢ MF retainer 1 - 7 MA-333 board 8 - 0 FP-22 flexible board (MIC jack) assembly !¡ - !¶ FP-21 flexible board !™ Tapping screw (B2 × 5) !£ MF reinforcement plate !¶ Screw (M2 × 3) !§...
Page 62: Rec/Pb Amp)
2-14.CIRCUIT BOARDS LOCATION LB-55 (EVF BACK-LIGHT) VF-121 (COLOR EVF) ED-48 (USER CONTROL) SE-75 (YAW/PITCH SENSOR) JK-163 (AUDIO/VIDEO IN/OUT) RI-10 (SIRCS RECEIVER) CK-80 MA-333 USER CONTROL, (STEREO MIC AMP) LCD DRIVE PD-101 (RGB DRIVER, TIMING GENERATOR, BACK-LIGHT) CD-202 (CCD IMAGER) VC-208 SAMPLE HOLD &...
Page 63: Flexible Boards Location
2-15.FLEXIBLE BOARDS LOCATION FK-4880 (USER CONTROL) FP-17 FP-23 (S-Y/C IN/OUT) FP-18 (USER CONTROL) For LED FP-16 FP-11 FP-13 FP-8 FP-19 (USER CONTROL) FP-20 FP-10 LENS BLOCK FP-21 (FOCUS) FP-9 (From CAPSTAN MOTOR) From LOADING MOTOR, S/T REEL SENSOR (From DRUM MOTOR) FP-22 (MIC JACK) FP-12...
Page 64: Overall Block Diagram
DCR-TRV890E/TRV900/TRV900E SECTION 3 BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM...
Page 65: Power Block Diagram
DCR-TRV890E/TRV900/TRV900E 3-2. POWER BLOCK DIAGRAM 3-8E...
Page 66: Printed Wiring Boards And Schematic Diagrams
DCR-TRV890E/TRV900/TRV900E SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM-1 FRAME SCHEMATIC DIAGRAM-1...
Page 67 DCR-TRV890E/TRV900/TRV900E FRAME SCHEMATIC DIAGRAM-2 FRAME SCHEMATIC DIAGRAM-2...
Page 68 DCR-TRV890E/TRV900/TRV900E DCR-TRV890E/TRV900/TRV900E 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) (Measuring conditions voltage and waveform) •...
Page 69 DCR-TRV890E/TRV900/TRV900E CD-202 BOARD CAMERA REC IC100 1, 2 IC101 1, 2 IC102 1, 2 8.4Vp-p IC100 3, IC101 3 IC102 3 22Vp-p IC100 !£, !¢ IC101 !£, !¢ IC102 !£, !¢ 3.0Vp-p 13.5 MHz IC100 !™, IC101 !™ IC102 !™...
Page 70: Cd-202 (Ccd Imager) Printed Wiring Board
DCR-TRV890E/TRV900/TRV900E DCR-TRV890E/TRV900/TRV900E CD-202 (CCD IMAGER) PRINTED WIRING BOARD CD-202 BOARD — Ref. No. CD-202 Board; 10,000 Series — C100 CN100 B-1 C101 C102 IC100 C103 IC101 C104 IC102 C105 C106 L100 C107 L101 C108 L102 C109 C110 Q100 C111 Q101...
Page 71 DCR-TRV890E/TRV900/TRV900E VC-208 (SAMPLE HOLD & AGC, CAMERA PROCESSOR, BASE BAND INPUT, MOTOR DRIVE, VAP DRIVER, CARD CONTROL, PWM CONTROL, HONEY, PCMCIA CONTROL) PRINTED WIRING BOARD — Ref. No. VC-208 Board; 10,000 Series — VC-208 BOARD (SIDE A) C228 C530 FB754...
Page 72 DCR-TRV890E/TRV900/TRV900E DCR-TRV890E/TRV900/TRV900E VC-208 (SAMPLE HOLD & AGC, CAMERA PROCESSOR, BASE BAND INPUT, MOTOR DRIVE, VAP DRIVER, CARD CONTROL, PWM CONTROL, HONEY, PCMCIA CONTROL) PRINTED WIRING BOARD — Ref. No. VC-208 Board; 10,000 Series — VC-208 BOARD (SIDE B) C201 E-13...
Page 73 DCR-TRV890E/TRV900/TRV900E DCR-TRV890E/TRV900/TRV900E For schematic diagram • Refer to page 4-17 for printed wiring board. VC-208 BOARD (1/7) IC203 @•, @ª IC203 9 CAMERA REC CAMERA REC 0.6Vp-p 0.34Vp-p IC203 #¡, #™ IC204 #¡ CAMERA REC CAMERA REC 3.4Vp-p 27.0 MHz 0.5Vp-p...
Page 74 DCR-TRV890E/TRV900/TRV900E DCR-TRV890E/TRV900/TRV900E For schematic diagram • Refer to page 4-17 for printed wiring board. VC-208 BOARD (2/7) !º IC300 &¶ CAMERA REC/PB 3.0Vp-p 13.5MHz !¡ IC302 $º CAMERA REC/PB 2.8Vp-p 20.0MHz CAMERA PROCESSOR 4-27 4-28 4-29 VC-208 (2/7)
Page 75 DCR-TRV890E/TRV900/TRV900E DCR-TRV890E/TRV900/TRV900E For schematic diagram • Refer to page 4-17 for printed wiring board. VC-208 BOARD (3/7) !™ IC1200 @∞ LINE REC 0.44Vp-p !™ IC1200 @∞ CAMERA REC/PB 1.0Vp-p !£ IC1200 #£ LINE REC 0.5Vp-p !£ IC1200 #£ CAMERA REC/PB 1.5Vp-p...
Page 76 DCR-TRV890E/TRV900/TRV900E DCR-TRV890E/TRV900/TRV900E For schematic diagram • Refer to page 4-17 for printed wiring board. MOTOR DRIVE 4-35 4-36 VC-208 (4/7)
Page 77 DCR-TRV890E/TRV900/TRV900E For schematic diagram SE-75 (YAW/PITCH SENSOR) PRINTED WIRING BOARD • Refer to page 4-17 for printed wiring board of VC-208. — Ref. No. SE-75 Board; 10,000 Series — SE-75 BOARD C450 C451 CN450 A-2 L450 SE450 SE451 For printed wiring boards •...
Page 78 DCR-TRV890E/TRV900/TRV900E For schematic diagram • Refer to page 4-17 for printed wiring board. VC-208 BOARD (6/7) CAMERA REC/PB !¶ IC722 !º 0.8Vp-p 2.3µsec CARD CONTROL, PWM CONTROL 4-43 4-44 4-45 4-46 VC-208 (6/7)
Page 79 DCR-TRV890E/TRV900/TRV900E For schematic diagram • Refer to page 4-17 for printed wiring board. VC-208 BOARD (7/7) !• IC751 &¶ CAMERA REC/PB 3.8Vp-p 6.85MHz HONEY, PCMCIA CONTROL 4-47 4-48 4-49 4-50 VC-208 (7/7)
Page 80 DCR-TRV890E/TRV900/TRV900E For schematic diagram • Refer to page 4-91 for printed wiring board. VI-151 BOARD (1/10) IC1816 1, 2, 6, 7 CAMERA REC 3.5Vp-p 6.8msec IC1816 !¡, !™ CAMERA REC 2.0Vp-p 6.8msec IC1816 @¶ PB 0.35Vp-p 6.8msec IC1816 $º CAMERA REC/PB 2.3Vp-p...
Page 81 DCR-TRV890E/TRV900/TRV900E DCR-TRV890E/TRV900/TRV900E For schematic diagram • Refer to page 4-91 for printed wiring board. VI-151 BOARD (2/10) CAMERA REC IC1900 $¡ 3.2Vp-p 13.5MHz TIMING GENERATOR 4-55 4-56 VI-151 (2/10)
Page 82 DCR-TRV890E/TRV900/TRV900E DCR-TRV890E/TRV900/TRV900E For schematic diagram • Refer to page 4-91 for printed wiring board. VI-151 BOARD (3/10) !º Q1500 E CAMERA REC 0.22Vp-p !º Q1500 E LINE REC 0.3Vp-p !¡ Q1501 E CAMERA REC 0.2Vp-p !¡ Q1501 E LINE REC 0.3Vp-p...
Page 83 DCR-TRV890E/TRV900/TRV900E DCR-TRV890E/TRV900/TRV900E For schematic diagram • Refer to page 4-91 for printed wiring board. VI-151 BOARD (4/10) CAMERA REC/PB !£ IC1600 !¢ (R1627) 2.6Vp-p 24.58MHz DCT/IDCT 4-62 4-63 4-64 VI-151 (4/10)
Page 84 DCR-TRV890E/TRV900/TRV900E DCR-TRV890E/TRV900/TRV900E For schematic diagram • Refer to page 4-91 for printed wiring board. VI-151 BOARD (5/10) !¢ IC1403 @™ LINE REC/PB (IR ON) 0.8Vp-p 82nsec !∞ IC1403 $¡ PB 0.5Vp-p !∞ IC1403 $¡ LINE REC 0.5Vp-p !§ IC1402 @∞...
Page 85 DCR-TRV890E/TRV900/TRV900E For schematic diagram • Refer to page 4-91 for printed wiring board. AUDIO PROCESSOR 4-68 4-69 4-70 VI-151 (6/10)
Page 86 DCR-TRV890E/TRV900/TRV900E For schematic diagram • Refer to page 4-91 for printed wiring board. VI-151 BOARD (7/10) CAMERA REC/PB @¡ IC2204 $º (R2300) 3.0Vp-p 20.0MHz @™ IC2204 %£ (X2201, R2262) 3.0Vp-p 32.767kHz HI CONTROL 4-71 4-72 4-73 4-74 VI-151 (7/10)
Page 87 DCR-TRV890E/TRV900/TRV900E DCR-TRV890E/TRV900/TRV900E For schematic diagram • Refer to page 4-91 for printed wiring board. VI-151 BOARD (8/10) CAMERA REC/PB @£ IC2401 1 (X2400) 2.5Vp-p 20.0MHz MECHANISM CONTROL 4-76 4-77 4-78 VI-151 (8/10)
Page 88 DCR-TRV890E/TRV900/TRV900E DCR-TRV890E/TRV900/TRV900E For schematic diagram • Refer to page 4-91 for printed wiring board. • Refer to page 4-87 for FP-594 flexible board. VI-151 BOARD (9/10) CAMERA REC/PB @¢ #º IC2503 4 IC2503 ^º 2.6Vp-p 2.8Vp-p 6.7msec 1.1msec @∞ #¡...
Page 89 DCR-TRV890E/TRV900/TRV900E For schematic diagram • Refer to page 4-91 for printed wiring board. DC/DC CONVERTER 4-83 4-84 4-85 4-86 VI-151 (10/10)
Page 90 DCR-TRV890E/TRV900/TRV900E FP-594 (LOADING MOTOR, S/T REEL SENSOR) PRINTED WIRING BOARD — Ref. No.: FP-594 Board; 9,000 Series — FP-594 BOARD M902 LOADING MOTOR SENSOR S903 MODE SW Q901 Q902 TAPE END TAP E TOP S901 C IN S902 REC.P CN901...
Page 91 DCR-TRV890E/TRV900/TRV900E VI-151 BOARD (SIDE A) VI-151 (REC/PB AMP, TIMING GENERATOR, VIDEO INTERFACE, DCT/IDCT, IR TRANSMITTER, AUDIO PROCESSOR, HI CONTROL, MECHANISM CONTROL, DRUM/CAPSTAN MOTOR DRIVE, DC/DC CONVERTER) PRINTED WIRING BOARD C1401 C3244 Q3205 C-8 R2416 C-6 — Ref. No. VI-151 Board; 10,000 Series —...
Page 92 DCR-TRV890E/TRV900/TRV900E VI-151 (REC/PB AMP, TIMING GENERATOR, VIDEO INTERFACE, DCT/IDCT, IR TRANSMITTER, AUDIO PROCESSOR, VI-151 BOARD (SIDE B) HI CONTROL, MECHANISM CONTROL, DRUM/CAPSTAN MOTOR DRIVE, DC/DC CONVERTER) PRINTED WIRING BOARD C1400 A-17 C2016 C-19 C3219 D-13 L1401 A-17 Q3247 E-12 R1857 A-15...
Page 93: Stereo Mic Amp
DCR-TRV890E/TRV900/TRV900E FP-21 (FOCUS SW) FLEXIBLE BOARD MA-333 (STEREO MIC AMP) PRINTED WIRING BOARD RI-10 (SIRCS RECEIVER) PRINTED WIRING BOARD — Ref. No. MA-333 Board; 10,000 Series — — Ref. No. RI-10 Board; 10,000 Series — MA-333 BOARD RI-10 BOARD FP-21 FLEXIBLE BOARD...
Page 94 DCR-TRV890E/TRV900/TRV900E DCR-TRV890E/TRV900/TRV900E STEREO MIC AMP SIRCS RECEIVER 4-99 4-100 4-101 MA-333 RI-10...
Page 95 DCR-TRV890E/TRV900/TRV900E FP-16 (PANEL SWITCH) FLEXIBLE BOARD FP-16 FLEXIBLE BOARD S002 S001 (PANEL CLOSE) (PANEL REV) FP-16 1-670-983- FP-18 (USER CONTROL) FLEXIBLE BOARD FP-18 FLEXIBLE BOARD FP-18 FK-4880 (USER CONTROL) FP-17 FP-23 (S-Y/C IN/OUT) FP-18 (USER CONTROL) For LED FP-16 FP-11...
Page 96 DCR-TRV890E/TRV900/TRV900E CK-80 (USER CONTROL) PRINTED WIRING BOARD ED-48 (USER CONTROL) PRINTED WIRING BOARD — Ref. No. CK-80 Board; 10,000 Series — — Ref. No. ED-48 Board; 10,000 Series — CK-80 BOARD BT7200 C-10 R7213 E-11 C7200 E-10 R7214 E-10 C7200...
Page 97 DCR-TRV890E/TRV900/TRV900E FP-23 (S VIDEO) FLEXIBLE BOARD JK-163 (AUDIO/VIDEO IN/OUT) PRINTED WIRING BOARD — Ref. No. JK-163 Board; 10,000 Series — JK-163 BOARD FP-23 FLEXIBLE BOARD INTELLIGENT ACCESSORY SHOE C7100 FB715 C7101 FB716 C7102 FB717 C7103 FB718 C7104 J7100 CN7100 B-2...
Page 98 DCR-TRV890E/TRV900/TRV900E For schematic diagram • Refer to page 4-121 for PD-101 printed wiring board. • Refer to page 4-121 for FP-19 flexible board. PD-101 BOARD (1/2) CAMERA REC/PB IC5502 8 0.3Vp-p IC5502 9 0.2Vp-p IC5502 !º 0.22Vp-p IC5502 @º 4.2Vp-p IC5502 @™...
Page 99 DCR-TRV890E/TRV900/TRV900E DCR-TRV890E/TRV900/TRV900E PD-101 BOARD (2/2) CAMERA REC/PB IC5601 @§ 16.7MHz 3.5Vp-p IC5601 #¢ 3.5Vp-p !º IC5601 #¶ 2.8Vp-p !¡ IC5602 7 5.6Vp-p TIMING GENERATOR, BACK-LIGHT 4-118 4-119 4-120 PD-101 (2/2)
Page 100: User Control) Flexible Board
DCR-TRV890E/TRV900/TRV900E PD-101 (RGB DRIVER, TIMING GENERATOR, BACK-LIGHT) PRINTED WIRING BOARD — Ref. No. PD-101 Board; 10,000 Series — PD-101 BOARD C5501 C5706 R5501 A-5 R5623 C-4 R5682 D-4 C5502 R5502 A-5 R5624 C-4 R5683 D-4 C5503 CN5601 D-4 R5503 A-5...
Page 101: Color Evf) Printed Wiring Board
DCR-TRV890E/TRV900/TRV900E VF-121 (COLOR EVF) PRINTED WIRING BOARD — Ref. No. VF-121 Board; 10,000 Series — VF-121 BOARD C5001 C5113 Q5101 R5045 C5002 C5114 Q5102 R5046 C5003 C5115 Q5103 R5047 C5004 C5116 R5101 C5005 C5117 R5001 R5102 C5006 C5118 R5003 R5103...
Page 102 DCR-TRV890E/TRV900/TRV900E VF-121 BOARD CAMERA REC/PB !º !¡ IC5001 8 IC5001 9 IC5001 !º IC5001 @º IC5001 @™ IC5001 @¢ IC5101 !∞ IC5102 @¶ IC1502 #∞ IC5102 $¡ IC1502 $∞ 0.2Vp-p 2.7Vp-p 0.28Vp-p 0.18Vp-p 2.8Vp-p 3.0Vp-p 7.6Vp-p 7.6Vp-p 11.0Vp-p 7.6Vp-p 3.0Vp-p 16.4MHz...
Page 103: Evf Back-Light
DCR-TRV890E/TRV900/TRV900E LB-55 (EVF BACK-LIGHT) PRINTED WIRING BOARD — Ref. No. LB-55 Board; 10,000 Series — LB-55 BOARD C5201 C5202 C5203 C5204 C5206 C5207 C5208 CN5201 CN5202 D5201 L5201 L5202 ND5201 E-4 Q5201 R5201 R5202 T5201 For printed wiring boards LB-55 (EVF BACK-LIGHT) •...
Page 104: Adjustments
DCR-TRV890E/TRV900/TRV900E SECTION 5 ADJUSTMENTS 5-1. CAMERA SECTION ADJUSTMENT NTSC model : DCR-TRV900 PAL model : DCR-TRV890E/TRV900E 1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) 1-1-1. List of Service Tools • Oscilloscope • Regulated power supply • Vectorscope • Color monitor • Digital voltmeter Ref.
Page 105: Preparations
1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Note 2: When performing only the adjustments, the lens block and boards need not be disassembled. Pattern box 1) Connect the equipment for adjustments according to Fig. 5-1- 2) The front panel block (MA-333 board, focus ring, focus switch, ND filter switch, microphone unit) must be assembled because the focus ring and ND filter switch are used for adjustments.
Page 106 Viewfinder Note: Press the battery switch using adhesive tape,etc. LCD WINDOW To ED-48 board. To VF-121 board CN5001 Lens block Need not be connected. Must be connected when performing the EVF system adjustments. Regulated power supply (Note) (8.4 ± 0.1Vdc) Must be connected when performing the camera system or LCD system adjustments.
Page 107: Precaution
1-1-3. Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette. POWER switch (FK-4880 block) ......CAMERA FOCUS switch (FP-21) ......... MANUAL DEMO MODE (Menu display) ........OFF 10. BACK LIGHT (ED-48 board) ......... OFF DIGITAL ZOOM (Menu display) ........
Page 108: Initialization Of F, E Page Data
1-2. INITIALIZATION OF F, E PAGE DATA Initial value Address Remark NTSC 1. Initializing the F, E Page Data Fixed data-1 Note: If the F, E page data is initialized, the following adjustments must (Initialized data) be performed again. 1) Modification of F, E PAGE Data 2) Camera system adjustments 27MHz origin osc.
Page 109 Initial value Initial value Address Address Remark Remark NTSC NTSC PAL Fixed data-2 Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-2 Fixed data-1 (Modified data, copy the data built in (Initialized data) the same model.) Fixed data-1...
Page 110 Initial value Initial value Address Remark Address Remark NTSC PAL NTSC PAL Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 (Modified data, copy the data built in the same model.) Table. 5-1-1 Fixed data-1 Fixed data-2 (Modified data, copy the data built in the same model.)
Page 111 4. E Page table Initial value Address Remark Note 1: Fixed data-1 : Initialized data. (Refer to “1. Initializing the F, E NTSC Page Data”.) Fixed data-1 Fixed data-2 : Modified data. (Refer to “2. Modification of F, E PAGE Data”). (Initialized data) Initial value Address...
Page 112 Initial value Address Remark NTSC PAL Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data) 9C to FF Table. 5-1-2...
Page 113: Camera System Adjustments
1-3. CAMERA SYSTEM ADJUSTMENTS Processing after Completing Adjustments 1) Select page: 6, address: 94, and set data: 00. Before perform the camera system adjustments, check that the 2) Select page: 6, address: 95, and set data: 00. specified value of “Composite Output Y Level Adjustment” and 3) Select page: 6, address: 01, set data: 00, and press the PAUSE “Composite Output Chroma Level Adjustment”...
Page 114: Offset Adjustment
3. Offset Adjustment Adjust so that the AGC OUT potential lies within the specified value of the digital clamp. Subject Not required Measurement Point DDS display data of LCD or TV monitor (Note 1) Measuring Instrument Adjustment Page Adjustment Address 2D, 2E, 2F Specified Value 50 to B0...
Page 115: Flange Back Adjustment
4. Flange Back Adjustment The inner focus lens flange back adjustment is carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing. 4-1. Flange Back Adjustment(1) 4-2. Flange Back Adjustment (2) Perform this adjustment after performing “Flange Back Adjustment Subject Flange back adjustment chart (1)”.
Page 116: Flange Back Check
5. Flange Back Check 6. Picture Frame Setting Subject Siemens star Subject Color bar chart standard picture frame (2.0 m from the front of the lens) (95cm from the front of the lens) (Luminance: 300 ± 50 lux) Measurement Point Video output terminal Measurement Point Check operation on TV monitor...
Page 117: Pre White Balance Data Input
7. Pre White Balance Data Input 8. Auto White Balance Standard Data Input At 3200k, input the pre white balance standard data. At 3200K, input the white balance standard data. Subject Clear chart Subject Clear chart (Color bar standard picture frame) (Color bar standard picture frame) Adjustment Page Adjustment Page...
Page 118: Max Gain Adjustment
9. MAX GAIN Adjustment 10. LV Standard Data Input Setting the minimum illumination. Adjust the normal coefficient of the light value. If it is not consistent, the image level required for taking subjects in Subject Clear chart low illuminance will not be produced (dark). (Color bar standard picture frame) Subject Clear chart...
Page 119: White Balance Nd Filter Compensation Adjustment
11. White Balance ND Filter Compensation Adjustment 12. Auto White Balance Adjustment Compensate the white balance deviation when ND filter is ON. Adjust to the proper auto white balance output data. If it is not correct, auto white balance and color reproducibility will Subject Clear chart be poor.
Page 120: Color Reproduction Adjustment (Nd Filter Off)
13. Color Reproduction Adjustment (ND Filter OFF) 14. Color Reproduction Adjustment (ND Filter ON) When the ND filter is off, adjust the color difference matrix When the ND filter is on, adjust the color difference matrix coefficient so that proper color reproduction is produced. coefficient so that proper color reproduction is produced.
Page 121: White Balance Check
15. White Balance Check Subject Clear chart (Color bar standard picture frame) Filter Filter C14 for color temperature correction ND filter 1.0 and 0.3 Measurement Point Video output terminal Measuring Instrument Vectorscope Specified Value Fig. 5-1-11. A to C Fig. 5-1-11 (A) Checking method: 1.0mm 1) Check that the lens is not covered with either filter.
Page 122: Psd Sensor Gain Adjustment
16. PSD Sensor Gain Adjustment Adjust the gain of the PSD sensor for steady shot operation. 16-1. PSD Sensor Gain Adjustment (1) Subject Pattern A (1.5m from the front of the lens) Measurement Point Video output terminal Measuring Instrument Oscilloscope (V period) Adjustment Page Adjustment Address...
Page 123: Psd Sensor Gain Adjustment (2)
16-2. PSD Sensor Gain Adjustment (2) Subject Pattern B (1.5m from the front of the lens) Measurement Point Video output terminal Measuring Instrument Oscilloscope (H period) Adjustment Page Adjustment Address Black Pattern B White White Falling edge of Falling edge of A4 size (297mm ×...
Page 124: Angular Velocity Sensor Sensitivity Adjustment
17. Angular Velocity Sensor Sensitivity Adjustment • This adjustment is performed only when replacing the angular velocity sensor. Although this adjustment need not be performed when the circuit is damaged, etc., check the operations. • Note down the sensitivity displayed on the angular velocity sensor of the repair parts.
Page 125: Color Electronic Viewfinder System Adjustment
1-4. COLOR ELECTRONIC VIEWFINDER 1. VCO Adjustment (VF-121 board) Set the VCO free-run frequency. If deviated, the EVF screen will be SYSTEM ADJUSTMENT blurred. Note 1: The back light (fluorescent tube) is driven by a high voltage AC power supply. Therefore, do not touch the back light holder to Mode VTR stop avoid electrical shock.
Page 126: Bright Adjustment (Vf-121 Board)
2. Bright Adjustment (VF-121 board) 3. Contrast Adjustment (VF-121 board) Set the level of the VIDEO signal for driving the LCD to the specified Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated value.
Page 127: Backlight Consumption Current Adjustment (Vf-121 Board)
4. Backlight Consumption Current Adjustment 5. White Balance Adjustment (VF-121 board) (VF-121 board) Correct the white balance. Set the backlight luminance and color temperature. If deviated, the reproduction of the EVF screen may degenerate. If deviated, the image may become dark or bright. Mode Camera Mode...
Page 128: Lcd System Adjustment
1-5. LCD SYSTEM ADJUSTMENT 1. VCO Adjustment (PD-101 board) Set the VCO free-run frequency. If deviated, the LCD screen will Note 1: The back light (fluorescent tube) is driven by a high voltage AC power supply. Therefore, do not touch the back light holder to be blurred.
Page 129: D Range Adjustment (Pd-101 Board)
2. D range Adjustment (PD-101 board) 3. Bright Adjustment (PD-101 board) Set the D range of the RGB decoder used to drive the LCD to the Set the level of the VIDEO signal for driving the LCD to the specified specified value.
Page 130: Contrast Adjustment (Pd-101 Board)
4. Contrast Adjustment (PD-101 board) 5. V-COM Level Adjustment (PD-101 board) Set the level of the VIDEO signal for driving the LCD to the specified Set the common electrode drive signal level of LCD to the specified value. If deviated, the screen image will be blackish or saturated value.
Page 131: V-Com Adjustment (Pd-101 Board)
6. V-COM Adjustment (PD-101 board) 7. White Balance Adjustment (PD-101 board) Set the DC bias of the common electrode drive signal of LCD to the Correct the white balance. specified value. If deviated, the LCD screen color cannot be reproduced. If deviated, the LCD display will move, producing flicker and Mode Camera...
Page 132: Mechanism Section Adjustment
5-2. MECHANISM SECTION ADJUSTMENT On the mechanism section adjustment For details of mechanism section adjustments, checks, and replacement of mechanism parts, refer to the separate volume “DV MECHANICAL ADJUSTMENT MANUAL C Mechanism ”. 2-1. HOW TO ENTER RECORD MODE WITHOUT 2-3.
Page 133: Video Section Adjustments
5-3. VIDEO SECTION ADJUSTMENTS NTSC model : DCR-TRV900 PAL model : DCR-TRV890E/TRV900E 3-1. PREPARATIONS BEFORE ADJUSTMENTS Use the following measuring instruments for video section adjustments. 3-1-1. Equipment Required TV monitor Oscilloscope (dual-phenomenon, band above 30 MHz with delay mode) (Unless specified otherwise, use a 10 : 1 probe.) Frequency counter Pattern generator with video output terminal.
Page 134: Precautions On Adjusting
3-1-2. Precautions on Adjusting Note 1: Setting the “Forced VTR Power ON” mode (VTR mode) The adjustments of this unit are performed in the VTR mode 1) Select page: 0, address: 01, and set data: 01. or camera mode. 2) Select page: D, address: 10, set data: 02, and press the PAUSE To set to the VTR mode, set the power switch to “VTR”...
Page 135: Adjusting Connectors
RF MON Table 5-3-1. Remove the CPC cover 3-1-4. Connecting the Equipment Connect the measuring instruments as shown in Fig. 5-3-2, and perform the adjustments. VTR recording mode (Except DCR-TRV890E) Pattern generator VIDEO (Yellow) Video output Adjustment (75 Ω )
Page 136: Alignment Tapes
3-1-6. Alignment Tapes Use the alignment tapes shown in the following table. Use tapes specified in the signal column of each adjustment. Name Tracking standard (XH2-1) Tape path adjustment SW/OL standard (XH2-3) Switching position adjustment Audio operation check Audio system adjustment (XH5-3 (NTSC), XH5-3P (PAL)) System operation check Operation check...
Page 137: Initialization Of B, C, D
3-2. INITIALIZATION OF B, C, D PAGE DATA Initial value Address Remark NTSC 1. Initializing the C Page Data Fixed data-1 Note: If the page C data is initialized, the following adjustments must be (Initialized data) performed again. 1) Modification of C page data Switching position adj.
Page 138 Initial value Initial value Address Remark Address Remark NTSC NTSC Fixed data-1 Fixed data-1 (Initialized data) PLL f final adj. Fixed data-1 Fixed data-2 (Initialized data) Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1...
Page 139: Initializing The D
4. Initializing the D Page Data Initial value Address Remark Note: If the D page data is initialized, the following adjustments must be NTSC PAL performed again. Fixed data-2 1) Modification of D page data 2) Video system adjustments 3) Color electronic viewfinder system adjustments Fixed data-1 4) LCD system adjustments Fixed data-2...
Page 140 Initial value Initial value Address Remark Address Remark NTSC NTSC Fixed data-2 Fixed data-1 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-2 Fixed data-1 Fixed data-1 (Initialized data)
Page 141: Initializing The B
9. B Page Table Initial value Address Remark NTSC Note 1: Fixed data-1 : Initialized data. ( Refer to “7. Initializing the B Fixed data-1 Page Data”.) Bright adj.(LCD) Fixed data-2 : Modified data. (Refer to “8. Modification of B PAGE Data”).
Page 142 Address Remark Address Remark Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data)
Page 143 Address Remark Address Remark Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) E0 to FF Table. 5-3-4 5-40...
Page 144: System Control System Adjustment
3-3. SYSTEM CONTROL SYSTEM ADJUSTMENT 1. Battery End Adjustment (VI-151 board) Set the battery end voltage. If the voltage is incorrect, the life of the battery will shorten. The image at the battery end will also lose synchronization. Mode Camera recordings Subject Arbitrary Measurement Point...
Page 145: Inserting A Cassette
3-4. SERVO AND RF SYSTEM ADJUSTMENT 3. PLL f & LPF f Adjustment (VI-151 board) Before performing the servo and RF system adjustments, check that Mode VTR stop the specified value of “27 MHz Master Oscillator Adjustment” of Measurement Point Display data of page: 3, address: 03 “CAMERA SYSTEM ADJUSTMENT”...
Page 146: Switching Position Adjustment (Vi-151 Board)
4. Switching Position Adjustment (VI-151 board) 5. AGC Center Level Adjustment (VI-151 board) Mode VTR playback Mode Camera record and playback Signal SW/OL reference tape (XH2-3) Subject Arbitrary Pin @º of CN2904 (RF MON) (Note 1) Measurement Point Display data of page: 3, address: 03 Measurement Point Measuring Instrument Adjustment remote commander...
Page 147: Apc & Aeq Adjustment (Vi-151 Board)
6. APC & AEQ Adjustment (VI-151 board) 7. PLL f & LPF f Final Adjustment (VI-151 board) Mode Camera record and playback Mode VTR playback Subject Arbitrary Signal Arbitrary Pin @º of CN2904 (RF MON) (Note 1) Measurement Point Measurement Point Display data of page: 3, address: 03 Measuring Instrument Oscilloscope...
Page 148: Video System Adjustments
3-5. VIDEO SYSTEM ADJUSTMENTS 2. S VIDEO OUT Y Level Adjustment (VI-151 Board) Before perform the video system adjustments, check that the specified value of “27 MHz Origin Oscillation Adjustment” of Mode Camera “CAMERA SYSTEM ADJUSTMENT” is satisfied. Subject Arbitrary Measurement Point Y signal terminal of S VIDEO jack 3-5-1.
Page 149: S Video Out Chroma Level Adjustment (Vi-151 Board)
3. S VIDEO OUT Chroma Level Adjustment 4. AV OUT Y, Chroma Level Check (VI-151 Board) (VI-151 Board) Mode Camera Mode Camera Subject Arbitrary Subject Arbitrary Measurement Point Chroma signal terminal of S VIDEO Measurement Point Video terminal of AUDIO/VIDEO jack (75 Ω...
Page 150: Pll Adjustment (Vc-208 Board)
5. PLL Adjustment (VC-208 Board) (Except DCR-TRV890E) Set the VCO center level of the video input circuit (IC1200). Mode VTR stop Signal Color bar (Video terminal of AUDIO/ VIDEO jack input) Measurement Point Display data of page: 3, address: 04...
Page 151: Bist Check
3-5-2. BIST Check 1. Playback System Check 1-1. Preparation for Playback 1-3. IC1601(TFD) BIST(PB) Check 1) Set the POWER switch to VTR (or PLAYER) position. 1) Select page: 3, address: 40, set data: 0F, and press the PAUSE button. 2) Connect the adjusting remote commander and set the HOLD switch to ON (SERVICE) position.
Page 152: Ic1800 (Sfd) Bist (Pb) Check
1-4. IC1600(SFD) BIST(PB) Check 1-5. IC1501(VFD) BIST(PB) Check Select page: 0, address: 01, and set data: 01. Select page: 0, address: 01, and set data: 01. Select page: C, address: AC, set data: 21, and press the PAUSE Select page: C, address: 60, set data: 06, and press the PAUSE button.
Page 153 • UPY Cr BIST(PB) Check • ENC Yb BIST(PB) Check 14) Select page: 3, address: 10, set data: 89, and press the PAUSE 30) Select page: 3, address: 10, set data: 8C, and press the PAUSE button. button. 15) Select page: 3, address: 12, set data: 10, and press the PAUSE 31) Select page: 3, address: 12, set data: 10, and press the PAUSE button.
Page 154: Recording System Check
2. Recording System Check 10) When the recording system from IC1501(VFD) to IC1600(SFD) is normal, the display data (combination data) 2-1. Preparations for recording of page: 3, address: 1A and 1B agrees with any combination as Playback the BIST check tape.(XH5-6(NTSC), XH5-6P(PAL)) shown below.
Page 155: Ic1900(Trx) Bist(Rec) Check
13) Select page: 3, address: 40, set data: 01, and press the PAUSE button. 14) Select page: 3, address: 40, set data: 00, and press the PAUSE button. 15) When the recording system from IC1601 (TFD) to IC1900 (TRX) is normal, the display data (combination data) of page: 3, address: 43 and 44 agrees with any combination as shown below.
Page 156: Ir Transmitter Adjustments
3-6. IR TRANSMITTER ADJUSTMENTS 2. IR Video Deviation Adjustment (VI-151 board) Mode VTR stop Adjust using a IR receiver jig (J-6082-383-A). Signal Arbitrary Measurement Point VIDEO OUT terminal of IR receiver jig Switch setting: (Terminated at 75 Ω) LASER LINK ........ON (Red LED is lit) Measuring Instrument Oscilloscope 1.
Page 157: Ir Audio Deviation Adjustment (Vi-151 Board)
3. IR Audio Deviation Adjustment (VI-151 board) Mode VTR stop Signal Video : No signal Audio : –400Hz, –7.5dBs, Audio left and right terminal of AUDIO/VIDEO jack Measurement Point AUDIO L terminal and AUDIO R terminal of IR receiver jig (Terminated at 47kΩ) Measuring Instrument Audio level meter...
Page 158: Audio System Adjustments
3-7. AUDIO SYSTEM ADJUSTMENTS [Connection of Audio System Measuring Devices] Connect the audio system measuring devices as shown in Fig. 5-3-13. Main unit Recording (Camera mode) 600 Ω Audio oscillator Left Right Attenuator 600 Ω : 270 Ω (1-249-410-11) + 330 Ω (1-249-411-11) Playback Main unit TV monitor...
Page 159: Playback Level Check
1. Playback Level Check 4. Overall Noise Level Check Mode VTR playback Mode Camera recording and playback Signal Alignment tape: Signal No signal: Insert a shorting plug in the For audio operation check MIC jack (XH5-3 (NTSC)) Measurement Point Audio left or right terminal of AUDIO (XH5-3P (PAL)) VIDEO jack Measurement Point...
Page 160: Service Mode
5-4. SERVICE MODE 4-1. ADJUSTMENT REMOTE COMMANDER 2. Precautions upon using the adjustment remote commander The adjustment remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The Mishandling of the adjustment remote commander may erase the correct adjustment data at times.
Page 161: Data Process
4-2. DATA PROCESS The calculation of the DDS display and the adjustment remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data.
Page 162: Service Mode
4-3. SERVICE MODE 2-1. EMG Code (Emergency Code) 1. Setting the Test Mode Codes corresponding to the errors which occur are written in Page D Address 10 addresses 38, 3C and 40. The type of error indicated by the code are shown in the following table.
Page 163: Msw Code
2-2. MSW Code MSW when errors occur: Information on MSW (mode SW) when errors occur MSW when movement starts: Information on MSW when movements starts when the mechanism position is moved (When the L motor is moved) MSW of target of movement: Information on target MSW of movement when the mechanism position is moved Mechanical Position ←...
Page 164: Bit Value Discrimination
3. Bit value discrimination 4. Switch check (1) Bit values must be discriminated using the display data of the Page 2 Address 43 adjustment remote commander for following items. Use the table below to discriminate if the bit value is “1” or “0”. Function When bit value=1 When bit value=0...
Page 165: Switch Check (2)
5. Switch check (2) Page 2 Address 60 to 67 Using method: 1) Select page: 2, address: 60 to 67. 2) By discriminating the display data, the pressed key can be discriminated. Data Address 00 (00 to 0A) 19 (0B to 24) 32 (25 to 44) 59 (45 to 6E) 85 (4F to 9F)
Page 166: Repair Parts List
DCR-TRV890E/TRV900/TRV900E SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number The components identified by mark ! or have some differences from the original one.
Page 167: Mechanism Frame Section
6-1-2. MECHANISM FRAME SECTION Mechanism block (See page 6-11 to 6-13) V I - - 7 5 - 2 0 Lens assembly (See Page 6-10) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-968-729-51 SCREW (M2), LOCK ACE, P2 A-7094-030-A VI-151 BOARD, COMPLETE (890E) 3-052-621-01 CUSHION, LENS A-7094-068-A VI-151 BOARD, COMPLETE (900/900E)
Page 168: Cabinet (L) Section
6-1-3. CABINET (L) SECTION supplied - 1 6 104 103 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-948-339-01 SCREW 0-NO. +P2 TAPPING B2 1-475-949-21 SWITCH BLOCK, CONTROL (FK4880) 3-051-902-01 SHEET METAL, JK (900,900E) 1-670-979-11 FP-11 FLEXIBLE BOARD 1-475-949-31 SWITCH BLOCK, CONTROL (FK4880)(890E) A-7073-677-A JK-163 BOARD, COMPLETE 3-051-904-01 FRAME, FK...
Page 169: Cabinet (R) Section
6-1-4. CABINET (R) SECTION not supplied - 8 0 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks * 151 3-051-920-01 LID, LCD HINGE * 161 3-051-906-01 HOLDER, SP 1-670-981-21 FP-13 FLEXIBLE BOARD 3-051-913-01 STAND 3-052-482-01 EJECTOR, CARD 3-968-729-71 SCREW (M2), LOCK ACE, P2 * 154 3-051-918-01 COVER, PM...
Page 170: Lcd Panel Section
6-1-5.LCD PANEL SECTION supplied supplied not supplied - 1 0 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-051-921-01 COVER (FRONT), HINGE X-3949-004-1 CABINET (C) ASSY, P(900) X-3948-944-1 HINGE ASSY X-3949-046-1 CABINET (C) ASSY, P(900E:AEP,UK) 1-670-983-21 FP-16 FLEXIBLE BOARD X-3949-062-1 CABINET (C) ASSY, P(890E) 3-051-922-01 COVER (REAR), HINGE X-3949-063-1 CABINET (C) ASSY, P(900E:E,HK,AUS,JE,CN)
Page 171: Battery Panel Section
6-1-6. BATTERY PANEL SECTION not supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-051-905-01 SHEET METAL (LOWER), STRAP 3-051-950-01 CLAW, BT LOCK 1-694-411-11 TERMINAL BOARD, BATTERY 3-968-729-71 SCREW (M2), LOCK ACE, P2 X-3949-001-1 PANEL ASSY, BATTERY 1-785-247-11 CONNECTOR, DC-IN 3-948-339-01 SCREW, TAPPING B2 3-051-915-01 PLATE, DC FIXED...
Page 172: Cabinet (Upper) Section
6-1-7. CABINET (UPPER) SECTION supplied EVF assembly (See Page 6-8) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-968-729-01 SCREW (M2), LOCK ACE, P2 * 311 3-051-894-01 RETAINER, SLIDER 3-968-729-51 SCREW (M2), LOCK ACE, P2 * 312 3-051-893-01 RETAINER, LCD 1-670-984-11 FP-17 FLEXIBLE BOARD A-7093-972-A PANEL BLOCK ASSY, INDICATION...
Page 173: Evf Section
6-1-8.EVF SECTION Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-7073-683-A LB-55 BOARD, COMPLETE 3-968-729-01 SCREW (M2), LOCK ACE, P2 1-670-987-21 FP-20 FLEXIBLE BOARD 3-051-896-01 CABINET (UPPER), EVF * 353 3-988-563-01 ILLUMINATOR (458), BL X-3948-951-1 CUP ASSY, EYE 3-989-416-01 CUSHION (458), LCD 3-713-791-01 SCREW (M1.7X5), TAPPING, P2 8-753-023-51 LCX027AK-1...
Page 174: Front Panel Section
6-1-9. FRONT PANEL SECTION S702 not supplied S700 PH700 PH701 S701 - 3 3 D7402 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-3948-950-1 GRILLE ASSY, MICROPHONE X-3948-949-1 RETAINER ASSY, MF 1-418-014-11 MICROPHONE UNIT X-3948-954-1 RETAINER ASSY, ND 3-051-926-01 LID, MICROPHONE * 419 3-051-887-01 RETAINER, JACK...
Page 175: Lens Block Section
6-1-10. LENS BLOCK SECTION supplied not supplied supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-051-924-01 FRAME, LENS 3-713-791-61 SCREW (M1.7X7), TAPPING, P2 3-948-339-01 SCREW, TAPPING B2 A-7073-676-A CD-202 BOARD, MOUNT 1-758-174-11 LENS, ZOOM (VCL-4312VA) X-3948-953-1 COVER (R) ASSY, PRISM 3-709-428-01 MOTOR, FOCUS A-7030-948-A PRISM ASSY (INCLUDE 3CCD)(890E/900E)
Page 176: Cassette Compartment, Drum And Reel Table Assembly
6-1-11. CASSETTE COMPARTMENT, DRUM AND REEL TABLE ASSEMBLY M901 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-988-312-01 SPRING, EXTENSION X-3948-445-1 TABLE (T) ASSY, REEL 3-988-220-01 BRAKE (T) X-3948-444-1 TABLE (S) ASSY, REEL 3-988-221-01 GEAR (T), BRAKE 3-989-465-01 WASHER, STOPPER 3-988-222-01 SPRING (T), BRAKE 3-988-298-01 SPRING EXTENSION...
Page 177: Tape Guide, Pinch Slider Assembly And Brake Slider Assembly
6-1-12. TAPE GUIDE, PINCH SLIDER ASSEMBLY AND BRAKE SLIDER ASSEMBLY Included in Ref No. on page 6-13. Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-988-263-01 GEAR, RELAY 3-988-258-01 SPRING (GLT), TORSION X-3948-442-2 GEAR ASSY, GOOSENECK 3-988-253-01 SPRING (GLS), TORSION X-3948-435-2 PLATE ASSY, TG1 ADJUSTMENT X-3948-440-1 ARM (T) ASSY, GL...
Page 178: Each Gears And Loading/Capstan Motor Assembly
6-1-13. EACH GEARS AND LOADING / CAPSTAN MOTOR ASSEMBLY M903 S903 Q901 D901 Q902 H901 H902 CN901 S902 M902 not supplied S901 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-988-274-01 PULLEY, CONVERSION 3-988-223-01 ARM, EJECT 3-988-276-02 BELT, TIMING 3-988-224-01 ARM, PINCH PRESS 3-988-216-01 GEAR, CAM...
Page 179: Electrical Parts List
CD-202 CK-80 6-2. ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • RESISTORS When indicating parts by reference number, parts list may be different from the parts All resistors are in ohms. please include the board name. specified in the diagrams or the components METAL: metal-film resistor The components identified by mark ! or...
Page 180 CK-80 FP-21 FP-594 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < RESISTOR > A-7073-684-A ED-48 BOARD, COMPLETE ********************* R7200 1-216-809-11 METAL CHIP 1/16W (Ref.No.:10,000Series) R7201 1-216-864-11 METAL CHIP 1/16W R7202 1-216-833-11 METAL CHIP 1/16W < CONNECTOR > R7203 1-216-833-11 METAL CHIP 1/16W...
Page 181 JK-163 LB-55 MA-333 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-7073-677-A JK-163 BOARD, COMPLETE A-7073-683-A LB-55 BOARD, COMPLETE ********************** ********************* (Ref.No.:10,000Series) (Ref.No.:10,000Series) < CAPACITOR > < CAPACITOR > C7100 1-162-964-11 CERAMIC CHIP 0.001uF C5201 1-162-970-11 CERAMIC CHIP 0.01uF C7101 1-162-964-11 CERAMIC CHIP...
Page 182 R7345 1-216-834-11 METAL CHIP 1/16W R7347 1-216-839-11 METAL CHIP 1/16W < DIODE > R7348 1-216-818-11 METAL CHIP 1/16W D7300 8-719-061-82 DIODE TLSU1002(TPX1,SONY) R7350 1-216-837-11 METAL CHIP 1/16W D7304 8-719-064-61 DIODE 01BZA8.2(TE85L) R7351 1-216-849-11 METAL CHIP 220K 1/16W D7305 8-719-420-14 DIODE MA8082-TX...
Page 183 MA-333 PD-101 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R7360 1-216-841-11 METAL CHIP 1/16W < DIODE > R7361 1-216-815-11 METAL CHIP 1/16W R7363 1-216-848-11 METAL CHIP 180K 1/16W D5602 8-713-102-80 DIODE 1T369-01-T8A ************************************************************ D5604 8-719-422-31 DIODE MA8047-M-TX ! D5704 8-719-404-49 DIODE MA111-TX A-7073-679-A PD-101 BOARD, COMPLETE...
Page 184 PD-101 RI-10 SE-75 VC-208 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R5541 1-218-941-11 RES,CHIP 1/16W R5805 1-218-965-11 RES,CHIP 1/16W R5542 1-218-941-11 RES,CHIP 1/16W R5807 1-218-990-11 SHORT R5601 1-218-990-11 SHORT R5603 1-218-990-11 SHORT < TRANSFORMER > R5604 1-218-990-11 SHORT ! T5701...
Page 185 VC-208 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C206 1-107-682-11 CERAMIC CHIP C359 1-162-958-11 CERAMIC CHIP 270PF C207 1-125-777-11 CERAMIC CHIP 0.1uF C360 1-164-942-11 CERAMIC CHIP 0.0068uF 10% C208 1-125-777-11 CERAMIC CHIP 0.1uF C361 1-164-942-11 CERAMIC CHIP 0.0068uF 10% C209 1-125-777-11 CERAMIC CHIP...
Page 186 VC-208 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C702 1-107-820-11 CERAMIC CHIP 0.1uF C1216 1-125-777-11 CERAMIC CHIP 0.1uF C703 1-104-851-11 TANTAL. CHIP 10uF C1217 1-164-943-11 CERAMIC CHIP 0.01uF C705 1-107-820-11 CERAMIC CHIP 0.1uF C1218 1-164-943-11 CERAMIC CHIP 0.01uF C721 1-164-935-11 CERAMIC CHIP...
Page 187 VC-208 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks IC208 8-759-387-31 IC TC75S55F(TE85R) < TRANSISTOR > IC300 8-752-392-06 IC CXD3116R-T6 IC301 8-759-445-93 IC AK6440AM-E2 Q200 8-729-037-74 TRANSISTOR UN9213J-(K8).SO IC302 8-752-896-42 IC CXP912032-078R (890E) Q201 8-729-042-58 TRANSISTOR UN9111J-(K8).SO IC302 8-752-897-31 IC CXP912032-089R-T6 (900/900E)
Page 188 VC-208 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R216 1-218-957-11 RES,CHIP 2.2K 1/16W R373 1-218-977-11 RES,CHIP 100K 1/16W R217 1-208-712-11 RES,CHIP 0.50% 1/16W R374 1-208-939-11 RES,CHIP 150K 0.50% 1/16W R218 1-208-683-11 RES,CHIP 0.50% 1/16W R375 1-208-939-11 RES,CHIP 150K 0.50% 1/16W...
Page 189 VC-208 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R530 1-218-985-11 RES,CHIP 470K 1/16W R775 1-218-977-11 RES,CHIP 100K 1/16W R531 1-218-985-11 RES,CHIP 470K 1/16W R776 1-218-977-11 RES,CHIP 100K 1/16W R532 1-218-957-11 RES,CHIP 2.2K 1/16W R777 1-218-977-11 RES,CHIP 100K 1/16W R533...
Page 190 VC-208 VF-121 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < VIBRATOR > < DIODE > X200 1-767-586-21 VIBRATOR, CRYSTAL (27MHz) D5101 8-719-043-70 DIODE MA6S121-(TX) X300 1-767-450-11 VIBRATOR, CERAMIC D5102 8-713-102-80 DIODE 1T369-01-T8A X751 1-781-069-21 VIBRATOR,LITHIUM NIOBATE (6.875MHz) X1200 1-781-068-21 VIBRATOR, CRYSTAL (40,5MHz) (900/900E) <...
Page 191 VF-121 VI-151 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R5109 1-218-973-11 RES,CHIP 1/16W C1436 1-135-149-21 TANTALUM CHIP 2.2uF R5110 1-218-974-11 RES,CHIP 1/16W C1437 1-125-777-11 CERAMIC CHIP 0.1uF R5111 1-218-965-11 RES,CHIP 1/16W C1438 1-164-943-11 CERAMIC CHIP 0.01uF R5113 1-218-979-11 RES,CHIP...
Page 192 VI-151 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C1881 1-164-935-11 CERAMIC CHIP 470PF C2056 1-164-943-11 CERAMIC CHIP 0.01uF C1884 1-164-943-11 CERAMIC CHIP 0.01uF C2206 1-107-820-11 CERAMIC CHIP 0.1uF C1885 1-125-777-11 CERAMIC CHIP 0.1uF C2210 1-107-820-11 CERAMIC CHIP 0.1uF C1886 1-125-777-11 CERAMIC CHIP...
Page 193 VI-151 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C2579 1-125-777-11 CERAMIC CHIP 0.1uF C3251 1-135-259-11 TANTAL. CHIP 10uF 6.3V C2582 1-125-777-11 CERAMIC CHIP 0.1uF C3252 1-135-259-11 TANTAL. CHIP 10uF 6.3V C2583 1-107-686-11 TANTAL. CHIP 4.7uF C3253 1-104-851-11 TANTAL.
Page 194 VI-151 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks D3212 8-719-066-16 DIODE RB491D-T146 L1811 1-414-754-11 INDUCTOR 10uH D3213 8-719-027-77 DIODE MA796-TX L2004 1-414-754-11 INDUCTOR 10uH D3214 8-719-066-34 DIODE RB461F-T106 L2005 1-414-754-11 INDUCTOR 10uH D3215 8-719-066-34 DIODE RB461F-T106 L2201 1-414-754-11 INDUCTOR 10uH D3216...
Page 195 VI-151 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks Q2007 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO Q3234 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO Q2008 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO Q3235 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO Q2009 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO Q3236 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO Q2011 8-729-037-63 TRANSISTOR UN9115J-(K8).SO Q3237 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO Q2012...
Page 196 VI-151 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R1432 1-218-965-11 RES,CHIP 1/16W R1695 1-218-938-11 RES,CHIP 0.50% 1/16W R1433 1-218-953-11 RES,CHIP 1/16W R1696 1-208-707-11 RES,CHIP 0.50% 1/16W R1434 1-218-965-11 RES,CHIP 1/16W R1697 1-208-707-11 RES,CHIP 0.50% 1/16W R1435 1-218-950-11 RES,CHIP 1/16W...
Page 197 VI-151 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R2066 1-218-965-11 RES,CHIP 1/16W R2271 1-216-791-11 METAL CHIP 1/16W R2201 1-218-953-11 RES,CHIP 1/16W R2272 1-218-961-11 RES,CHIP 4.7K 1/16W R2203 1-218-953-11 RES,CHIP 1/16W R2273 1-218-959-11 RES,CHIP 3.3K 1/16W R2204 1-218-953-11 RES,CHIP 1/16W...
Page 198 VI-151 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R2434 1-218-977-11 RES,CHIP 100K 1/16W R2905 1-218-961-11 RES,CHIP 4.7K 1/16W R2436 1-218-977-11 RES,CHIP 100K 1/16W R2906 1-218-990-11 SHORT R2439 1-218-977-11 RES,CHIP 100K 1/16W R2907 1-218-990-11 SHORT R2440 1-218-977-11 RES,CHIP 100K 1/16W...
Page 199 VI-151 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R3258 1-218-965-11 RES,CHIP 1/16W MISCELLANEOUS R3259 1-208-719-11 RES,CHIP 0.50% 1/16W ************* R3260 1-208-715-11 RES,CHIP 0.50% 1/16W R3261 1-218-965-11 RES,CHIP 1/16W 1-670-982-11 FP-14 FLEXIBLE BOARD R3262 1-218-989-11 RES,CHIP 1/16W 1-670-976-21 FP-8 FLEXIBLE BOARD 1-670-980-11 FP-12 FLEXIBLE BOARD...
Page 200 Ref. No. Part No. Description Remarks ACCESSORIES ************ 1-475-599-11 ADAPTOR, AC (AC-L10) 1-475-950-21 REMOTE COMMANDER (RMT-811) (900,900E) 1-475-950-31 REMOTE COMMANDER (RMT-812) (890E) 1-569-007-11 ADAPTOR, CONVERSION 2P (900:JE/900E:JE) 1-569-008-21 ADAPTOR, CONVERSION 2P 1-573-291-11 CONNECTOR, CONVERSION 21-PIN (890E/900E:AEP,UK) 1-690-827-12 CORD SET, POWER (INCLUDE NOISE FILTER) (890E:AEP/900E:AEP) 1-696-819-11 CORD, POWER (900E:AUS) 1-759-671-11 ADAPTOR, FLOPPY DISK...
Page 201 You can find the parts position of location of mount locations applying to VC-208 board of a set. VC-208 SIDE A DCR-TRV890E/TRV900/TRV900E IC752 V C - 2 0 8 S I D E B D C R - T R V 8 9 0 E / T R V 9 0 0 / T R V 9 0 0 E 〈PARTS REFERENCE SHEET〉...
Page 202 〈 〉 FOR CAMERA COLOR REPRODUCTION ADJUSTMENT Take a copy of CAMERA COLOR REPRODUCTION FRAME and Parts referencesheets with a clear sheet for use. DCR-TRV890E/TRV900/TRV900E — 301 —...
Page 203 DCR-TRV890E/TRV900/TRV900E Sony Corporation 98H1648-1 Printed in Japan ©1998.8 Personal A&V Products Company 9-974-107-11 Published by Quality Engineering Dept. — 302 — (Osaki East)
Page 204 Applicable serial Nos. (for the item 2.) • Abbreviation Models Serial Nos. Models Serial Nos. CND: Canadian model DCR-TRV890E : AEP 1003922 and higher DCR-TRV900E : AEP 1020501 and higher HK : Hong Kong model -TRV890E : UK 1004001 and higher...
Page 205 < > : Page No. shown in < > indicates the page to refer on this Supplement-1. [ ] : Page No. shown in [ ] indicates the page to refer on the original Service Manual : Added portion. DCR-TRV890E/TRV900/TRV900E. [ Page: 3-5 ] 3-2.
Page 206 DCR-TRV890E/TRV900/TRV900E PS-422 (DC IN) PRINTED WIRING BOARD < > : Page No. shown in < > indicates the page to refer on this Supplement-1. — Ref. No. PS-422 Board; 10,000 Series — PS-422 BOARD LB-55 (EVF BACK-LIGHT) C3500 Q3500 F-1...
Page 207 DCR-TRV890E/TRV900/TRV900E [ ] : Page No. shown in [ ] indicates the page to refer on the original Service Manual DCR-TRV890E/TRV900/TRV900E. [ Page: 4-90 ] VI-151 BOARD (SIDE A) VI-151 (REC/PB AMP, TIMING GENERATOR, VIDEO INTERFACE, DCT/IDCT, IR TRANSMITTER, AUDIO PROCESSOR,...
Page 208 DCR-TRV890E/TRV900/TRV900E VI-151 (REC/PB AMP, TIMING GENERATOR, VIDEO INTERFACE, DCT/IDCT, IR TRANSMITTER, AUDIO PROCESSOR, VI-151 BOARD (SIDE B) HI CONTROL, MECHANISM CONTROL, DRUM/CAPSTAN MOTOR DRIVE, DC/DC CONVERTER) PRINTED WIRING BOARD C1400 A-17 C2016 C-19 C3220 C-12 L1605 A-17 R1400 A-18 R1877 B-15...
Page 209 DCR-TRV890E/TRV900/TRV900E < > : Page No. shown in < > indicates the page to refer on this Supplement-1. [ ] : Page No. shown in [ ] indicates the page to refer on the original Service Manual : Changed portion.
Page 210 : Added portion. [ Page: 6-2 ] 6-1-2. MECHANISM FRAME SECTION V I - - 2 0 Ref. No. Part No. Description Remarks A-7094-030-B VI-151 BOARD, COMPLETE (890E) A-7093-973-B VI-151 BOARD, COMPLETE (900/900E) 1-959-893-11 HARNESS (PV-127) (US,Canadian model) 6-2. ELECTRICAL PARTS LIST : Chenged portion.
Page 211 Added portion Page Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-7074-018-A PS-422 BOARD, COMPLETE < TRANSISTOR > *********************** (Ref.No.:10,000Series) Q3500 8-729-024-48 TRANSISTOR 2SK1830-TE85L Q3501 8-729-036-43 TRANSISTOR HAT1023R-EL < CAPACITOR > Q3502 8-729-036-43 TRANSISTOR HAT1023R-EL Q3503 8-729-804-41 TRANSISTOR 2SB1122-S C3500 1-164-227-11 CERAMIC CHIP 0.022uF 10% 16V...
Page 212 , ∗ : Chenged portion. : Added portion. : Deleted portion. Page VI-151 BOARD (4/10) 4-63 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C1610 1-164-933-11 CERAMIC CHIP 220PF 10% 16V C1610 6-26 C1611 1-164-858-11 CERAMIC CHIP 22PF C1611 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V...
Page 213 Page 3. C Page Table Remark Address Initial value NTSC PAL Fixed data-1 5-35 Fixed data-2 Data IC1602 of VI-151 board CXD3200R-T6 SN104266PN-TEB Fixed data-1 (Initialized data) 3-5-2. BIST Check 1-4. IC1600(SFD) BIST(PB) Check Select page: 0, address: 01, and set data: 01. Select page: C, address: AC, set data: 21, and press the PAUSE button.
Page 214 : Added portion. : Changed portion. [ Page: 6-9 ] 6-1-9. FRONT PANEL SECTION not supplied (Include 429) D7402 Ref. No. Part No. Description Remarks A-7094-505-A RING ASSY, MF 3-719-845-01 SCREW (B2X4), TAPPING — 19 —...
Page 215 DCR-TRV890E/TRV900/TRV900E Sony Corporation 99D1648-1 Printed in Japan ©1999.4 Personal A&V Products Company 9-974-107-82 Published by Quality Engineering Dept. — 20 — (Shinagawa)

This manual is also suitable for:

Dcr-trv900 Dcr-trv900e

Sony DCR-TRV890E Service Manual

Service Note

Self-Diagnosis Function

Adjustments

Repair Parts List

Quick Links

Related Manuals for Sony DCR-TRV890E

Summary of Contents for Sony DCR-TRV890E

This manual is also suitable for:

Table of Contents