Advertisement
Quick Links
®
with joystick control panel
24 VDC Spot/Flood light
with joystick control panel
INSTALLATION AND OPERATION
READ THESE INSTRUCTIONS BEFORE
INSTALLING AND USING THIS PRODUCT.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
MODEL 502-2
24 VDC Spotlight
MODEL 503-2
INSTRUCTIONS
IMPORTANT!
®
.
Advertisement
Related Manuals for Guest 502-2
Summary of Contents for Guest 502-2
- Page 1 ® ® MODEL 502-2 24 VDC Spotlight with joystick control panel MODEL 503-2 24 VDC Spot/Flood light with joystick control panel INSTALLATION AND OPERATION INSTRUCTIONS IMPORTANT! READ THESE INSTRUCTIONS BEFORE INSTALLING AND USING THIS PRODUCT. KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE...
- Page 2 Description The GUEST 502-2 Spotlight uses a 100 watt halogen bulb to produce a tightly focused beam which can illuminate objects up to 1 mile away. The GUEST 503-2 Spot/Flood light uses a revolutionary dual-focus halogen bulb. Select the 100 watt, narrow-beam spotlight for illuminating objects up to 1 mile away or the 55 watt wide-area floodlight for docking and deck lighting.
- Page 3 Installation Mounting the Spotlight 1. Select a flat, smooth surface to mount the light. Be sure that you will have access to the underside of the location, and that you can drill holes there without damaging existing wiring or structures. Avoid locations where lines, anchors, sails or other hazards might cause damage to the light.
- Page 4 7. Fasten the light securely to the mounting surface using four 1/4" diameter (6mm) bolts, large flat washers, lock washers and nuts. Do not over tighten. 8. Install the gray 5-wire (model 502-2) or 6-wire (Model 503-2) cable between the light and the planned location of the control panel. Avoid running the cable across sharp edges or where it may be exposed to extreme heat.
- Page 5 3. Bring the 5-wire (Model 502-2) or 6-wire (Model 503-2) cable coming from the spotlight out through the control panel, and make the connections as shown on pages 4 and 5 for your model light. 4. Feed the spliced cable back into the cutout hole. Test fit the control panel and use a pencil to mark the locations of the two small holes in the panel onto the mounting surface.
- Page 6 Connect control wires to SAME Do not use wire colors of provided cable blue wires 10 Amp Fuse 24 volts DC Black (included) 24 volts DC Note: The blue control wire is not used with Model 502-2...
- Page 7 503-2 Spot/Floodlight Wiring Diagram Foam Gasket 10-12 ga. (5mm) crimp Connector 24 volts DC 10 Amp Fuse Black (or circuit breaker) 24volts DC Connect cable wires from spotlight to SAME wires colors of provided cable Male Plugs on this end of cable Connect cable control wires to SAME wire colors of provided cable 10 Amp Fuse...
- Page 8 OPERATE THE MODEL 502-2 or 503-2. Troubleshooting Under normal use, your Guest Beamer spotlight will provide you with many years of reliable service. If your unit should become damaged by a severe impact, we recommend that you return the unit to our factory for reconditioning.
- Page 9 If the lower motor makes no sound when it is activated, replace the lower motor. If your light has a problem that is not described above, return the unit to the Guest Service Department for a inspection. Be sure to include a brief description of the problem, proof of purchase (if requesting warranty service), and your daytime telephone and/or fax number.
-
Page 10: Customer Service
LIMITED WARRANTY For one (1) year from the date of purchase, The Guest Co., Inc. will, at its discretion, repair or replace for the original consumer, free of charge, any part or parts found upon examination by Guest Co., Inc., 95 Research Parkway, Meriden, Connecticut to be defective in material or workmanship or both.