Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Ashly PE-Series
Summary of Contents for Ashly PE-Series
- Page 1 PE-Series Amplifier Operating Manual Ashly Audio Inc. 847 Holt Road, Webster, NY 14580-9103 Toll Free (800) 828-6308, Telephone (585) 872-0010, FAX (585) 872-0739 www.ashly.com All Trademarks referred to herein, are the property of their respective owners. All Rights Reserved...
- Page 2 Introduction - 2 Introduction About Ashly Safety Congratulations on your purchase of an Ashly PE-Series (Protea Enabled) amplifier. The PE- The PE Series - 3 Series is made up of high-power, high-efficiency, lightweight amplifiers incorporating the latest Physical Description - 4 in power and control technologies.
-
Page 3: The Pe Series
If the DC condition is severe the amplifier will enter standby. DC Servo - PE-Series has a DC Servo to prevent DC Offset at the output. Over Current Protection - Is controlled in the output stage. -
Page 4: Physical Description
The PE Series - 3 Physical Description - 4 Each model in the PE-Series is 2RU, and weighs under 24 pounds. They all share the same Front Panel physical design. The model number is indicated in the lower left corner of the front panel... -
Page 5: Input Module
Documentation for this module is provided in a separate Measurements - 10 document. If there is an input feature or function you’d like to see developed for the PE-Series, Dimensions - 11 please contact Ashly. -
Page 6: Typical Applications
Connectors & Polarity PE-Series amplifiers utilize several different professional audio connectors. The Euroblock and Screw-Terminal connectors are clearly marked on the amplifier’s rear panel and are straightforward. The connection polarity for the other three types of connectors (XLR, TRS, and Speakon) are less obvious. -
Page 7: Operation
Operator Manual – PE Series Amplifiers Page - 7 Operation Introduction - 2 The PE Series - 3 The amplifier’s On/Off Switch is a rocker-type switch located on the left side of the front panel. Turning on the amplifier initiates start-up by activating the inrush current limiter. During power Physical Description - 4 up, the Clip/Mute, Standby and Protect LEDs from both channels will light up for a few seconds. -
Page 8: Troubleshooting
Reboot computer. If issue is not Failure resolved, consider replacing CAT-5 Cables Comm LED not lit Check connection between amplifier and network. Reboot computer. If issue is not resolved, consider replacing CAT-5 Cables Copyright© 2005 – Ashly Audio Inc. -
Page 9: Spec Table
Operator Manual – PE Series Amplifiers Page - 9 Introduction - 2 Spec Table The PE Series - 3 All Specifications Subject to Change or Improvement Without Notice.) Physical Description - 4 PE-800 PE-1200 PE-1800 PE-2400 PE-3000 PE-3800 Power Output Installation –... - Page 10 Operator Manual – PE Series Amplifiers Introduction - 2 Measurements The PE Series - 3 Physical Description - 4 The following graphs are actual measurements from PE-Series amplifiers during typical use. Installation – 5 Operation – 7 Troubleshooting - 8 Spec Table - 9...
- Page 11 Operator Manual – PE Series Amplifiers Page - 11 Introduction - 2 Amplifier Dimensions The PE Series - 3 All PE Series amplifiers share the same dimensional measurements: Physical Description - 4 Installation – 5 Operation – 7 Troubleshooting - 8 Spec Table - 9 Measurements - 10 Dimensions - 11...
- Page 12 Any implied warranties which may arise under the operation of State law shall be effective only for FIVE years from the date of purchase of the product. Ashly Audio shall be liable only to correct defects in the product itself, and not for any damage or injury which may result from or be incidental to or a consequence of such defect.