Preparation Before Use; Dry Operation; Temporary Operation; Remote Control - Toshiba RAS-18SKCV Series Owner's Manual

PREPARATION BEFORE USE

2
Preparing Filters
1. Open the air inlet grille and remove the air fi lters.
2. Attach the fi lters. (see detail in the accessory sheet).
Loading Batteries
1. Remove the battery cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Clock Setup
•
1. Push CLOCK by tip of the pencil.
If timer indication is fl ashing, go to the next step 2.
OFF
ON
2. Press or : adjust the time.
3. Press : Set the time.
SET
Remote Control Reset
1. Remove the batteries.
2. Press .
3. Insert the batteries.
3 AIR FLOW DIRECTION
FIX
1
Press : Move the louver in the
desired vertical direction.
SWING
2
Press : Swing the air
automatically and press again to stop.
3
For horizontal direction, adjust manually.
Note:
• Do not move the louver manually by others.
• The louver may automation positioning by some operation mode.
4

REMOTE CONTROL

1 Infrared signal emitter
2 Start/Stop button
3 Mode select button (MODE)
4 Temperature button (TEMP)
5 Fan speed button (FAN)
6 Swing louver button (SWING)
7 Set louver button (FIX)
8 On timer button (ON)
9 Off timer button (OFF)
! Sleep timer button (SLEEP)
" Setup button (SET)
# Clear button (CLR)
$ Memory and Preset button (PRESET)
% One-Touch button (ONE-TOUCH)
& High power button (Hi-POWER)
( Power selection button (POWER-SEL)
) Quiet button (QUIET)
~ Comfort sleep button (COMFORT SLEEP)
+ Filter reset button (FILTER)
, Clock Reset button (CLOCK)
- Check button (CHK)
5 ONE-TOUCH
Press the "ONE-TOUCH" button for fully automated operation that is customized
to the typical consumer preferences in your region of the world. The customized
settings control temperature air fl ow strength, air fl ow direction and other settings
to provide you alternate contact with "ONE-TOUCH" of the button. If you prefer
other settings you can select from the many other operating functions of your
Toshiba unit.
ONE-TOUCH
Press : Start the operation.

AUTOMATIC OPERATION

6
To automatically select cooling or fan only operation
MODE
1. Press : Select A.
2. Press TEMP : Set the desired temperature.
1110650131_01EN.indd 2 1110650131_01EN.indd 2
COOLING / FAN ONLY OPERATION
7
MODE
1. Press
TEMP
2. Press
Cooling: Min. 17°C, Fan Only: No temperature indication
FAN
3. Press
HIGH
8

DRY OPERATION

For dehumidifi cation, a moderate cooling performance is controlled automatically.
1. Press
2. Press
9 Hi-POWER OPERATION
To automatically control room temperature and airfl ow for faster cooling operation
(except in DRY and FAN ONLY mode)
Hi-POWER
Press
POWER-SELECTION OPERATION
10
This function is used when its circuit breaker is shared with other electrical
appliances. It limits the maximum current/ power consumption to 100%, 75%
or 50%. The lower the percentage, the higher the saving and also the longer
the compressor lifetime.
POWER-SEL
Press
• When the level is selected, PWR-SEL level fl ashes on LCD display for 3
seconds. In case of 75% and 50% level, number "75" or "50" also fl ashes
for 2 seconds.
• Due to the reason that POWER SELECT FUNCTION limits the maximum
current, inadequate cooling capacity may occur.
11

TEMPORARY OPERATION

In case of the misplaced or discharged remote control
• Pressing the RESET button, the unit can start or
stop without using the remote control.
• Operation mode is set on AUTOMATIC operation,
preset temperature is 24°C and fan operation is
automatic speed.
12

TIMER OPERATION

PRESET FAN
TEMP
Set the timer when the air conditioner is operating.
ONE-TOUCH MODE
Setting the ON Timer
COMFORT
QUIET SLEEP
1
Press
SWING FIX Hi-POWER POWER-SEL
2
TIMER CLR Press
ON OFF
SLEEP SET
CHK FILTER CLOCK
3 Press
Daily timer allows the user to set both the ON & OFF timers and will be
activated on a daily basis.
Setting Everyday Timer
1
Press
2
Press
• During the every day timer is activating, both arrows ( , ) are indicated.
Note:
• Keep the remote control in accessible transmission to the indoor unit;
otherwise, the time lag of up to 15 minutes will occur.
• The setting will be saved for the next same operation.
: Select Cool or Fan only .
: Set the desired temperature.
: Select AUTO, LOW , LOW+ , MED
.
MODE
: Select Dry .
TEMP
: Set the desired temperature.
: Start and stop the operation.
: Select (for 100%), (for 75%), (for 50%)
Setting the OFF Timer
ON OFF
: Set the desired ON timer. Press : Set the desired OFF timer.
: Set the timer. Press : Set the timer.
SET SET
: Cancel the timer. Press : Cancel the timer.
CLR
CLR
3
ON Press .
: Set the ON timer. SET
Press
SET
4
OFF
: Set the OFF timer.
( or ) mark fl ashing.
, MED+ , or
: button during the
10/7/09 1:40:53 PM 10/7/09 1:40:53 PM