Related Manuals for Kenmore 90117
Summary of Contents for Kenmore 90117
- Page 1 Use & Care Guide Model: 90117 Kenmore ®/MD Liquid Propane Gas Grill P/N G314-001-030801 Sears Canada Inc. Toronto, ON., M5B 2C3 www.sears.ca ™ Model 466724711 • Nov-29-10...
-
Page 2: For Your Safety
DANGER WARNING CALIFORNIA PROPOSITION 65 If you smell gas: 1. Combustion by-products produced when using this 1. Shut off gas to the appliance. product contain chemicals known to the State of 2. Extinguish any open flame. California to cause cancer, birth defects, and other reproductive harm. -
Page 3: Table Of Contents
(or Kenmore Grill Warranty......3 replacement if repair proves impossible). -
Page 4: Use And Care
LP Tank USE AND CARE • The LP Tank used with your grill must meet the following requirements: DANGER • Use LP Tanks only with these required measurements: 12" (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) capacity maximum. - Page 5 LP Tank Exchange Connecting Regulator To The LP Tank • Many retailers that sell grills offer you the option of 1. LP tank must be properly secured onto grill. (Refer to replacing your empty LP tank through an exchange service. assembly section.) Use only those reputable exchange companies that inspect, precision fill, test and certify their tanks.
- Page 6 Leak Testing Valves, Hose and Regulator 1. Turn all grill control knobs to OFF. 2. Be sure regulator is tightly connected to LP tank. 3. Completely open LP tank valve by turning OPD hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately.
- Page 7 Safety Tips WARNING Before opening LP cylinder valve, check the coupling nut for tightness. When grill is not in use, turn off all control knobs and LP cylinder valve. For Safe Use of Your Grill and to Avoid Serious Never move grill while in operation or still hot. Injury: Use long-handled barbecue utensils and oven mitts to •...
-
Page 8: Use And Care
Burner Flame Check WARNING • Remove cooking grates and flame tamers. Light burners, rotate knobs from HI to LOW. You should see a smaller flame in LOW position than seen on HI. Perform burner Turn controls and gas source or tank OFF when not flame check on sideburner, also. -
Page 9: Spider Alert
3. Remove carryover tubes and burners. CAUTION 4. Detach electrode from burner. NOTE: Removal/Detachment method will depend on the burner configuration. See different configurations in illustrations below. SPIDER ALERT! 5. Carefully lift each burner up and away from valve openings. We suggest three ways to clean the burner tubes. - Page 10 Indirect Cooking How To Tell If Meat Is Grilled Thoroughly Poultry and large cuts of meat cook slowly to perfection on • Meat and poultry cooked on a grill often browns very fast the grill by indirect heat. Place food over unlit burner(s); the on the outside.
-
Page 11: Parts List
PARTS LIST Key Qty Description Part # Key Qty Description Part # BACK RAIL G314-0806-W1 SIDEBURNER GRID G314-2204-W1 RIGHT LEG ASSEMBLY G314-2100-W2 4 CONTROL KNOB G432-0010-W1 LEFT LEG ASSEMBLY G314-0900-W2 3 HEAT DIFFUSER G314-0303-W1 MATCH HOLDER G401-0079-W1 SWING AWAY GRATE G314-0002-W1 FRONT PANEL G314-0805-W1... -
Page 12: Parts Diagram
PARTS DIAGRAM 12 • 466724711... -
Page 13: Assembly
ASSEMBLY Place rear rail between cart frames. Hook the key hole slots to the preassembled #10-24x1/2” machine screws. Tighten the screws. Right Leg Assembly Back Rail Left Leg Assembly Front Panel Insert axle rod into wheel, legs other wheel. Attach with (1) axle spacer and hitch pin. Insert leg extenders into right legs. - Page 14 Hook the short tank exclusion wire (silver) onto front right leg. Flex tank exclusion wire to fit other end to the hole on bottom edge of rear rail. Rear Rail Front Right Leg Short Tank Exclusion (sliver) Hook the long tank exclusion wire ( black ) onto front left leg.
- Page 15 This step requires two people to lift and position grill head onto cart. Carefully lower the grill head onto the cart. Make sure the regulator hose is hanging outside the cart. Slide grill head from front to rear of cart until the pre-installed screws are slide into the opening of the metal tabs. Tighten the pre-installed screws.
- Page 16 Place left side shelf to left side of firebox . Make sure the key hole slots are fit onto the pre-installed screws (A). Tighten the pre-installed screws (B). Position sideburner valve behind fascia , attach with #8-32X3/8” screws. Qty: 2 8-32X3/8”...
- Page 17 Place sideburner into shelf (A). Make sure to insert valve into sideburner tube. Attach sideburner with (1) flat washer and wing nut. Under sideburner shelf, install sideburner clip to sideburner tube and valve. Attach sideburner ignitor wire to electrode as shown (B). Sideburner Flat Washer Wing Nut...
- Page 18 Place control knobs onto valve stems. Control Knobs Place heat tents over burners by inserting tabs into slots in front of firebox. Opposite ends of heat tents rest on pins in back of firebox. 18 • 466724711...
- Page 19 Place cooking grates onto grate rests. Insert ends of Swing Away pivot wire into holes in sides of grill lid. Insert ends of Swing Away leg wire into holes in sides of firebox. NOTE: Pivot and leg wires, running side-to-side, should be under wires running front-to-back. If pivot and leg wires are on top, Swing Away is installed upside-down.
- Page 20 Insert tank retainer wire into left legs. Rotate tank retainer wire inward toward cart. Tank Retainer Set bottom of tank into notches of tank bracket. Tank collar opening must face to front of grill, lean tank inward and engage tank collar with tank wire. LP CYLINDER IS SOLD SEPARATELY.
-
Page 21: Troubleshooting
EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Emergencies Possible Cause Prevention/Solution Gas leaking from • Damaged hose. • Turn off gas at LP cylinder or at source on natural gas systems. If cracked/cut/burned anything but burned, replace valve/hose/regulator. -
Page 22: Troubleshooting
Troubleshooting (continued) Problem Possible Cause Prevention/Solution Burner(s) will not light PIEZO PUSH-BUTTON AND ROTARY: using ignitor. • Push-button sticks at bottom. • Replace ignitor. • Rotary knob rotates without clicking. • Replace knob. • Sparking between ignitor and electrode. • Inspect wire insulation and proper connection. Replace wires if insulation is broken. - Page 23 NOTES 466724711 • 23...