Sharp AR-5316 Service Manual page 19

Main Sub
Contents
code code
06 02 Resist roller solenoid operation
check
10 Cassette semi-circular roller
cleaning
08 01 Developing bias output
02 Main charger output (Grid = HIGH) When the [START] key is pressed, the main charger output is supplied for 30 sec in the grid voltage
03 Main charger output (Grid = LOW) When the [START] key is pressed, the main charger output is supplied for 30 sec in the grid voltage
06 Transfer charger output
21 1 Maintenance cycle setting
22 01 Maintenance counter display
04 Jam total counter display
05 Total counter display
08
SPF counter display
13 CRUM destination display
When the [START] key is pressed in the sub code input state, the resist solenoid (RRS) turns ON for
500ms and OFF for 500ms. This operation is repeated 20 times.
After completion of the process, the machine goes into the sub code input standby mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input
standby mode. When [CA] key is pressed, the simulation is terminated.
First of all, remove the developer unit.
Enter the simulation code, specify the cassette to be cleaned with the tray select key, and press
START button. The main motor rotates to move the cassette semi-circular roller by half circle and
make the roller face downward.
After completion of cleaning, when INTERRUPT key is pressed, the machine goes into the sub code
entry standby mode and the roller returns to the original positions.
To clean another roller continuously, press INTERRUPT key to return the roller to the original
position, and execute the simulation again.
During the operation, the sub code is displayed on the display.
* When CA key is pressed, the simulation mode is terminated.
However, the roller returns to the original position by the initial operation.
When the [START] key is pressed, the developing bias signal is turned ON for 30 sec.
However, to calculate the actual output value is calculated, execute SIM25-01.
After completion of the process, the machine goes into the sub code input standby mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input
standby mode. When [CA] key is pressed, the simulation is terminated.
HIGH mode. After completion of the process, the machine goes into the sub code input standby
mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input
standby mode. When [CA] key is pressed, the simulation is terminated.
LOW mode. After completion of the process, the machine goes into the sub code input standby
mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input
standby mode. When [CA] key is pressed, the simulation is terminated.
Select an output mode with the [Mode select] key and press the [START] key. The transfer charger
output is delivered for 30 sec in the selected mode.
After 30 sec of transfer charger output, the machine goes into the sub code entry standby mode.
When [INTERRUPT] key is pressed during the process, the machine goes into the sub code input
standby mode. When [CA] key is pressed, the simulation is terminated.
Display lamp
AE mode lamp
AE mode lamp & PHOTO mode lamp
AE & TEXT & PHOTO mode lamp
•Small size is Letter R (A4R) or smaller.
The current set maintenance cycle code is displayed (initial display), and the set data are stored.
Code
0
1
The maintenance counter value is displayed. (Alternate display by 3 digits)
The jam total counter value is displayed. (Alternate display by 3 digits)
The total counter value is displayed. (Alternate display by 3 digits)
The SPF counter value is displayed. (Alternate display by 3 digits)
When this simulation is executed, the CRUM destination set (written) in the CRUM chip is displayed.
If the display does not match the destination code saved in the CRUM chip, it is judged as an error.
*This simulation is valid only for the models where the CRUM is valid.
7-seg display Meaning (CRUM destination)
00 Not set yet
01 BTA-A
02 BTA-B
03 BTA-C
AR-5316 SIMULATIONS 7-3
Details of operation
Normal size width: Front surface
Small size width: Front surface
Manual paper feed mode
Setting
150,000 sheets * Default
Free (999,999 sheets)
7-seg display
04
12
11
Output mode
Meaning (CRUM destination)
BTA-E
AL series
AR-5316(for SEC)