Advertisement
1<
if"'!
:Al
'"l"!
,e:
i:::l
'n
,..
1-'
,0
:::s
!_--
:0
i'1i
~n
10
'Q.
i
i3!,
.ll:
',<
:t:r
iQi
In
17>
!
L _
:l
~
,
....
' 0
.0.
Ie:
1:4
I
o~
:::l
G
Remedy
• Make sure the cassette tape has an erase-protection tab when you
record to a cassette tape. If needed, cover the hole with cellophane
tape.
·If you connect the cable to S-VIDEO
OUTI
COMPONENT VIDEO OUT
I
HDMI OUT jack, try connecting it to AUDIO
I
VIDEO OUT jack instead.
• Check if a cassette tape is in this unit.
• No cassette tape is inserted.
• Setup menus cannot be called up during DVD recording and playback.
• The motor may rotate for the duration of approximately 5 minutes for
efficient operation. This is not a malfunction.
• The HDMI sound is not output when "HDMI Audio" is set to "OFF".
• Check the RCA audio cable connection. If you are using HDMI-DVI
conversion cable, you must connect the RCA audio cable, too.
• Check whether the output format of this unit (HDMI FORMAT) matches
the supported input format of other connected device.
• Head cleaning for VCR may be necessary. Refer to "Auto Head Cleaning"
(page 5).
• Adjust tracking control for better picture by pressing [TRACKING
A
I
V]
while you are playing back a cassette tape.
• If there is a power failure or unplugging during recording, finalizing,
formatting or editing (even after "Repairing" disappears), a repairing
process will begin automatically just after turning the unit on again.
It may take several minutes up to about several hours.
·If you intend to cancel the repairing process, press [.OPEN/CLOSE]
on the front panel, then select "Yes" and press [ENTER]. After that, press
[OPEN/CLOSE . ] to take out the disc. The disc canceled during the
repairing process MAY NOT work.
• It may take a few seconds for the disc tray to open after you have
recorded or edited a disc. This is because the unit is adding disc data to
the disc.
• Multi-angles are not recorded on the DVD-video being played back.
• The angle-change operation is whenever possible as long as the disc
contains a multi-angle portion. Actual change will be performed when
the portion has come up.
• The DVD-video prohibits changing angles.
• Try changing the angle using the DVD-video's menu.
·It may take a few seconds for the unit to input disc data before
recording stops.
• Multilingual subtitle are not recorded on the DVD-video.
• The title does not have the multilingual audio tracks.
• The DVD-video prohibits the changing of the language for the sound
track.
• Depending on the disc, you may not be able to do some of the
operations. Refer to the instruction manual supplied with the disc.
• Resume playback was activated (page 59). Press [STOP.] twice.
• You have inserted a disc whose title menu or DVD menu automatically
appears on the TV screen when it is first inserted.
• The DVD-video features an auto playback function.
rR
There is no picture.
The disc tray does not open when you
press [OPEN/CLOSE .]'
In a case you intend to cancel the
repairing process.
--------
Recording does not stop immediately
after you press [STOP .].
The angles cannot be changed.
"Repairing" appears on the TV screen.
I
I
There is no sound or the sound is
distorted.
The cassette tape does not play back.
Picture noise appears.
The motor rotates even when
playback I recording is stopped.
The tape ejected after you press
[RECe].
The remote control does not function.
Some functions such as stop, search,
or slow-motion playback cannot be
performed.
The subtitle language cannot be
changed or turned off.
The language for the sound track
cannot be changed.
The unit starts playing back the disc
automatically.
The disc does not start playback from
the beginning.
Setup menu cannot be called up.
L
~
__
EN 105
Advertisement
