Table of Contents
Advertisement
Quick Links
PANASONIC CONSUMER ELECTRONICS
COMPANY, DIVISION OF MATSUSHITA
ELECTRIC CORPORATION OF AMERICA
One Panasonic Way
Secaucus, New Jersey 07094
World Wide Web Address
http://www.panasonic.com
Printed in U.S.A.
PANASONIC SALES COMPANY, DIVISION
OF MATSUSHITA ELECTRIC OF
PUERTO RICO INC. ("PSC")
Ave. 65 de Infanteria, Km. 9.5
San Gabriel Industrial Park
Carolina, Puerto Rico 00985
Tel. (809) 750-4300 Fax (809) 768-2910
Service Manual
MODEL MC-V210 03
SPECIFICATIONS
Model
Power Source
Power Consumption
Cord Length
Motor Protector
Height Adjust
Weight
Specifications are subject to change without notice for further improvement.
2003 PANASONIC HOME AND COMMERCIAL PRODUCTS COMPANY,
DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA
All rights reserved. Unauthorized copying and distribution is a violation of law.
ORDER NO. MAC081803U
E17
Commercial Vacuum Cleaner
MC-V210 03
AC 120V (60 Hz)
10.0 Amps
50 Ft.
Yes
4 Position
16.0 lbs.
Advertisement
Table of Contents
Related Manuals for Panasonic MC-V21003
Summary of Contents for Panasonic MC-V21003
- Page 1 One Panasonic Way PUERTO RICO INC. (“PSC”) Secaucus, New Jersey 07094 Ave. 65 de Infanteria, Km. 9.5 2003 PANASONIC HOME AND COMMERCIAL PRODUCTS COMPANY, San Gabriel Industrial Park World Wide Web Address DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Carolina, Puerto Rico 00985 http://www.panasonic.com...
-
Page 2: Table Of Contents
TROUBLESHOOTING GUIDE WARNING CONDITION CHECKPOINT METHOD OF INSPECTION CAUSE/REMEDY This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise • Power source •... -
Page 3: Specifications
MOTOR FAN REPLACEMENT PICTORIAL WIRING DIAGRAM Removal Tap Down on the 1. Mark the position of the fan case's location on the motor with a pencil, or score 3 Crimped Areas it with a sharp object before disassembly. This will aid you in reassembling the fan case, (Fig. -
Page 4: Exploded View (General Parts)
EXPLODED VIEW MOTOR REPLACEMENT (GENERAL PARTS) Removal 1. Remove the dust cover by grasping the top near the On/Off switch and pulling Screws Motor Case sharply out toward you. 2. Remove the lower plate, agitator assembly, belt, and the nozzle housing as instructed in the respective removal sections. -
Page 5: Exploded View (Nozzle Housing)
POWER CORD/ON-OFF SWITCH REPLACEMENT (Cont.) EXPLODED VIEW (NOZZLE HOUSING)… BLOCK Installation 1. Insert the new power cord (power cord replacement only) into the dust compartment as far as necessary in order to place A-10 a new cord retainer in proper location on power cord. The proper location is approximately one and one eighth inches/thirty A-21 millimeters (1 1/8”/30 mm) of new power cord outer jacket extending past the cord retainer and washer. -
Page 6: Parts List (Nozzle Housing)
PARTS LIST SWITCH COVER AREA WIRING MANAGEMENT (NOZZLE HOUSING)… BLOCK Ref. No. Part Name & Description Part No. Quantity Remarks A – 1 Nozzle Housing ACØ1ABAWZYU2 Furniture Guard Glued On A – 2 Lower Plate Assembly AC91AAEZZVØ6 A – 3 Lower Plate AC27AAEZZVØ6 Includes A-6 Packing... -
Page 7: Exploded View ( Body , Motor Housing, And Motor)
NOZZLE HOUSING REPLACEMENT EXPLODED VIEW (BODY, MOTOR HOUSING, AND MOTOR)… BLOCK Removal 1. Remove the lower plate as outlined in the LOWER PLATE REMOVAL/INSTALLATION section. 2. Remove the belt and agitator assembly as outlined in the respective sections. 3. Remove the hose by pulling up to remove it from the nozzle housing. -
Page 8: Parts List ( Body , Motor Housing, And Motor)
PARTS LIST BRUSH REMOVAL/INSTALLATION (MOTOR HOUSING, MOTOR, HANDLE, AND BODY)... BLOCK Ref. No. Part Name & Description Part No. Quantity Remarks Removal (Fig. 5) C - 1 Dust Compartment Unit AC88KAPNZU11 Incl. C-38, C-44, C-45 & C-46 1. Remove the lower plate as outlined in the LOWER PLATE REMOVAL/ C - 2 ON/OFF Switch AC98EARFZØU... -
Page 9: Exploded View (Motor Fan Assembly)
LOWER PLATE REMOVAL/INSTALLATION EXPLODED VIEW (MOTOR FAN ASSEMBLY) Removal 1. Place the handle in upright position. (Fig. 1) 2. Turn the vacuum cleaner over exposing the underside. Release the lower plate by pressing the two (2) latches that secure it inward, (Fig 1). 3. -
Page 10: Exploded View (Packing Materials)
EXPLODED VIEW COMPONENT REMOVAL CHART (PACKING MATERIALS) COMPONENT TO COMPONENTS THAT HOW TO REMOVE BE REMOVED MUST BE REMOVED Belt Lower Plate Release latches, and tilt off. Agitator Assembly Lift out with end caps. Agitator Assembly Lower Plate Release latches, and tilt off.