AMX Endeleo UDM-1604 Quick Start Manual

Overview
The UDM-1604 4x16 Multi-Format Distribution Hub (FG-UDM-1604) delivers any
video source, including Component, RGB, VGA and S-Video to a virtually unlimited
number of display devices. Advanced, yet cost-effective, it distributes media over
easily-installed, dedicated Cat5, 5e or 6 cable, thereby de-coupling it from the
corporate backbone.
Users can quickly switch and transmit any video source to any display device, power
on/off display devices, and permission user control to select and play video sources
and media servers on demand.
The UDM-1604 (FIG. 1) offers four high-resolution input ports on the back of each unit.
Additional Composite video inputs (RJ-45 located on the front) enable the connection
of four interconnects from a TVM-1600 Managed TV Distribution Hub or four
Composite video sources using approved Video over UTP extenders. In total, the
UDM-1604 system can distribute any combination of the following: four RGBHV
sources, four Component video sources, four S-Video sources or 12 Composite video
sources.
OUTPUT Ports (RJ-45)
IR connections for locally connected devices
Serial port (RJ-12)
ETHERNET port (RJ-45)
FIG. 1
UDM-1604
Features
• 4 multi-format inputs (plus 4 CVBS inputs) x 16 outputs
• Digital audio support
• Central device control
• Compatible with TVM-1600
• 1U rack-mounting
• Cascadable to support higher number of outputs
Compatibility
The UDM-1604 is compatible for use with the UDM-RX01 (FG-UDM-RX01) receiver.

Product Specifications

UDM-1604 Specifications
Power Requirements: 90-264v AC140 W (3 PIN IEC)
Network Interface: 10baseT
Serial Interface: 9600, 8, N, 1
Max Video Input: • 4 x RGBHV (or)
• 4 x S-Video (or)
• 12 x CVBS (plus)
• 4 x Endeleo TVM-1600 or CVBS
Cascade Port: Matrix connector for tertiary units
Electrical: RJ-45 indicating power to receiver and link status.
Operating Environment: • 35°F - 95°F (5°C - 35°C)
• Max. relative humidity - 85% (non-condensing)
Dimensions (HWD): 1 3/4" x 19" x 12 1/2" (45 mm x 440 mm x 320 mm)
Weight: 8.8 lb. (4 Kg)
Certifications: • CE/UL/FCC part 15 Class A
Included Accessories: • IEC power cord
• 19" mounting brackets
• RS-232 DB-9/RJ-12 connection cable
Note: No A/V interface cables supplied
Other AMX Equipment: • HD15 to S-Video Cable (FG-UDM-SVID01)
• HD15 to 3x RCA Breakout Cable (FG-HD15RCA3)
• RS232 DB9/RJ12 Connection Cable (FG-RS01)
• UDM-RX01 Multi-Format Receiver (FG-UDM-RX01)
• UDM-RC10 IR Engineering Remote Control
(FG-UDM-RC10)
• IR01 IR Emitter Module (FG-IR01)
• IR03 External IR Receiver Module (FG-IR03)
UDM-1604
TVM / AV Ports (RJ-45)
Input connections
Endeleo Multi-Format Distribution Hub
Audio & Video Formats/Resolutions/Distance
Audio & Video Formats/Resolutions/Distance
Class Format Name
Composite 720x480 NTSC
720x756 PAL
Component 720x480 480p
720x756 576p
1280x720 720p
1920x1080 1080i
1920x1080 1080p
VGA 640x480 VGA
800x600 SVGA
1024x768 XGA
1280x1024 SXGA
1600x1200 UXGA
A/V Source Input Connectors
There are 4 sets of input connectors to the rear panel of the UDM-1604, labelled A-D
(see FIG. 1) that allow the UDM-1604 to connect to A/V source devices.
Connecting a VGA Video Input
1. Connect one end of a VGA cable to the source device's VGA output port.
2. Attach the other end of the cable to the appropriate VIDEO IN connection on the
UDM. For example, connect to the Video In connection on Input A of the Hub.
3. Connect any audio to the analog (RCA) audio connectors or digital (SPDIF)
connector.
Note: Ensure Input A is configured as a "VGA Input" and named appropriately within
the "Inputs" section of the Configuration software. Also ensure the correct Audio Type
(Analog L/R or S/PDIF) is selected for the relevant input.
Connecting a Composite Video Input
1. Connect the UDM-HD15RCA3 Breakout Cable (FG-HD15RCA3, not included) to
the source device's Composite output ports:
•A1 = red RCA
•A2 = green RCA
•A3 = blue RCA
2. Attach the other end of the cable to the appropriate VIDEO IN connection on the
UDM.
3. Connect any audio to the analog (RCA) audio connectors or digital (SPDIF)
connector.
Connecting a Component Video Input
1. Connect the UDM-HD15RCA3 Breakout Cable (FG-HD15RCA3, not included) to
the video source device's Component video output connectors (Red, Green and
Blue).
2. Attach the other end of the cable to the appropriate VIDEO IN connection on the
UDM.
3. Connect any audio to the analog (RCA) audio connectors or digital (SPDIF)
connector.
Connecting an S-Video Input
1. Connect the UDM-SVID01 HD-15 to SVideo cable (FG-UDM-SVID01, not
included) to the video source's S-Video connection.
2. Attach the other end of the cable to the appropriate VIDEO IN connection on the
UDM.
3. Connect any audio to the analog (RCA) audio connectors or digital (SPDIF) con-
nector.
Device Connectivity (IRTX Ports)
A maximum of 2 Devices such as DVD players or VCRs can be connected to the UDM
Hub and controlled through the Browser software or via a remote control.
1. Connect an Endeleo IR Emitter Module (FG-IR01) to the relevant IRTX port at
the rear of the Hub.
2. Run the other end of the IR Emitter to the device's IR sensor and attach the bud
to the device's sensor by removing the cover of the reverse side of the bud.
IR commands for each device on the system have to be learned by the Hub in order to
function properly. Refer to the Protocols and IR section of the UDM-1604 Operation/
Reference Guide on how to learn a device's IR commands.
IR Receiver (IRRX) Port
The IR RX port has two purposes:
•It is used for devices utilizing Passthrough Mode.
•Also used for learning and creating new IR protocols.
Refer to the UDM-1604 Operation/Reference Guide for details.
Quick Start Guide
Distance (m) Distance (ft.)
700 2300
700 2300
700 2300
700 2300
200 650
150 500
120 400
200 650
200 650
200 650
150 500
120 400