AMX UDM-0808-SIG Quick Start Manual

Overview
The UDM-0808-SIG-SIG Endeleo Signature Series Multi-Format Distribution Hub
(FG1402-01) delivers any video source, including Component, RGB, VGA and
S-Video to display devices. The UDM-0808-SIG (FIG. 1) supports 8 high-resolution
input ports and 8 UDM output ports, and supports delivery of bidirectional serial and IR
to/from remote devices.
Power Status
UDM OUTPUT Ports 1-8 (RJ45)
Input connections
Cascade In/Out
FIG. 1
UDM-0808-SIG
In total, the UDM-0808-SIG can distribute any combination of the following: 8 RGBHV
sources, 8 Component video sources, 8 S-Video sources or 24 Composite video
sources. Source inputs to the UDM are industry standard VGA, Composite,
Component or S-Video feed, and output is presented as an RJ45 port for connection
to Cat5/5e/6/7 twisted-pair Ethernet cable.
Video inputs are connected via the HD15 Input connector on the rear of the UDM.
Adapters are used to bring the different types of video source into the UDM. Each
UDM has an Ethernet network port to provide connectivity to a central management
system. A Serial connection is also provided for CLI administration and diagnostic
purposes.
Features
• 8 multi-format inputs x 8 outputs
• Native NetLinx
• End device control (IR + Serial)
• Digital and Analog audio support
• Cascade output ports allow A/V distribution to other UDM-0808 Hubs, and to
UDM-ABB-8-SIG Audio Breakout Box.
• Cascadable to support higher number of outputs
Compatibility
The UDM-0808-SIG is compatible for use with UDM-RX02N (FG-1402-20) Receivers.
Product Specifications
UDM-0808-SIG Specifications
Power Require- • 3 PIN IEC, 100 to 240Vac 50/60Hz
ments: • Dissipation: 130W
Front Panel Components
LEDs • Power Status bar - Blue light bar on front panel indicates unit
is powered.
• Status LEDs - Eight blue LEDs light to indicate which of the
eight outputs are currently routing video to a connected
UDM-RX02N Receiver.
Rear Panel Components
UDM Output Eight RJ45 ports provide connectivity to up to 8 UDM-RX02N
Ports (1-8): receivers via Cat5/5e/6/7.
A/V Source Input Eight sets of Input connections for up to 8 A/V inputs with the
Connectors following connectors:
(A-H):
• Video (see Video Inputs below)
• Analog audio Left / Right (see Audio Inputs below)
• SPDIF digital audio (see Audio Inputs below)
UDM-0808-SIG
8 Output Port Status LEDs
(front)
Serial port (RJ12)
ETHERNET port (RJ45)
Input connections
Power connector/switch
Endeleo Signature Series Multi-Format Distribution Hub
UDM-0808-SIG Specifications (Cont.)
Video Inputs: HD15 female connector supports the following formats:
VGA
• Component - requires an UDM-HD15RCA3 Breakout Cable
(FG-HD15RCA3, not included)
• S-Video - requires an UDM-SVID01 HD15 to SVideo cable
(FG-UDM-SVID01, not included)
• Composite - requires an UDM-HD15RCA3 Breakout Cable
(FG-HD15RCA3, not included)
Max Video Input:
• 8 x RGBHV (or)
• 8 x S-Video (or)
• 8 x component (or)
• 8 composite inputs
Audio Inputs: • Analog Audio In - RCA female analog audio connectors
(white = Left, red = Right).
• SPDIF Audio In - RCA female digital audio connector
(black).
NETWORK Port: RJ45 Ethernet port provides 100 BaseT network connectivity.
SERIAL Port: RJ12 port allows an administrator to receive debugging and
diagnostic information via RS232.
Note: Serial Interface: 115200, 8, N, 1
CASCADE Ports • Cascade Out and In ports send and receive cascaded A/V
signals to other UDM-0808-SIG Hubs.
(1-4 / 5-8):
• The Cascade Out ports also provide audio-only to an UDM-
ABB-8-SIG Audio Breakout Box.
Note: Depending on the application, up to four Hubs can be
cascaded together.
IEC Power Universal switch-mode power supply.
Connector:
• As a Class 1 appliance the Hub should be connected to a
mains supply with a protective earthing connection.
• On/Off switch is located beside the power connector.
Note: The rating label found on the bottom left of the rear
panel (beneath the IEC connector) contains important infor-
mation applicable to the Hub's installation environment.
Operating • 35°F to 95°F (5°C to 35°C)
Environment: • Max. relative humidity - 85% (non-condensing)
Dimensions: • 3.5" x 19" x 12 1/2" (889 mm x 440 mm x 320 mm)
• 2 RU
Weight: 13.6 lbs. (6.16 kg)
Certifications: • CE
• FCC part 15 Class A
Included • IEC power cord
Accessories: • 19" mounting brackets
• UDM-RC05 IR Remote Control (FG1402-70)
• IR03 External Infrared Receiver Module (FG-IR03)
Note: No A/V interface cables supplied.
Other AMX • HD15 to S-Video Cable (FG-UDM-SVID01)
Equipment: • HD15 to 3x RCA Breakout Cable (FG-HD15RCA3)
• UDM-RX02N Multi-Format Receiver (FG-1402-20)
• UDM-ABB-8-SIG Audio Breakout Box (FG1402-60)
• IR01 IR Emitter Module (FG-IR01)
• UDM-EXP-02 Cascade Cable (FG1402-71)
• RS-232 DB-9/RJ-12 connection cable (FG-RS01)
• 6' Ethernet Crossover Cable
Ethernet 10/100 Base-T RJ-45 Wiring Configuration
The table below describes the pinouts, signals, and pairing for the Ethernet
10/100 Base-T connector and cable.
Ethernet Pinouts and Signals
Pin Signals Connections
1 TX + 1 --------- 1
2 TX - 2 --------- 2
3 RX + 3 --------- 3
4 no connection 4 --------- 4
5 no connection 5 --------- 5
6 RX - 6 --------- 6
7 no connection 7 --------- 7
8 no connection 8 --------- 8
Quick Start Guide
Pairing
1 --------- 2 White-Orange
Orange
3 --------- 6 White-Green
White-Blue
Green
White-Brown
Brown
Color
Blue