Boutside Back Exhaust; Outside Back Exhaust; Remove Blower Plate - Kenmore 316495111 Installation And Operating Instructions Manual

OUTSIDE BACK EXHAUST

B
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B2. Remove Blower Plate
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
IMPORTANT NOTES:
•
Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•
Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
PREPARING THE REAR WALL
B1.
FOR OUTSIDE BACK EXHAUST
You need to cut an opening in the rear wall for
outside exhaust.
NOT E:
IT IS VERY
READ
IN THE AND FOLL IMPO RTAN
INST ALLA OW THE T TO
BEFO TION INST DIRE CTIO
REAR RE PRO CEED NS
WAL L ING WITH RUC TION
This Rear TEM PLAT THIS S
mounti Wall Templa E. 3/8" TO EDGE
ng plate te serves 12"
outlet. and to locate the to positio
1. Use a level horizon n the bottom
accura to check tal exhaus t
2. Locate tely. that the templa
and mark te is positio
  right side of the centerl at least one stud ned   
I t is importa ine. on the 4"
screw mounte nt to use left or  
of the microw d firmly at least   
locatio ns ave. Mark in a stud to suppor one wood      
3. Drill for the two additio t the weight
holes in supplie d toggle nal, evenly      
a stud, drill a 3/16" the marked bolts. spaced
that do hole for locatio ns. Where 
toggle not line up with wood screws there is
  bolts. a stud, drill 5/8" . For holes   
D O NOT holes for 
AT THIS TIME. INSTA LL  
4. Remov THE MOUN TING PLATE 
5. Review e the templa  
installa the Installa te from the rear 
tion situatio tion Instruc wall.
n. tion book for your
Darle vuelta
a la hoja
versió n en Españ para consu
ol. ltar la
 
Loca te 
and mark    
moun ting holes to      
IMPO RTAN plate . align with    
holes in     
LOCA T: the      
TE AT     
THE CEN LEAS T ONE STUD   
TERL INE.
MAR K ON EITH  
THE LOCA ER SIDE      
SPAC ED TOG TION FOR OF
AREA GLE BOLT 2 ADD
. S IN THE ITION AL,
MOU NTIN EVEN LY     
G PLAT E
    

Trim the
rear wall
temp late
along
the dotte
d line.

 Loca te
and mark
moun ting holes to
plate .
IMPO RTAN
T:
LOCA TE AT
THE CEN LEAS T
TERL INE.
MAR K
THE LOCA
SPAC
 ED TOG
AREA . GLE BOLT

•
Read the instructions on the REAR
WALL TEMPLATE.
•
Tape it to the rear wall.
•
Cut the opening, following the instructions of the
REAR WALL TEMPLATE.
Installation Instructions
NOTE: IT IS VERY IMPORTANT
READ AND FOLLOW THE DIRECTIONS
INSTRUCTION S
IN THE INSTALLATION
WITH THIS
BEFORE PROCEEDING
REAR WALL TEMPLATE.
serves to position the bottom
This Rear Wall Template
mounting plate and to locate the horizontal exhaust
outlet.
1. Use a level to check that the template is positioned
accurately. one stud on the left or
2. Locate and mark at least
right side of the centerline.
It is important to use at least one wood
a stud to support the weight
screw mounted firmly in
of the microwave. Mark two additional, evenly spaced
toggle bolts.
locations for the supplied locations. Where there is
3. Drill holes in the marked
a stud, drill a 3/16" hole for wood screws. For holes
a stud, drill 5/8" holes for
that do not line up with
toggle bolts.
DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
Instruction book for your
5. Review the Installation
installation situation.
Darle vuelta a la hoja para consultar la
versión en Español.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT: STUD ON EITHER SIDE
LOCATE AT LEAST ONE
THE CENTERLINE.
FOR 2 ADDITIONAL,
MARK THE LOCATION IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
along the dotted line.
Trim the rear wall template
Trim the
rear wall
temp late
along
the dotte
d line.
align with
holes in
the
ONE STUD
ON EITH
ER SIDE
TION FOR OF
2 ADD
ITION AL,
S IN THE EVEN
MOU NTIN LY
G PLAT
E

(Horizontal Duct)
3/8" TO EDGE
along the dotted line.
Trim the rear wall template
12"
TO
4"
OF
EVENLY
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
STUD ON EITHER SIDE OF
LOCATE AT LEAST ONE
THE CENTERLINE.
FOR 2 ADDITIONAL, EVENLY
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.

REMOVE BLOWER PLATE

B2.
Remove and save the screw that holds the blower
plate to the microwave. Lift off the blower plate.
Blower Plate
EN-16
Back of
Microwave