Kenmore 721.86012 Installation Instructions Manual
Microwave hood combination
Hide thumbs
Also See for 721.86012:
- Use & care manual (46 pages) ,
- Installation instructions manual (21 pages)
Table of Contents
Advertisement
Quick Links
Models/Modelos
721.86012
721.86013
721,86019
Read and save these
installation instructions.
Lea y guarde
estas
instrucciones
de
instalaci6n
iNSTALLATiON
iNSTRUCTiONS
f
INSTRUCCiONES INSTALAGON
I
J
MicrowaveHood Combination
Combinaci6n Microondas C ampana
Part No. MFL57652402
Sears, Roebuck and Co., Hoffman Estates, IL. 60179 U.S.A
www.sears.com.
Advertisement
Table of Contents
Related Manuals for Kenmore 721.86012
Summary of Contents for Kenmore 721.86012
- Page 1 Models/Modelos 721.86012 INSTRUCCiONES INSTALAGON 721.86013 721,86019 MicrowaveHood Combination Read and save these installation instructions. Combinaci6n Microondas C ampana Lea y guarde estas instrucciones instalaci6n Part No. MFL57652402 Sears, Roebuck and Co., Hoffman Estates, IL. 60179 U.S.A www.sears.com.
- Page 2 YOUR SAFETY FIRST BEFORE YOU START * Proper installation is the installer's responsibility! - Read the entire manual before you begin. - The model number label is located on the oven front. See Figure 1. - Mounting plate is located on back side of microwave oven.
- Page 3 YOUR SAFETY FIRST * THiS APPLIANCE MUST BE GROUNDED! - If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape wire for the electric current. This appliance is equipped with a cord having grounding wire with a grounding plug.
- Page 4 YOUR SAFETY FIRST • MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT° = Mount the oven against a fiat, vertical wail, so that it is supported by the wail. The wail should be constructed of minimum 2" x 4" wood studding and 3/8"...
-
Page 5: In The Box
PART , TOOL , MATERIAL5 THE FOLLOWING PARTS ARE SUPPLIED WiTH THE OVEN: NOTE: Depending on your ventilation requirements, you may not use all of these parts. Damper/duct connector One power cord clamp (for roof vented or wall vented installation) One dark-colored mounting screw... - Page 6 PART , TOOLS,MATERIAL YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE INSTALLATION: Carton or other heavy material for covering the counter top. Stud Finder or Thin Nail Clear Tape (for taping the templates to the wall) Keyhole Saw (for the power cord hole) Saber Saw (for cutting vent holes for roof or wail vending)
- Page 7 STEP I: PREPARE THE ELECTRICAL CONNECTION5 ,_k WARNING ,_k AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED! 1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 4 Detail. Cabinet NOTE: The outlet should be on a circuit dedicated to the Upper microwave oven 120V, 60Hz., AC only, with a 20ampere fused electrical supply.
- Page 8 ETEP 2: PREPARE THE VENTING EYEYTEM NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork fittings and length are shown in Figure 9, page WARNING- FiRE HAZARD THIS OVEN MUST BE PROPERLY VENTED! You may vent your oven in one of three ways: Roof Venting If your oven is located...
- Page 9 $TEP 2: PREPARE THE VENTING $YEYTEM STANDARD FiTTiNGS NOTE: If the existing duct is round, must use a rectangular-to-round adapter, with a rectangular 3" extension duct installed between the damper assembly the adapter to prevent the exhaust damper sticking. DUCT LENGTH The total length of the duct...
- Page 10 5TEP 3: PREPARE THE VENTING BLOWER Your microwave oven is shipped with the blower assembled for room venting (recirculafing). You need to adjust the blower if you want waJJ vented or roof vented installation. ,Ek WARN(NG ELECTRICAL SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT.
-
Page 11: Wall Vented Installation
ETEP 3: PREPARE THE VENTING BLOWER WALL VENTED iNSTALLATiON: back plate blower unit 1. Remove blower unit mounting screw(s) and blower plate screw(s). Remove the blower plate from cabinet. blower plate See Figure 12. mounting screw(s) (option) 2. Carefully lift the blower unit out of the microwave oven. -
Page 12: Roof Vented Installation
ETEP 3: PREPARE THE VENTING BLOWER ROOF VENTED iNSTALLATiON: blOwer plate 1. Remove blower unit mounting screw(s) and blower mounting plate screw(s). Remove the blower plate from cabinet. See Figure 18. 2. Carefully lift the blower unit out of the microwave crew(s) (option) oven. - Page 13 STEP 4: PREPARE THE WALL AND UPPER CABINET FOR INSTALLATiON MEASURE AND TACK / TAPE UP THE TEMPLATE 1. Using a plumb line and (metal) measuring tape, find and mark the vertical center line %_ on the back waJJ, as in Figure 22. 2.
- Page 14 STEP 4: PREPARE THE WALl. AND UPPER CABINET FOR INSTALLATION DRILL THE HOLES IN THE WALL AND UPPER CABINET. WARNING BE VERY CAREFUL WHEN DRILLING HOLES INTO THE WALL. Electrical wires could be concealed behind the wall covering if the drill hits them couJd get an electricshock.
-
Page 15: Installl Mounting Plate To Wall
ETEP 5: INSTALl, THE MOUNTING PLATE TO THE WAl,l, THE OVEN MUST BE CONNECTED 3/16" Hole on Studs 5/8" Hole on Drywall Only Minimum 66"1 TO AT LEAST ONE WALL STUD. From theFloor I 1. Draw a vertical line on the wall at the center of the 30"... - Page 16 STEP 5: INSTALL THE MOUNTING PLATE TO THE WALL TO PREPARE THE REAR WALL CUTOUT OPENING AND EXHAUST ADAPTOR/MOUNTING PLATE FOR WALL VENTING ROOF VENTING: * Make the box cutout for the rear wail duct. - 1 piece mounting plate: Using a pencil, put dots through slots F and G, and through...
-
Page 17: Attach Oven To Wall
ETEP 6: A TTACH THE 0 VEN TO THE WALL WARNING You will need two people to lift this power cord microwave. Failure to use more than one person could result in personal injury. power cord hole 1. Carefully lift microwave oven and hang it on support tabs (See Figure 26) at the bottom the mounting... - Page 18 ETEP 6: A TTACH THE 0 VEN TO THE WALL 5. Roof vented installation: See Figure 32. Install ductwork through the vent opening in the upper cabinet. Complete the venting system through the roof according to the method needed. See "PREPARE THE VENTING damper SYSTEM,"...
- Page 19 MEMO...
- Page 20 Printed in Korea...