Electrical Safety; Tool Use And Care - Campbell Hausfeld PW1625 Operating Instructions Manual

Important Safety Information (Continued)
d. Keep clear of nozzle. NEVER direct high pressure spray at a
person, animal, or yourself.
e. NEVER put hand or fingers over the spray tip while operating
the unit.
f. NEVER try to stop or deflect leaks with any body part.
Ensuring that the tool is used
only when the operator and all
other personnel in the work area are wearing ANSI Z87
eye protection equipment, and when required, other
appropriate protection equipment such as head, hearing
protection, gloves, rubber boots, protective clothing when operating
and performing maintenance. Serious eye or permanent hearing loss
could result.
g. High pressure - Gun kicks back – Hold gun with both hands.
h. Keep hose away from sharp objects. Bursting hoses may
cause injury. Examine hose regularly and replace if damaged.
Do not attempt to mend a damaged hose.

eleCtrICAl sAfety

Risk of electrocution:
a. This product is provided with a ground fault circuit
interrupter, GFCI, built into the power cord plug. Be
sure to inspect cord and GFCI prior to use. Any repair or
replacement of the power cord must be performed by a
qualified (licensed or certified) electrical technician. If
replacement of the plug or cord is needed, use only identical
replacement parts.
b. NEVER use an extension cord with this product.
c. Inspect cord before using - Do not use if cord is damaged.
d. Keep all electrical connections dry and off the ground.
e. Do not touch plug with wet hands.
f. Do not spray electrical apparatus and wiring.

tool use And CAre

Do not use pressure that exceeds the operating
pressure of any of the parts (hoses, fittings, etc.)
in the pressurized system. Ensure all equipment and accessories are
rated to withstand the maximum working pressure of the unit.
a. Maintain the tool with care. A properly maintained tool
reduces the risk of problems and is easier to control.
b. Ensure safety devices are operating properly before each use.
DO NOT remove or modify any part of the gun or unit.
c. NEVER operate the machine without all components
properly connected to the machine (handle, gun/wand
assembly, nozzle, etc.).
d. Point gun in safe direction. Unit will start spraying when
trigger is squeezed if "On/Off" switch is in "ON" position.
e. Know how to stop this product and bleed pressure quickly.
Be thoroughly familiar with the controls.
Models PW1625, PW1825, and PW1835
f. ALWAYS engage the trigger safety latch in the safe position
when spraying is stopped even if only for a few moments.
g. NEVER permanently engage the trigger mechanism on the
gun.
h. ALWAYS follow detergent manufacturer's label
recommendations for proper use of detergents. Always
protect eyes, skin, and respiratory system from detergent
use.
i. NEVER disconnect the high pressure discharge hose from
the machine while the system is pressurized. To depressurize
machine, turn power and water supply off, then press the
gun trigger 2-3 times.
j. Unplug unit when not in use.
k. Follow the maintenance instructions specified in the
manual.
Equipment damage:
l. ALWAYS turn water supply "ON" before turning pressure
washer "ON." Running pump dry causes serious damage.
m. Do not operate the pressure washer with the inlet water
screen removed. Keep screen clear of debris and sediment.
n. NEVER operate pressure washer with broken or missing
parts. Check equipment regularly and repair or replace worn
or damaged parts immediately.
o. Use only the lances supplied with this machine.
p. NEVER leave the wand unattended while the machine is
running.
q. ALWAYS hold gun and wand firmly when starting and
operating the machine.
r. Release the trigger when changing from high to low pressure
modes. Failure to do so could result in damage to the nozzle.
s. NEVER store the pressure washer outdoors or where it could
freeze. Freezing temperatures can seriously damage the
pump.
t. Pressure washer is not meant to pump hot water. Do not
connect to hot water supply.
www.chpower.com 5