Binding The Transmitter And Receiver; Main Screen - Spektrum DX4C Instruction Manual

EN

BINDING THE TRANSMITTER AND RECEIVER

In order to operate, the receiver must be bound to the
transmitter. Binding is the process of programming the receiver
to recognize the GUID (Globally Unique Identifi er) code of a single
specifi c transmitter. When a receiver is bound to a transmitter/
model memory, the receiver will only respond to that specifi c
transmitter/model memory.
Binding and Calibrating the Receiver
(AVC Receivers Only)
You must calibrate the receiver each time it is placed in bind
mode.
IMPORTANT: The following sequence of steps must be
followed in order for AVC to function properly.
1. Insert the Bind Plug in the BIND port on the receiver.
2. Power on the receiver. The orange LED fl ashes, indicating
the receiver is in bind mode.
3. Center the ST TRIM and TH TRIM on the transmitter.
4. Put your transmitter in bind mode.
5. The bind process is complete when the orange LED on the
receiver is solid.
6. Pull the transmitter trigger to Full Throttle.
7. Push the transmitter trigger to Full Brake, then return the
trigger to center.
8. Turn the transmitter steering wheel to Full Right.
9. Turn the transmitter steering wheel to Full Left, then return
the steering wheel to center. The orange LED fl ashes once.
10. Remove the bind plug once the calibration and binding
process is complete.
11. Power off the transmitter.
IMPORTANT: You must rebind the transmitter and receiver
if you:
Change the servo reverse after binding
•
Change the travel after binding
•
Want to use the receiver with a different model memory
•

MAIN SCREEN

The Main Screen displays information about the selected model such as trim positions, timer, the model selected, battery voltage,
etc. This screen shows the Timer only when activated.
An alarm will sound when the transmitter's battery voltage goes below the value set in the System Screen.
An alarm will sound when the timer gets to the limit (DOWN) set in the Timer Screen.
While in any screen, press and hold the Rolling Selector for more than 3 seconds to return to the Main Screen.
Throttle (TH) and Steering (ST) trim positions show as blocks in rectangles.
A Active Model Memory
B Model Name
C Transmitter battery voltage
D St (Steering) Trim Position
E Th (Throttle) Trim Position
F Timer
If you change the servo reversing or travel adjust after binding,
AVC will not work properly.
Disabling the Stability Assist Function
If you participate in organized racing, you may be required to turn
AVC technology off. To turn off AVC technology, insert a second
Bind Plug in the Disable port before binding.
IMPORTANT: You must calibrate the receiver each time it is
placed in bind mode. To activate AVC, see the steps in BINDING
AND CALIBRATING THE RECEIVER.
Binding (All other receivers)
1. With the receiver off, insert the bind plug into the BIND port
in the receiver.
2. Power the receiver through any port. If an ESC is being used,
power on the ESC with the ESC lead plugged in the throttle
channel port. The orange LED will fl ash continuously, indica-
ting that the receiver is in bind mode.
3. With the throttle channel in the desired preset failsafe
position (generally full brake and neutral steering), initiate the
bind process with your Spektrum transmitter. This stores the
failsafe position. Continue to hold the failsafe position until
the binding process is complete.
4. The LED on the receiver should now be solid, indicating a
successful bind has taken place.
5. When the bind process is complete, remove the bind plug
from the receiver and store it in a convenient place. Failure
to remove the bind plug will result in the receiver going back
into bind mode.
The only time it is necessary to rebind is if different failsafe
positions are desired e.g., servo travel has been reversed after
the initial bind, or if you want to use the receiver with a different
model memory.
A
B
C
D
SPEKTRUM DX4C • TRANSMITTER INSTRUCTION MANUAL
E
F