Table of Contents
Advertisement
Using Reverse: While driving,
push the throttle trigger
forward to apply brakes.
Once stopped, return the
throttle trigger to neutral.
Push the throttle trigger
forward again to engage
proportional reverse.
6,7
14 • SLASH 4X4 ULTIMATE
TQ 2.4GHz RADIO AND VELINEON POWER SYSTEM
USING THE TQ 2.4GHz RADIO SYSTEM
The TQ 2.4GHz Radio System has been pre-adjusted at the factory. The
adjustment should be checked before running the model, in case of
movement during shipping. Here's how:
1. Turn the transmitter switch on. The status LED on the transmitter
should be solid green (not flashing).
2. Elevate the model on a block or a stand so that all the tires are
off the ground. Make sure your hands are clear of the moving
parts of the model.
3. Plug the battery pack in the model into the speed control.
4. The on/off switch is integrated into the speed control. With the
transmitter on, press and release the EZ-Set button (.25 seconds).
The LED will shine RED (see note, below). This turns the model
on. To turn the VXL-3s off, press and hold the EZ-Set button
until the LED turns off (.5 seconds). Note: If the LED shines
green, Low-Voltage Detection is activated. This will cause erratic
performance from the included NiMH battery pack. The default
factory setting is for Low-Voltage Detection to be disabled
(LED shines red). Make sure to turn the low voltage detection
on when using LiPo batteries. Never use LiPo batteries while
Low-Voltage Detection is turned off. See page 16 for more
information.
5. Turn the steering wheel on the transmitter back and forth and
check for rapid operation of the steering servo. Also, check that
the steering mechanism is
not loose or binding. If the
steering operates slowly,
check for weak batteries.
6. When looking down at
model, the front wheels
should be pointing straight ahead. If the wheels are turned
slightly to the left or right, slowly adjust the steering trim control
on the transmitter until they are pointing straight ahead.
7. Gently operate the throttle trigger to ensure that you have
forward and reverse operation, and that the motor stops when
the throttle trigger is at neutral. Warning: Do not apply full
throttle in forward or reverse while the model is elevated.
8. Once adjustments are made, turn off the receiver on your model,
followed by the hand-held transmitter.
Range-Testing the Radio System
Before each running session with your model, you should range-test
your radio system to ensure that it operates properly.
1. Turn on the radio system and check its operation as described in
the previous section.
2. Have a friend hold the model. Make sure hands and clothing are
clear of the wheels and other moving parts on the model.
3. Make sure your transmitter antenna is fully extended, and then
walk away from the model with the transmitter until you reach
the farthest distance you plan to operate the model.
4. Operate the controls on the transmitter once again to be sure
that the model responds correctly.
5. Do not attempt to operate the model if there is any problem
with the radio system or any external interference with your
radio signal at your location.
• Higher Speeds Require Greater Distance
The faster you drive your Slash 4X4 Ultimate, the more quickly
it will near the limit of radio range. At 60mph, a model can
cover 88 feet every second! It's a thrill, but use caution to keep
your model in range. If you want to see your Slash 4X4 Ultimate
achieve its maximum speed, it is best to position yourself in
the middle of the truck's running area, not the far end, so you
drive the truck towards and past your position. In addition to
maximizing the radio's range, this technique will keep your
model closer to you, making it easier to see and control.
No matter how fast or far you drive your Slash 4X4 Ultimate,
always leave adequate space between you, the model, and others.
Never drive directly toward yourself or others.
TQ 2.4GHz Binding Instructions
For proper operation, the transmitter and receiver must be
electronically 'bound.' This has been done for you at the factory.
Should you ever need to re-bind the system or bind to an additional
transmitter or receiver, follow these instructions. Note: the receiver
must be connected to a 4.8-6.0v (nominal) power source for binding
and the transmitter and receiver must be within 5 feet of each other.
1. Press and hold the transmitter's SET button as you switch
transmitter on. The transmitter's LED will flash red slowly.
Advertisement
Table of Contents
