Advertisement
OPERATION OF CONTROLS
1. POWER ON/OFF button
Press the button (1) to turn on the unit. When the power on,
"Welcome" is scrolled on LCD, then the Radio or Tape mode
is displayed on the LCD 5 seconds, after then the LCD
displays current time. Also press the button (1) to turn off the
unit, "Goodbye" is scrolled on LCD. Although the power off,
the unit can display current time still .
Note: The time form is AM 12 hours and PM 12 hours.
2. SELECT button
1) Audio control ( VOL / BASS / TRE / BAL / FAD )
Press this button (2) less than 1.5 seconds to select the
following features;
"VOL" display - volume control > press knob (2)>
"BAS" display - bass tone control >press knob (2)>
"TRE" display - treble tone control > press knob (2)>
"BAL" display - balance control > press knob (2)>
"FAD" display - fader control > press knob (2)>
and you go back into volume control. If the knob or one of the
keys is not pressed within 5 seconds, the radio automatically
switches into volume level control mode. These settings are
indicated on the LCD window.
VOLUME
BASS
TREBLE
Select
Select
Select
FADER
Select
BALANCE
Select
- 2 -
2) Beep 2nd and I-Vol Selection
When the SEL button is pressed over 2 seconds, the unit will
be operated as below:
Beep 2nd
I-Vol
Press
a. Beep 2nd
On the Beep 2nd, you can control the Beep on or Beep 2nd
by turning the spindle knob.
- Beep on : You can hear "Beep" sound when you press all
buttons.
- Beep 2nd :You can hear "Beep" sound when you press the
button over 1.5 seconds.
b. I-Vol
By pressing the button more than 1.5 seconds again, the unit
will be into the I- VOL mode. (Initial Volume Level Adjustment).
You can adjust the I-Vol of what you want to set by turning the
spindle knob and the I-Vol will be set automatically. After the
setting of initial levels, when the unit is power on/off and ACC
on/off, if the present level is lower or higher than initial level, it
will keep the preset level.
GENERAL OPERATION
1. Press [PWR] button to turn power on.
2. Insert a cassette tape through cassette door. Playing begins
automatically & display will indicate that tape is in motion and
travel direction "
" or "
".
3. Adjust VOL / BAS / TRE / BAL and FAD as desired.
4. Press "
" Eject button at any time to eject cassette.
Note: If end of tape is reached during PLAY or FAST-WIND,
deck will auto-reverse and proceed to play the other side of
cassette tape program. Press Eject button to release cassette.
* The build-up of iron oxide particles which is often even more
server with inferior tapes, will reduce the performance of tape
player. If a loss of clarity / brilliance (high frequency response)
is noticed, the head probably needs cleaning. This may be
done by cleaning the head with a cotton swab moistened in
alcohol or special cleaning fluid.
Head
Alcohol
Cotton Swab
SPECIFICATIONS
FM TUNER
Tuning Range
87.5 - 107.9 MHz
Sensitivity
10dB / uV
Separation
30dB
AM TUNER
Tuning Range
530 - 1710 KHz
Sensitivity
35dB / uV
TAPE DECK
Freq. Response
100 Hz - 8 KHz
Tape Speed
4.75cm / Sec.
Signal - Noise Radio
35dB / uV
Wow & Flutter
0.25%
AUDIO AMP
Power Output
4 x 25 watts
GENERAL
DC 13.8V Negative Ground
Power Supply
Speaker Impedance
4 ohm
- 7 -
Advertisement
