Table of Contents
Advertisement
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MP-2105
Retain This
Manual for
Reference
10-26-06
OWNER'S
MANUAL
MARCY PLATINUM
MP-2105 HOME GYM
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
®
IMPEX
INC.
Advertisement
Table of Contents
Related Manuals for Impex Marcy Platinum MP-2105
Summary of Contents for Impex Marcy Platinum MP-2105
- Page 1 Parts List Warranty Ordering Parts Model MP-2105 Retain This Manual for Reference 10-26-06 OWNER'S MANUAL MARCY PLATINUM MP-2105 HOME GYM IMPEX 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.com ® INC.
-
Page 2: Table Of Contents
WEIGHT RESISTANCE CHART... PARTS LIST………………………………………………………………………….. WARRANTY...… ORDERING PARTS... BEFORE YOU BEGIN Thank you for selecting the MARCY PLATINUM MP2105 HOME GYM by ® IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. complete customer satisfaction. If you have any questions, or find there are missing or damaged parts, we guarantee you complete satisfaction through direct assistance from our factory. -
Page 3: Important Safety Notices
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. -
Page 4: Warning Label Replacement
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. -
Page 5: Hardware Pack
HARDWARE PACK... - Page 6 HARDWARE PACK...
- Page 7 HARDWARE PACK...
-
Page 8: Assembly Instructions
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Insert two Guide Rods (#16) into the holes on the Rear Stabilizer (#15). Secure each Guide Rod with one M10 x ¾”... -
Page 9: Diagram 1
DIAGRAM 1... - Page 10 STEP 2 (See Diagram 2) A.) Attach the Upper Frame (#1) onto the two Guide Rods (#16). Secure it with two M10 x ¾” Allen Bolts (#78) and B.) Place the Upper Frame (#1) onto the Vertical Frame (#4). Secure it with two M10 x 2 ¾” Carriage Bolts (#90), one 4 ¾”...
- Page 11 STEP 3 (See Diagram 3) A.) Attach the Front Press Base (#2) to the Upper Frame (#1). Secure it with one 6 ¾” Front Press Base Axle (#29), two Ø 1 ¼” Washers (#59), and two M10 Aircraft Nuts (#91). B.) Attach the Front Press (#3) to the Front Press Base (#2).
- Page 12 DIAGRAM 3...
- Page 13 STEP 4 (See Diagram 4) A.) Attach the Seat (#32) to the Seat Post (#6). Secure it with two M8 x 1 5/8” Allen Bolts (#86) and Ø 5/8” Washers (#88). B.) Insert the Seat Post into the opening on the Seat Support Frame (#7). Thread the Lock Knob (#40) into the hole on the Seat Support Frame to lock the Seat at selected height.
- Page 14 STEP 5 (See Diagram 5) A.) Slide the Right Butterfly (#10) onto the right axle on the Butterfly Base (#13). B.) Insert the Butterfly Handle (#9) into the pivot on the Right Butterfly. Secure it with one M10 x ¾” Allen Bolt (#78) and C.) Repeat Procedures A and B above to install the other side.
- Page 15 CABLE LOOP DIAGRAM...
- Page 16 STEP 6 (See Diagram 6 & Upper Cable Loop Diagram) A.) Attach the 163” Upper Cable (#33) to the opening on the front of Upper Frame (#1). Make sure the ball stopper is underneath the Frame. Attach a Pulley (#47) to the Cable. B.) Secure the Pulley to the opening with one M10 x 3 ½”...
- Page 17 DIAGRAM 6...
- Page 18 Upper Cable Loop Diagram...
- Page 19 STEP 7 (See Diagram 7 & Lower Cable Loop Diagram) A.) Attach the 164” Lower Cable (#35) to the opening on the Leg Developer (#8). Attach a Pulley (#47) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#84), two 7/8”...
- Page 20 DIAGRAM 7...
- Page 21 Lower Cable Loop Diagram...
- Page 22 STEP 8 (See Diagram 8 & Butterfly Cable Loop Diagram) A.) Clip one end of the 98” Butterfly Cable (#34) to the open slot on the Right Butterfly (#10). B.) Draw the Cable to the open bracket on the right side of the Vertical Frame (#4). Attach a Small Pulley (#73) to the bracket C.) Secure it with one M10 x 1 ¾”...
- Page 24 Butterfly Cable Loop Diagram...
- Page 25 STEP 9 (See Diagram 9) A.) Connect the Lat Bar (#24) to the Upper Cable (#33) with two Hooks (#37) and one Chain (#36). B.) Connect the Abdominal Strap (#70) to the Lower Cable (#35) with a Hook. C.) Connect the Shiver Bar (#19) to the Lower Cable with two Hooks and a Chain. DIAGRAM 9...
-
Page 26: Weight Resistance Chart
WEIGHT RESISTANCE CHART Station Low Pulley Lat Pull Butterfly Front Press AB Crunch Leg Developer Station Low Pulley Lat Pull Butterfly Front Press AB Crunch Leg Developer *Numbers are approximate. Actual weight may vary. *Numbers are approximate. Actual weight may vary. *Numbers are approximate. -
Page 27: Parts List
PARTS LIST KEY NO. DESCRIPTION Upper Frame Front Press Base Front Press Vertical Frame Backrest Support Frame Seat Post Seat Support Frame Leg Developer Butterfly Handle 10 Right Butterfly 11 Left Butterfly 12 Front Base Frame 13 Butterfly Base 14 Rear Base Frame 15 Rear Stabilizer 16 Guide Rod 17 Foot Plate... -
Page 28: Warranty
IMPEX. IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or whatsoever natures.