Summary of Contents for Impex MARCY PLATINUM MP-3105
Page 1
Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model MP-3105 Retain This Manual for Reference 12-27-06 OWNER'S MANUAL MARCY PLATINUM SMITH CAGE MP-3105 IMPEX 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com...
EXPLODED DIAGRAM…………………………………………………………….. PARTS LIST………..……………………………………………………………….. WARRANTY...…. 26 ORDERING PARTS...… 26 BEFORE YOU BEGIN Thank you for selecting the MARCY PLATINUM Smith Cage MP-3105 by ® IMPEX . For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
Page 4
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Cross Brace, Rear Stabilizer, and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in location shown.
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) NOTE: Do not tighten the Nuts and Bolts until instructed to do so. B.) Attach one Diagonal Support (#3) to the Right Cross Brace (#15).
Page 11
STEP 2 (See Diagram 2) A.) Attach the Left Vertical Beam (#1) to the left Diagonal Support (#3). Secure it with two M10 x 2 ¾” Carriage Bolts (#83), one 4 3/8” x 2 ¾” Bent Bracket (#25), two Ø ¾” Washers (#87), and two M10 Aircraft Nuts (#89).
Page 12
STEP 3 (See Diagram 3) A.) Place the Weight Glide Post (#12) onto the Weight Glide Post Base (#11). Secure it with four M10 x ¾” Carriage Bolts (#79), Ø ¾” Washers (#87) and M10 Aircraft Nuts (#89). B.) Slide the Sliding Weight Post (#22) onto the Weight Glide Post. C.) Attach the Upper Frame (#13) onto the Rear Vertical Beam (#10).
Page 14
STEP 4 (See Diagram 4) A.) Attach the Butterfly Base (#17) to the front of Rear Vertical Beam (#10). Attach the Butterfly Pulley Bracket (#18) to the back of Rear Vertical Beam. Align the holes and secure them with two M10 x 2” Carriage Bolts (#80), Ø ¾” Washers (#87), and M10 Aircraft Nuts (#89). B.) Insert the Axle on the Left Butterfly (#19) into the Butterfly Base from the bottom.
Page 16
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach a 123” Cable (#37) to the front opening on the Upper Frame (#13). Attach a Pulley (#44) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#75), two Ø 1 1/8”...
Page 18
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 79” Butterfly Cable (#36) to the clip on the Left Butterfly (#19). Draw the Cable to the left Butterfly Pulley Bracket (#18). B.) Attach a Pulley (#44) to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#73), two Washers (#87), and one M10 Aircraft Nut (#89).
Page 19
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach one 123” Cable (#37) to the lower opening on the Rear Vertical Beam (#10). Attach a Small Pulley (#45) to the opening. Secure it with a M10 x 2 ¾” Allen Bolt (#76), two Ø 1” x 5/8”...
Page 20
STEP 8 (See Diagram 8) A.) Note: Help of another person is strongly recommended for this step. Place the Weight Lifting Sleeve (#6) in between the two Safety Stop Frames (#7 & #8). Align the holes and insert the Weight Bar (#9) into the Left Safety Stop Frame through the Weight Lifting Sleeve to the other end of Right Safety Stop Frame.
Page 21
STEP 9 (See Diagram 9) A.) Attach the Main Seat Support (#92) to the Rear Stabilizer (#93). Secure it with two M10 x 3 ½” Allen Bolts (#114), one 2 ¾” x 2” Bent Bracket (#27) and two Ø ¾” Washers (#87).
Page 22
STEP-10 (See Diagram 10) A.) Attach the Seat Bracket (#95) to the pivot on the Main Seat Support (#92). B.) Attach the two Backrest Supports (#97) to the Seat Bracket (#95) and align the holes. Secure them with a M12 x 8 ½” Allen Bolt (#113), two Ø 1” Washers (#111), and one M12 Aircraft Nut (#112).
Page 23
STEP-11 (See Diagram 11) A.) Place the Seat Pad (#103) onto the Seat Bracket (#95). Secure it with four M8 x 1 5/8” Allen Bolts (#98) and Ø 5/8” Washers (#86). B.) Attach the Bench Backrest Board (#104) to the Backrest Supports (#97). Secure it with four M8 x 1 5/8”...
PARTS LIST KEY NO. DESCRIPTION Left Vertical Beam Right Vertical Beam Diagonal Support Guide Rod Bracket Guide Rod Lifting Sleeve Left Safety Stop Frame Right Safety Stop Frame Weight Bar 10 Rear Vertical Beam 11 Weight Glide Post Base 12 Weight Glide Post 13 Upper Frame 14 Left Cross Brace 15 Right Cross Brace...
Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option.