TG8051_8061PD(e-hg).book Page 19 Wednesday, February 2, 2011 2:33 PM
Fontos:
L If a handset is not placed on the base unit when
a power failure occurs, "Nincs áram Nyomja:
ic" is displayed. After pressing {ic} on the
handset, place it on the base unit to start power
back-up mode.
L Power back-up mode will not work if the battery
level of the power supplying handset is )/0)4.
L Do not lift the power supplying handset from the
base unit during power back-up mode.
L Do not touch the handset's charge contacts
during power back-up mode.
L If the battery level is low, the unit will not work
sufficiently during power back-up mode. In
addition, in case handset battery power runs out,
we recommend connecting a corded-type
telephone (without AC adaptor) to the same
telephone line or to the same telephone line jack,
if you have such a telephone jack in your house.
L Calls cannot be made during a power failure until
key lock is turned off (18. oldal).
Panasonic Ni-MH battery performance
(supplied batteries) during power back-up
mode
When the batteries are fully charged, operating time
of the handset in power back-up mode varies
depending on usage.
– Continuous use of the handset in power back-up
mode: 2 hours max.
– Continuous use of the handset other than
a handset in power back-up mode: 3 hours max.
– Not in use in power back-up mode: 3 hours max.
Megjegyzés:
L Actual battery performance depends on usage
and ambient environment.
Making calls during a power failure
■ When only 1 handset is registered:
1
Lift the handset and dial the phone
number.
2
Within 1 minute, place the handset on the
base unit.
L Wait until speakerphone is turned on
automatically and the call is made.
3
When the other party answers the call,
keep the handset on the base unit and talk
using the speakerphone.
4
When you finish talking, press {ic}.
Making/Answering Calls
Megjegyzés:
L In step 2, if you do not place the handset on the
base unit within 1 minute, the power back-up
mode turns off. In this case, press {ic} on the
handset and dial the phone number. Then try
again from step 2.
■ When 2 or more handsets are registered:
You should leave one handset on the base unit
for supplying the power, and use another
handset for making calls. For the operation,
please see „Making calls", 17. oldal.
Megjegyzés:
L During a call with the handset placed on the
base unit (power back-up mode), the call may be
disconnected if you touch the handset. In such
case, try to call back.
L The range of the base unit is limited during
a power failure. Please use the handset close to
the base unit.
Making a call using the redial list
■ When only 1 handset is registered:
1
Lift the handset.
2
j (right soft key) or {>} (R)
3
{r}: Select the desired phone number.
4
Within 1 minute, place the handset on the
base unit.
L Wait until speakerphone is turned on
automatically and the call is made.
■ When 2 or more handsets are registered:
You should leave one handset on the base unit
for supplying the power, and use another
handset for making calls. For the operation,
please see „Making a call using the redial list",
17. oldal.
Making a call using the handset
phonebook
■ When only 1 handset is registered:
1
Lift the handset.
2
n (left soft key)
3
{r}: Select the desired entry.
4
Within 1 minute, place the handset on the
base unit.
L Wait until speakerphone is turned on
automatically and the call is made.
■ When 2 or more handsets are registered:
You should leave one handset on the base unit
for supplying the power, and use another
handset for making calls. For the operation,
19