Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for DeWalt D26411-XE
Summary of Contents for DeWalt D26411-XE
- Page 1 INSTRUCTION MANUAL D26411-XE, D26414-XE HEAT GUN...
-
Page 3: Definitions: Safety Guidelines
Before beginning any paint removal process you should determine whether the paint Definitions: Safety Guidelines your are removing contains lead. This can be done by your local health department or by a professional who uses a paint analyzer to check the lead content of the The definitions below describe the level of severity for each paint to be removed. -
Page 4: Personal Safety
e) When operating a power tool outdoors, use an extension cord suitable or storing power tools. Such preventive safety measures reduce the risk of for outdoor use. Use of a cord suitable for outdoor use reduces the risk of starting the power tool accidentally. electric shock. -
Page 5: Extension Cords
Extension Cords • Avoid poking anything down inside the nozzle. • Know your work environment. Remember that areas behind soffit board, ceilings, CAUTION: Use only extension cords that are approved by the country’s Electrical and floors may contain highly flammable materials. Check these areas before Authority. - Page 6 As you become more familiar with the tool and develop the proper technique, the danger • Wear a dust respirator mask or a dual filter (dust and fume) respirator mask of accidental ignition will be greatly reduced. In establishing the proper technique, the which has been approved by the Occupational Safety and Health Administration best thing to do is PRACTICE! Work on simple stripping projects, preferably outdoors, (OSHA), the National Institute of Safety and Health (NIOSH), or the United States...
-
Page 7: Specifications
• The label on your tool may include the following symbols. The symbols and their definitions are as follows: Your D WALT heat gun D26411-XE/D26414-XE has been designed for stripping paint, soldering pipes, shrinking PVC, welding and bending plastics as well as general drying V ....volts A ....amperes... -
Page 8: Assembly And Adjustments
Setting Applications D26414-XE FIG.1 • Drying paint and varnish • Removing stickers • Waxing and dewaxing • Drying wet timber prior to filling • Shrinking PVC wrapping and insulation tubes • Thawing frozen pipes Medium • Welding plastics • Bending plastic pipes and sheets •... -
Page 9: Prior To Operation
Switching On and Off (Fig. 4) Icon Description Purpose φ 1. Push the on/off switch (A) to the desired air flow settings: Cone nozzle Welding, shrink sleeving (heat concentrated over 1.24 liter/min [50˚ C-400˚ C 122–752º F)] small area) A low air flow to heat up the workpiece slowly. 50 mm Fish tail Drying, thawing surface nozzle... -
Page 10: Maintenance
4. Direct the hot air onto the paint to be removed. NOTE: To reduce the cooling time, switch the tool on at the lowest air temperature setting and let it run for a few minutes before turning the heat gun off. Best results will be achieved if the heat gun is moved slowly, but CONSTANTLY, from side to side to evenly distribute heat. -
Page 11: Three Year Limited Warranty
Guarantee FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call (AUS) 1800 654 155 or (NZ) 0800 339258 for a free replacement. Applicable to hand held Power Tools, Lasers and Nailers. Three Year Limited Warranty WALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase. - Page 12 WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 • 20 Fletcher Road, Mooroolbark, VIC 3138 Australia (MAR09) Part No. N028947 D26411-XE, D26414-XE Copyright © 2009 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip;...