SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, Safety is secured against an X-ray by consider- they are indicated with the labels or seals on the ing about the cathode-ray tube and the high cabinet, chassis and parts.
CONTENTS SERVICING NOTICES ON CHECKING ....................A1-1 HOW TO ORDER PARTS ........................A1-1 IMPORTANT ............................A1-1 CONTENTS .............................. A2-1 GENERAL SPECIFICATIONS ........................A3-1~A3-4 DISASSEMBLY INSTRUCTIONS ......................SERVICE MODE LIST ..........................CONFIRMATION OF USING HOURS ...................... NOTE FOR THE REPLACING OF MEMORY IC ..................ELECTRICAL ADJUSTMENTS ........................
G E N E R A L S P E C I F I C A T I O N S G-1.Outline of the Product 13 inch(335.4mmV):Measured diagonally Color CRT 90 degree deflection G-2.Broadcasting System System G-3.Color System NTSC SECAM or Monochrome signal G-4.NTSC Playback(PAL 60Hz) G-5.NTSC 3.58+4.43/PAL60Hz G-6.Antenna Input Impedance...
Page 5
G E N E R A L S P E C I F I C A T I O N S G-18.Regulation S afety NEMKO FEMKO DEMKO IEC65 SEMKO HOMOLO SABS SISIR AS3159 DENTORI GOST NONE Radiation SABA HOMOLO CISPR13 DENTORI AS/NZS NONE...
Page 6
G E N E R A L S P E C I F I C A T I O N S G-27.Speaker inches Imp. ohm x W (Typical) W (Typical) G-28.EXT Speaker G-29.Carton Master Carton: Need No Need Content: ---- Material: ---- / ----...
Page 7
G E N E R A L S P E C I F I C A T I O N S G-33.Magnetic Field BV : +0.45G BV : +0.35G BV : +0.25G BH : 0.18G BH : 0.30G BH : 0.30G BV : -0.15G...
DISASSEMBLY INSTRUCTIONS 3. After one side is removed, pull in the opposite direction to 1. REMOVAL OF ANODE CAP remove the other. Read the following NOTED items before starting work. NOTE After turning the power off there might still be a potential Take care not to damage the Rubber Cap.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 2 seconds. Set Key Remocon Key Operations Releasing of V-CHIP PASSWORD.
ELECTRICAL ADJUSTMENTS 1. BEFORE MAKING ELECTRICAL 1. RF AGC DELAY ADJUSTMENTS 2. VIDEO LEVEL Read and perform these adjustments when repairing the 3. FM LEVEL circuits or replacing electrical parts or PCB assemblies. 4. OSD H 5. CUT OFF CAUTION 6.
Page 11
ELECTRICAL ADJUSTMENTS 2-5: SUB TINT/SUB COLOR 1. H. PHASE Receive the color bar pattern. 2. H. BLK Connect the synchro scope to TP023. 3. V. SIZE Activate the adjustment mode display of Fig. 2-1 and 4. V. POSI press the channel button (4) on the remote control. 5.
Page 12
ELECTRICAL ADJUSTMENTS [ TV ] OSD H Fig. 2-8 2-12: VCO FREERUN Place the set with Aging Test for more than 10 minutes. Receive the UHF. Disconnect the Antenna while receiving the UHF and set to the Noise screen. Once turn off the Power and turn on the Power again. Approxi.
Page 13
ELECTRICAL ADJUSTMENTS PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator. minutes before performing the following adjustments.
BLOCK DIAGRAM EARPHONE JACK CH. UP V. SIZE/VIDEO/CHROMA/SYNC TU001 IC201 LA76814M-MPB CH. DOWN IC351 AN7511 T351 AUDIO SOUND SOUND TRANS VOL. UP SP351 IF/RF AGC VOL. DOWN DRIVE CF201 Q604, Q605 SAW FILTER VIDEO VIDEO MICON VIDEO POWER BUFFER IC101 OEC3039B Q801 MUTE P00 RED R...
Page 19
CHROMA SCHEMATIC DIAGRAM VIDEO VIDEO BUFFER BUFFER Q604 Q605 2SA1015Y 2SA1015Y D609 R652 1SS133 L205 R624 3602038 R660 R662 C628 0.047 M TP201 C610 100P SL C218 3.3 2.2 0.001 Y C217 R208 0.47 CLMP CLMP X-RAY VIDEO R203 TRAP HOR GND VIDEO VIDEO...
Page 20
DEFLECTION/CRT SCHEMATIC DIAGRAM FROM/TO CHROMA CLAMP CLAMP CLAMP CLAMP CLAMP G.OUT G.OUT G.OUT G.OUT G.OUT B.OUT B.OUT B.OUT B.OUT B.OUT R.OUT R.OUT R.OUT R.OUT R.OUT CD802 CP802A CP802B 2E052503 51048-0510 51048-0510 V-OUT IC401 LA7840 THERMAL PUMP PROTECTION AMP - RED OUT GREEN OUT BLUE OUT Q801...
Page 21
POWER/SOUND AMP SCHEMATIC DIAGRAM CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE 4A 125V (F501) FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES 4A 125V D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME TYPE 4A 125V (F501). DEGAUSE COIL L502 8F140025...
WAVEFORMS MICON/TUNER 200mV. 5ms/div 0.5V. 20µs/div 1V. 0.5ms/div 20V. 20µs/div 0.5V. 20µs/div 0.5V. 20µs/div 0.5V. 20µs/div 200mV. 20µs/div 200mV. 20µs/div 200mV. 5ms/div 200mV. 20µs/div 14 0.5V. 5ms/div CHROMA 1V. 20µs/div 0.5V. 20µs/div 0.5V. 2ms/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
WAVEFORMS 50V. 20µs/div 16 1V. 20µs/div 200V. 20µs/div POWER/SOUND AMP 1V. 20µs/div 50mV. 0.5ms/div 10V. 5ms/div DEFLECTION/CRT 200mV. 0.5ms/div 18 0.5V. 5ms/div 5V. 5ms/div 20V. 20µs/div 50V. 20µs/div 2V. 20µs/div 50V. 20µs/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.