SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, Safety is secured against an X-ray by consider- they are indicated with the labels or seals on the ing about the cathode-ray tube and the high cabinet, chassis and parts.
CONTENTS SERVICING NOTICES ON CHECKING ...................... A1-1 HOW TO ORDER PARTS ........................... A1-1 IMPORTANT ..............................A1-1 CONTENTS ..............................A2-1 GENERAL SPECIFICATIONS ........................A3-1~A3-4 DISASSEMBLY INSTRUCTIONS ....................... SERVICE MODE LIST ..........................CONFIRMATION OF USING HOURS ......................NOTE FOR THE REPLACING OF MEMORY IC ..................ELECTRICAL ADJUSTMENTS ........................
GENERAL SPECIFICATIONS G-1.Outline of the Product 19 inch(480.0mmV):Measured diagonally Color CRT 90 degree deflection G-2.Broadcasting System System G-3.Color System NTSC SECAM or Monochrome signal G-4.NTSC Playback(PAL 60Hz) G-5.NTSC 3.58+4.43/PAL60Hz G-6.Antenna Input Impedance VHF/UHF 75 ohm unbalanced G-7.Tuner and Receiving Channel Tuner : Contactless Electric Tuner Oscar(W/O HYPER) Oscar(W/ HYPER)
Page 5
GENERAL SPECIFICATIONS G-19.Temperature Operation ˚C ~ 40 ˚C Storage ˚C ~ 60 ˚C G-20.Operating Humidity Less than G-21.Clock and Timer Sleep Timer Yes Max 120 Min.( 10 Min. Step) On/Off Timer Programs Wake Up Timer Programs G-22.Timer back up Time: More than -- Minutes (at Power Off Mode) G-23.Terminals...
Page 6
GENERAL SPECIFICATIONS G-29.Carton Master Carton: Need No Need Content: ---- Material: ---- / ---- Corrugated Carton Dimensions: ---- mm(L) ---- mm(W) ---- mm(D) Description of Origin Gift Box Material Double/Brown Corrugated Carton ( with Photo Label) Double/White Corrugated Carton ( with Photo Label) Double Full Color Carton W/Photo Dimensions:...
Page 7
GENERAL SPECIFICATIONS G-34.Remote Control Unit: RC-74 Glow in Dark Remocon Power Source: Battery UM - 4 x 2 Total 26 Key Power Quick View TV/AV Stand By Status Bar Select Time Select PAL/SECAM Time Set Volume Up Mute Volume Down CH Skip CH Call CH1/CH2...
DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP 3. After one side is removed, pull in the opposite direction to remove the other. Read the following NOTED items before starting work. NOTE After turning the power off there might still be a potential Take care not to damage the Rubber Cap.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 1 second. Set Key Remocon Key Operations Releasing of V-CHIP PASSWORD.
ELECTRICAL ADJUSTMENTS 1. BEFORE MAKING ELECTRICAL 2. BASIC ADJUSTMENTS ADJUSTMENTS 2-1: RF AGC DELAY Read and perform these adjustments when repairing the Receive an 80dB monoscope pattern. circuits or replacing electrical parts or PCB assemblies. Connect the digital voltmeter between the TP001 and the GND.
Page 11
ELECTRICAL ADJUSTMENTS Fig. 2-1 00 OSD Fig. 2-3 2-10: VERTICAL VCO Place the set with Aging Test for more than 10 minutes. 110% Receive an 80dB monoscope pattern. Connect the digital voltmeter between the pin 5 of CP601 and the GND. 100% Activate the adjustment mode display of Fig.
Page 12
ELECTRICAL ADJUSTMENTS PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator. minutes before performing the following adjustments.
Page 20
POWER SCHEMATIC DIAGRAM (MAIN PCB) CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE 4A 125V (F501) FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME 4A 125V TYPE 4A 125V (F501). R502 CP502 TV-50P-02-A1...
WAVEFORMS 16 2V 20 s/div 21 50V 20 s/div 22 50V 20 s/div 200V 20 s/div POWER 0.5V 1ms/div 10V 5ms/div 10V 5ms/div 1V 1ms/div 50V 20 s/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.