Audio And Video Information - Panasonic DMP-BD80 Operating Instructions Manual

Audio and video information
About audio from audio output terminals
-
-
-
Before connecting, read the table below, and confirm the desired audio type and necessary settings ("BD-Video Secondary Audio", "Dolby D/Dolby
o
+/Dolby TrueHD" or "DTSIDTS-HD"). (Q 9)
eThe number of channels listed is the maximum possible number of output channels.
HDMI AV OUT/DIGITAL AUDIO OUT
(CoaxiaIIBD80VOptical)
7.1ch PCM*'
5.1ch PCM
. .: 7.1ch PCM*'
Down-mixed
2ch PCM
DTS Digital
Surround
DTS Digital
Surround/
DTS-ES*6
Down-mixed
2ch PCM
Dolby Digital 7.1ch PCM
7.1ch PCM
1!mI!I:
5.1ch PCM
Down-mixed
5.1ch PCM*2
5.1ch PCM*2
7.1ch PCM
DTS Digital
Surround/
DTS-ES
Dolby Digital
Plus
DTS-HD High
Resolution
Audio
Dolby TrueHD
DTS-HD Master
Audio
DTS Digital
Surround
DTS Digital
Surround/
DTS-ES*6
Down-mixed
5.1ch PCM
AUDIO OUT
(Analog)
5.1ch*2 7.1ch
":7.1ch*'
1!mI!I:
5.1 ch
2ch 5.1ch
7.1ch
7.1ch*'
Down-mixed
5.1ch*2
eAlso, depending on the specifications or the settings of the amplifier/receiver, the results of the output may vary.
*1 When the connected equipment is not supported with these audio formats, the audio is output as Dolby Digital bitstream, DTS Digital Surround
bitstream or down-mixed 2ch PCM (e.g., TV).
*2 . .: When playing BD-Video without secondary audio or button click sound, the audio is output as the same format as if "BD-Video
Secondary Audio" was set to "Off'.
*3 When the connected equipment is not supported with multi channel surround, the audio is output as down-mixed 2ch PCM.
*4 . .: When the connected equipment is supported with 7.1 channel surround, the audio output is amplified from 5.1 ch or 6.1 ch to 7.1 ch
depending on the DTS, Inc. specifications.
*5 With PCM output, Dolby Digital EX becomes PCM audio decoded as Dolby Digital, DTS-ES recorded to DVD-Video becomes PCM audio
decoded as DTS Digital Surround, and DTS-ES recorded to BD-Video becomes PCM audio decoded as DTS-ES.
*6 . .: When "BD-Video Secondary Audio" is set to "On", Dolby Digital EX is output as Dolby Digital and DTS-ES is output as DTS Digital
Surround, however if playing BD-Video without secondary audio or button click sound, the audio is output as the original format.
Enjoying High Sit rate Audio of SO-Video
1mB
.
- -
-
--~-
-
-
This unit supports high bit rate audio (Dolby Digital Plus, Dolby TrueHD, DTS-HD High Resolution Audio and DTS-HD Master Audio) adopted in BD-Video.
In order to enjoy these audio formats, the following conditions are necessary. (Part shown in the shaded area of table given above)
NECESSARY CONNECTIONS
eHDMI AV OUT terminal: (Q ~
e7.1ch AUDIO OUT
terminal~:
(Q 12)/5.1ch AUDIO OUT terminallBD801: (Q 13)
NECESSARY SETTINGS (Q 9)
eSet "BD-Video Secondary Audio" to "Off'.
eHDMI AV OUT terminal: Set "Dolby D/Dolby 0 +/Dolby TrueHD" or "DTS/DTS-HD" to "Bitstream" or "PCM" .
e7.1ch AUDIO OUT terminaIIBD80I: Set "Analog Audio Output" to "7.1ch".
e5.1ch AUDIO OUT terminal
BD80:
Set "Analog Audio Output" to "2ch (Downmix) + 5.1ch".
o
eThe button click sound on the menu and audio with secondary video in picture-in-picture mode (Q 22) is not output.
RQT9378