Husqvarna 323HD60, 325HD60X-Series, 325HD75X-Series Operator's Manual
Husqvarna electric hedge trimmer operator's manual
Hide thumbs
Also See for 323HD60, 325HD60X-Series, 325HD75X-Series:
- Operator's manual (28 pages) ,
- Operator's manual (24 pages) ,
- Operator's manual (24 pages)
Table of Contents
Related Manuals for Husqvarna 323HD60, 325HD60X-Series, 325HD75X-Series
Summary of Contents for Husqvarna 323HD60, 325HD60X-Series, 325HD75X-Series
- Page 1 323HD60 325HD60 325HD75 Oper ator ′ s manual X-series X-series Please r ead the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
-
Page 2: Key To Symbols
Symbols W ARNING! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual. -
Page 3: Table Of Contents
W ARNING! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual. -
Page 4: Intr Oduction
Dear Customer , Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Charles XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant. -
Page 5: What Is What
What is what? 1 Operator ′ s manual 2 Grease filler cap, bevel gear 3 Gear housing 4 Blades 5 Blade guard 6 Front handle 7 Cylinder cover 8 Starter handle 9 Stop switch 10 Throttle lock 11 Adjustable handle 12 Throttle control WHA T IS WHA T? 13 Lock for handle (325HD60, 325HD75) -
Page 6: General Safety Preca Utions
Personal protective equipment IMPOR TANT! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual. -
Page 7: Machine ' S Safety Equipment
See instructions under the heading Start. Start the hedge trimmer and apply full throttle. Release the throttle trigger and check that the blades stop and remain stationary. If the blades move when the throttle trigger is in the idle position then the carburettor idle setting must be adjusted. - Page 8 GENERAL SAFETY PRECA UTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier. The machine′s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine′s handle unit.
- Page 9 GENERAL SAFETY PRECAUTIONS Blades To ensure good cutting results it is important that the contact pressure between the blades is correct. The contact pressure is adjusted by turning the screws on the underside of the bar clockwise as far as they will go. Then turn the screws anticlockwise a 1/4 turn.
-
Page 10: Fuel Handling
When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For best results and performance use HUSQVARNA two- stroke engine oil, which is specially formulated for our air- cooled two-stroke engines. • Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW). -
Page 11: Fuelling
Mixing • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. •... -
Page 12: Starting And Stopping
STARTING AND STOPPING Check before starting • Inspect the working area. Remove any objects that could be thrown out. • Check the cutting attachment. Never use blades that are dull, cracked or damaged. • Check that the machine is in perfect working order. Check that all nuts and screws are tight. - Page 13 STARTING AND STOPPING Starting Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull the cord.
-
Page 14: Working Techniques
General working instructions IMPORTANT! This section takes up the basic safety precautions for working with a hedge trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. -
Page 15: Basic Working Techniques
(325HD60, 325HD75) • The hedge trimmer’s rear handle can be set in three positions by pulling out the catch. See figure. When the handle is adjusted the hedge trimmer should be idling or not running. -
Page 16: Maintenance
Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions... -
Page 17: Muffler
Fine adjustment of the idle speed T Adjust the idle speed with the idle adjustment screw T, if adjustment is necessary. First turn the idle adjustment screw T clockwise until the blades start to move. Then turn the idle adjustment screw T anticlockwise until the blades stop. The idle speed is correctly adjusted when the engine runs smoothly in every position. -
Page 18: Cooling System
See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. -
Page 19: Gear Housing
There is a grease nipple and a plug for filling lubricant on the gear housing. Use a grease gun to fill with grease. This should be done after every 60 working hours. Use Husqvarna’s special grease, no. 503 98 96-01. -
Page 20: Maintenance Schedule
Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. More extensive work must be carried out by an authorised service workshop. -
Page 21: Technical D Atat Echnical Data
Technical data Technical data Engine Cylinder displacement, cm Cylinder bore, mm Stroke, mm Idle speed, rpm Recommended max. speed, rpm Max. engine output, acc. to ISO 8893 Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, mm Fuel and lubrication system Manufacturer/type of carburettor... -
Page 22: Ec-Declaration Of Conformity (Applies To Europe Only)
Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under sole responsibility that the hedge trimmers Husqvarna 323HD60, 325HD60 and 325HD75 from 2002’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the standards or or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:... - Page 24 1150087-26 ´®z+R(h¶6+¨ ´®z+R(h¶6+¨ 2005-05-31...