Husqvarna 323HD60 Operator's Manual
Hide thumbs
Also See for 323HD60:
- Operator's manual (24 pages) ,
- Operator's manual (24 pages) ,
- Operator's manual (24 pages)
Table of Contents
Related Manuals for Husqvarna 323HD60
Summary of Contents for Husqvarna 323HD60
- Page 1 Operator′s manual 323HD60 325HD60 X-series 325HD75 X-series Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
-
Page 2: Key To Symbols
KEY TO SYMBOLS Symbols Always wear approved protective WARNING! Incorrect or careless gloves. use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read Regular cleaning is required. -
Page 3: Table Of Contents
CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Symbols ..............2 Please read the operator’s manual carefully. CONTENTS Contents ............... 3 WARNING! Long-term exposure to noise can result in permanent hearing Note the following before starting: ......3 impairment. -
Page 4: Introduction
Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets. -
Page 5: What Is What
WHAT IS WHAT? What is what? Operator′s manual 13 Lock for handle (325HD60, 325HD75) Grease filler cap, bevel gear 14 Fuel tank Gear 15 Fuel cap Blades 16 Air purge Blade guard 17 Choke control Front handle 18 Air filter cover Cylinder cover 19 Hand guard Starter handle... -
Page 6: General Safety Precautions
GENERAL SAFETY PRECAUTIONS Important Personal protective equipment IMPORTANT! IMPORTANT! The machine is only designed for cutting branches and Incorrect or careless use of a hedge trimmer can turn it twigs. into a dangerous tool that can cause serious or even fatal injury. -
Page 7: Machine's Safety Equipment
GENERAL SAFETY PRECAUTIONS CLOTHING the throttle control is automatically locked at the idle setting. Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. - Page 8 GENERAL SAFETY PRECAUTIONS Stop switch Regularly check the vibration damping units for cracks or deformation. Check that the vibration damping element is Use the stop switch to switch off the engine. undamaged and securely attached. WARNING! Overexposure to vibration can lead to circulatory damage or nerve damage in people who have impaired circulation.
- Page 9 GENERAL SAFETY PRECAUTIONS Never use a machine that has a faulty muffler. When the blades are correctly adjusted the play between the blades should be 0,2–0,4 mm, measured at the screws. The edges of the blades are too hard to be filed. Dull blades should be sharpened using a grinder.
-
Page 10: Fuel Handling
Two-stroke oil • Secure the machine during transport. • For best results and performance use HUSQVARNA • In order to prevent unintentional starting of the engine, two-stroke engine oil, which is specially formulated for the spark plug cap must always be removed during our air-cooled two-stroke engines. -
Page 11: Fuelling
FUEL HANDLING Mixing Fuelling • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix WARNING! Taking the following (shake) the fuel mixture. -
Page 12: Starting And Stopping
STARTING AND STOPPING Check before starting Cold engine Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled. • Inspect the working area. Remove any objects that could be thrown out. •... - Page 13 STARTING AND STOPPING CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. Stopping The engine is switched off by moving the stop switch to the stop position.
-
Page 14: Working Techniques
WORKING TECHNIQUES General working instructions • Never work from a ladder, stool or any other raised position that is not fully secured. IMPORTANT! This section takes up the basic safety precautions for working with a hedge trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert. -
Page 15: Basic Working Techniques
WORKING TECHNIQUES • When the engine is switched off, keep your hands and • When trimming a hedge the engine should always feet away from the cutting attachment until it has face away from the hedge. stopped completely. • Hold the machine as close to your body as possible to •... -
Page 16: Maintenance
Carburettor the optimal setting and should be maintained for the first few hours the machine is in use. The carburettor Your Husqvarna product has been designed and should then be finely adjusted. Fine adjustment manufactured to specifications that reduce harmful should be carried out by a skilled technician. -
Page 17: Cooling System
MAINTENANCE cause fire if directed against dry and combustible Cooling system material. To keep the working temperature as low as possible the machine is equipped with a cooling system. Some mufflers are equipped with a special spark arrestor mesh. If your machine has this type of muffler, you should clean the mesh at least once a week. -
Page 18: Air Filter
Lubricate the blade bars with special grease, part no. 531 00 75-12 (UL 21) before long periods of storage. Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. -
Page 19: Maintenance Schedule
MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. -
Page 20: Technical Data
TECHNICAL DATA Technical data Technical data 323HD60 325HD60 325HD75 Engine Cylinder displacement, cm 24,5 24,5 24,5 Cylinder bore, mm 34,0 34,0 34,0 Stroke, mm Idle speed, rpm 2700 2700 2700 Recommended max. speed, rpm 10500-12500 10500-12500 10500-12500 Max. engine output, acc. to ISO 8893... -
Page 21: Ec-Declaration Of Conformity
Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under sole responsibility that the hedge trimmers Husqvarna 323HD60, 325HD60 and 325HD75 from 2009’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the standards or or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:... - Page 28 Original instructions 1153242-26 ´®z+U86¶6)¨ ´®z+U86¶6)¨ 2010-03-10...