Fcc Compliance; Software And Firmware Use; Disclaimer - Scientific Atlanta Explorer 4240C User Manual

FCC Compliance

United States FCC Compliance
This device has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
such interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy. If not
installed and used in accordance with the instructions, it may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment OFF and ON, the user is encouraged to try
to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna, if applicable.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the cable company or an experienced radio/
television technician for help.
Any changes or modifi cations not expressly approved by Cisco
Systems, Inc., could void the user's authority to operate the
equipment.
The information shown in the FCC Declaration of Conformity
paragraph below is a requirement of the FCC and is intended to
supply you with information regarding the FCC approval of this
device. The phone numbers listed are for FCC-related questions
only and not intended for questions regarding the connection
or operation for this device. Please contact your cable service
provider for any questions you may have regarding the operation or
installation of this device.
Declaration of Conformity
This device complies with Part 15 of FCC Rules. Operation is
subject to the following two conditions:
1) the device may not cause harmful interference, and 2) the device
must accept any interference received, including interference that
may cause undesired operation.
Cisco Systems, Inc.
5030 Sugarloaf Parkway, Box 465447
Lawrenceville, GA 30042
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affi liates in the U.S. and other countries. A listing of Cisco's trademarks can be found
at www.cisco.com/go/trademarks.
CableCARD and M-Card are trademarks of Cable Television Laboratories, Inc.
Manufactured under license from Dolby Laboratories. Dolby is a trademark of Dolby Laboratories.
Macrovision is a registered trademark of Macrovision Corp.
Other third party trademarks mentioned are the property of their respective owners.
The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)
© 2007, 2010, 2012 Cisco Systems, Inc. All rights reserved.
August 2012
Manufactured by: Cisco Systems, Inc.;
Lawrenceville, Georgia 30044; USA
Canada EMI Regulation
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class B est conforme à la norme
NMB-003 du Canada.

Software and Firmware Use

Cisco Systems, Inc. owns copyrights to the software included
in your set-top and furnishes the software to your cable service
provider under a license agreement. You may only use or copy
this software in accordance with the terms of your cable service
provider.
Cisco Systems, Inc. owns copyrights to the fi rmware in this
equipment. You may only use the fi rmware in the equipment
in which it is provided. Any reproduction or distribution of
this fi rmware, or any portion of it, without the express written
consent of Cisco Systems, Inc. is prohibited.

Disclaimer

Cisco Systems, Inc. assumes no responsibility for errors or
omissions that may appear in this guide. Cisco Systems, Inc.
reserves the right to change
this guide at any time without notice.
Printed in USA
EXPLORER
Digital Set-top
Model: 4240C and 4250C
5030 Sugarloaf Parkway;
Telephone 770-236-1077
Part Number 78-4015278-01 Rev C
20060628FDC
678.277.1120
www.cisco.com